Panasonic Electronic Board UB-T880W, UB-T880W Operating Instructions

Usage
21Operating Instructions
1
Volume Control
•The volume of the USB speaker on the elite Panaboard can be controlled using the Volume Dial, the 
volume of Windows, and the volume of the application being used. To adjust the volume, use the Volume 
Dial, or adjust the volume of the application.
Power Switch
•After turning the elite Panaboard off, wait more than 2 seconds before turning it back on.
Moving the elite Panaboard When Using the Stand (Sold Separately)
1.After confirming that the power is...

Usage
22 Operating Instructions
Installing the elite 
Panaboard software/book
You need to install the elite Panaboard software/book 
on the computer that will be used with the elite 
Panaboard.
To install the elite Panaboard software/book, follow the 
procedure below.
Notice
•Do not connect the USB cable until the 
installation is completed.
•Do not connect more than 1 elite Panaboard to 
the same computer. 
(Doing so can cause erroneous behavior on the 
computer.)
1.Turn on your computer and start the...

23
Operating Instructions
Usage
1
8.When the following screen is displayed, 
confirm that the USB cable is not connected to 
your computer or the elite Panaboard, and 
click [OK].
•If the USB cable is connected to the elite 
Panaboard, disconnect the cable, and click [OK].
•If .NET Framework 3.0 or later is not installed, an 
installation screen will be displayed. Follow the 
on-screen directions to install these components.
9.When the installation wizard is displayed, 
follow the on-screen instructions...

Usage
24 Operating Instructions
Setting the Projector
Set up your projector as instructed below.
About Positioning the Image
•
When you are projecting an image, make sure the 
image is inside the screen frame.
Project the Image as a Rectangle
•
Adjust the location of the projector to project at a 
right angle with the elite Panaboard.
•If the image is projected trapezoidally, the position 
may not be read correctly. Adjust the projector so 
that the projected image is a rectangle. Refer to your...

25
Operating Instructions
Usage
1
.
Setting Your System 
(Calibration)
About Calibration
Calibration refers to setting up the elite Panaboard and 
projector so that lines and comments drawn with your 
finger or the electronic pen are displayed in the correct 
position. Be sure to perform calibration before use.
After you have set up the elite Panaboard, project an 
image onto the screen board and use the elite 
Panaboard software installed on your computer to 
perform calibration.
After Calibration
Do...

Usage
26 Operating Instructions
4.Click [OK].
•If the elite Panaboard and projector are fixed so 
that they will not move (Wall mounted case), 
select the [Always use this calibration 
information.] check box, and click [OK] to skip 
calibration from the next time you start the elite 
Panaboard software.
•When calibration is finished, the   icon is 
displayed in the notification area. You can now 
use the elite Panaboard software.
•To display the Select Function Menu, click the 
Menu Start Tab (left...

27
Operating Instructions
Usage
1
Viewing the Help of the 
Software
Follow the procedure below to view the help of the 
software installed on your computer.
1.Turn on your computer and start Windows.
2.Open “Software Help” from the Start menu. 
([Start]  →   [All Programs] →    [Panasonic]  →   [elite 
Panaboard]  →   [Software Help])
•General help information of the installed software 
is displayed.
Note
•To access the help information of elite 
Panaboard software and Electronic Pen, 
click the   icon...

Appendix
28Operating Instructions
Appendix
Daily Care
When cleaning the elite Panaboard or inside the elite Panaboard, make sure to switch off the power and 
unplug the power cord from the AC outlet.
Cleaning the elite Panaboard
Gently wipe the elite Panaboard with a soft, moist 
cloth.
Notice
•The elite Panaboard is designed exclusively for 
projector images. 
To remove marks written with a whiteboard 
marker or stubborn stains, use whiteboard 
cleaner or neutral household detergent diluted 
with...

29
Operating Instructions
Appendix
1
Replacing the Penpoint of the 
Electronic Pen
As the penpoint of the electronic pen becomes worn, 
the penpoint will no longer slide easily across the 
surface. Continuing to use the electronic pen in this 
condition may make the screen dirty and cause 
malfunction. Replace the penpoint with a new one as 
soon as possible.
1.Remove the penpoint cover.
2.Remove the old penpoint and attach the new 
one.
3.Reattach the penpoint cover.
O
ld
 P
e
n p
o i
n
t
N ew
 P e
n p...

Appendix
30Operating Instructions
Troubleshooting
When experiencing problems, please refer to the table below for possible solutions. If the problem persists, 
contact your dealer.Symptom Possible cause and solution See page
The LEDs do not light 
when the power switch is 
turned on. Check that the power cord is properly plugged in.
→
If the problem persists, unplug the cord momentarily, wait about 
2 seconds, and plug it in again. —
Error LED (red) is 
blinking. Turn off the power, and turn it on.
→
If...