Panasonic Electronic Board UB-T780BP Operating Instructions

							•After calibration has completed, the  icon
is displayed in the notification area, and the
Desktop Drawing Tool is automatically
displayed.
[Desktop Drawing Tool]
• You will be able to use elite Panaboard
software.
Note
•The Desktop Drawing Tool shown above is
an example from version 3.1 of the elite
Panaboard software.
• For detailed information about using the
elite Panaboard software, refer to the
included electronic manual or the help
menu. For instructions on viewing the
electronic documentation "Operating
Instructions (For Software)", see "Viewing
the Electronic Documentation" (page 22).
Exiting the elite Panaboard software
Right-click on the 
 icon in the notification area, and
select [Exit] from the menu.
Uninstalling the elite
Panaboard software
If it is necessary to uninstall the elite Panaboard
software, follow the procedure below.
1. Turn on your computer and start Windows.
• Log into an account with Administrator
privileges.
2. Select [Add or Remove Programs] from the
Control Panel.
• In Windows 2000, select [Add/Remove
Programs], and in Windows Vista or
Windows 7, select [Uninstall a program].
3. Select Panasonic elite Panaboard, then remove
it.
4. Follow the on-screen instructions.
5. When uninstallation is complete, restart your
computer.Operating Instructions (For Basic Operations)21
1
Usage    
						

							Viewing the Electronic
Documentation
Follow the procedure below to view the electronic
documentation  "Operating Instructions (For Software) ".
1. Turn on your computer and start Windows.
2. Open "Operating Instructions (For Software)"
from the Start menu.
([Start]  ® [All Programs]  ® [Panasonic]  ® [elite
Panaboard]  ® [Operating Instructions for
Software])
• The electronic documentation will be displayed.
• For Windows 2000, [Programs] is displayed
instead of [All Programs].
Note
•To view the electronic documentation, you
must have Adobe ®
 Reader ®
 installed on
your computer. If your computer is
connected to the Internet, you can
download Adobe Reader from Adobe ’s web
site.
Download the Latest
Software
Follow the procedure below to download the latest
version of the software from the download web site.
1. Turn on your computer and start Windows.
2. On the Start menu, point to [All Programs]  ®
[Panasonic]  ® [elite Panaboard], and click
[Download the latest version].
22Operating Instructions (For Basic Operations)Usage 
						

							Daily CareWhen cleaning the elite Panaboard or inside the elite Panaboard, make sure to disconnect the USB cable.Cleaning the elite Panaboard
Gently wipe the elite Panaboard with a soft, moist cloth.
Notice•The elite Panaboard is designed exclusively for
projector images.
• For spots that are difficult to remove, use
commercially available white-board cleaner or
neutral household cleaner diluted with water.
• Do not use thinner, benzene, or abrasive
chemicals to clean.
(Doing so can result in discoloration.)
Replacing the Battery in the
Electronic Pen
When the charge in the battery in the electronic pen is
low, the message,  "The pen battery is low. Replace the
battery soon. " will be displayed on the computer screen.
Continued use of the electronic pen can lead to poor
performance. Replace the battery as soon as possible.
See "Inserting (Replacing) Batteries" (page 14) for
details on replacing the battery.
• Dispose of expired batteries quickly, by covering
the terminals in tape and following the disposal
regulations in your country/area.Operating Instructions (For Basic Operations)23
1
AppendixAppendix Após o uso as pilhas / baterias 
contidas neste produto poderão 
ser dispostas em lixo doméstico.
For Brazil Bij dit produkt zijn batterijen geleverd.
Wanneer deze leeg ziju, moet u ze niet
weggooien maar inleveren als KCA.
For Netherlands
Niet weggooien,
maar inleveren
als KCA.NLNL For Taiwan   
						

							Replacing the Penpoint of the
Electronic Pen
As the penpoint of the electronic pen becomes worn, a
hole will appear in the penpoint. Continuing to use the
electronic pen in this condition can cause damage to
the screen or unsatisfactory operation, so replace the
penpoint with a new one as soon as possible.24Operating Instructions (For Basic Operations)Appendix  
						

							TroubleshootingWhen experiencing problems, please refer to the table below for possible solutions. If the problem persists,
contact your dealer.SymptomPossible cause and solutionSee
pageThe LEDs do not light
when the USB cable is
connected to a computer.Check that the USB cable is properly connected.
→ If the problem persists, disconnect the USB cable from the
computer, and connect it again.
–Red LED is blinking.
Disconnect the USB cable from the computer, and connect it
again.
→ If the problem persists, contact your dealer.
–
The computer does not
recognize the elite
Panaboard.
• The elite Panaboard is not connected to the computer.
→ Ensure the elite Panaboard is properly connected to the
computer with a USB cable.
→ If the computer has two or more USB ports, use a different
USB port.
• The USB cable is connected to a USB hub.
→ Do not connect the elite Panaboard through a USB hub.
–
The connection between
the computer and the elite
Panaboard is
unexpectedly lost.
Check that the elite Panaboard is in an operable state, and that
the USB cable is properly connected.–
The electronic pen's
position is not correct.The projected image is misaligned.
→ Perform the calibration again.20
Drawn lines and
comments are not
completely displayed or
are displayed in the wrong
location.
The electronic pen loses
the functions.
• You are holding the electronic pen at an angle.
• You are operating the elite Panaboard in direct sunlight or
other strong lighting.
• Infrared controllers (e.g., a television remote control) are being
used and pointed towards the position sensor.
• There is a wall or ceiling close to the sides of the elite
Panaboard.
• There is an air-conditioner vent close to the elite Panaboard.
• A plasma or LCD television is being used near by the elite
Panaboard.
• Part of the position sensor is blocked.
• You are covering part of the electronic pen's sensor with your
hand.
• Several electronic pens are being used at the same time.
• The electronic pen is low on batteries.
→ Check that none of the above is causing the problem.
If misalignment is not caused by any of the above, perform the
calibration again.
–
Operating Instructions (For Basic Operations)25
1
Appendix 
						

							SymptomPossible cause and solutionSee
page
Extra lines are displayed
on the computer screen.
Apart from writing directly on the elite Panaboard with the
electronic pen, you pushed the penpoint with your finger while
holding it close to the elite Panaboard.
→ Avoid pushing the penpoint with your finger.
–
The message "The pen
battery is low. Replace the
battery soon."  is displayed
on the computer screen.
The electronic pen’s battery is weak.
→ Replace the electronic pen’s battery.14
23Marks written with a
white-board marker
cannot be erased.Because the elite Panaboard is designed exclusively for projector
images, you cannot erase the marks with a standard eraser.
→ Use commercially available white-board cleaner or neutral
household cleaner diluted with water.
23
26Operating Instructions (For Basic Operations)Appendix 
						

							SpecificationsModel NumberUB-T780BPGeneralPowerSupplied by the USB bus (AC power connection is not
required).Power Consumption5 V / 500 mA (USB BUS Power)External Dimensions: Height
´  Width  ´ Depth1,340 mm  ´ 1,752 mm  ´ 89 mm
(4 ft. 4  3
/4  in.  ´ 5 ft. 9 in.  ´ 3  1
/2  in.)Weight25 k g (55.11 lbs)Operating EnvironmentTemperature: 15 °C to 35 °C (59 °F to 95 °F)
Humidity: 30 % to 80 %Storage EnvironmentTemperature: -20 °C to 40 °C (-4 °F to 104 °F)
Humidity: 15 % to 80 %InterfaceUSB 2.0Input UnitScreen Board Size: Height  ´
Width1,175 mm  ´ 1,692 mm
(3 ft. 10  1
/4  in.  ´ 5 ft. 6  5
/8  in.)Interactive
FeaturesEffective Area:
Height  ´ Width1,165 mm  ´ 1,502 mm (3 ft. 9  7
/8  in.  ´ 4 ft. 11  1
/8  in.)
Project the image so that it is at least 5 mm ( 1
/4  in.) from
the screen frame. The electronic pen may not function
correctly within 50 mm (2 in.) of the position sensor in the
upper-left corner of the screen board.Electronic Pen PowerLR03 (AAA alkaline dry cell battery)  ´ 1Electronic Pen Battery Life30 hours (when used continuously at 25 °C [77 °F])
* When using Panasonic LR03 alkaline dry-cell batteries.Operating Instructions (For Basic Operations)27
1
AppendixProjectable Area 5 mm (
1/4 in.)
5 mm
(1/4 in.)
50 mm (2 in.)
5 mm (
1/4 in.)
77 in.  
						

							Supplies & AccessoriesOptional DeviceElectronic PenUE-608025StandKX-B061
•To purchase separately sold items, contact your dealer.
28Operating Instructions (For Basic Operations)Appendix 
						

							Installation Manual (for qualified service personnel)•Request assembly of the Electronic Board, stand and wall mounting from your dealer.
• Before constructing or installing the elite Panaboard, please read  "Installation Manual (for qualified service
personnel)" carefully.
Especially, please read "For Your Safety" carefully and install the elite Panaboard safely.
Panasonic System Networks Co., Ltd. cannot be held responsible for accidents or damage to property
resulting from incorrect installation.
• When installing the elite Panaboard on a wall or on the stand, perform installation with 2 people.For Your Safety
To prevent severe injury and loss of life, read this
section carefully before using the unit to ensure proper
and safe operation of your unit.
The following graphic symbols are used in this
Installation Manual.Denotes a potential
hazard that could
result in serious
injury or death.Denotes hazards
that could result in
minor injury or
damage to the unit.These symbols are used to alert
operators to a specific operating
procedure that must not be
performed.This symbol is used to alert operators
to a specific operating procedure that
must be emphasized in order to
operate the unit safely.NoticeSafety check must be done by qualified
service personnel after installing this
option.Be sure to disconnect the USB cable
while installing the unit. Otherwise, it may
cause electric shock or injury.Be sure to use the specified parts for the
installation. Otherwise, it may cause fire,
electric shock or injury.Notes in the operating instructions or
notes of labels on the cabinet, chassis or
parts should be observed.Do not alter the unit and install. Installing
an altered unit can cause fire, electric
shock or injury.Operating Instructions (For Basic Operations)29
1
Installation ManualInstallation ManualWARNING CAUTION   WARNING       
						

							Have the unit installed, removed and
disposed of only by qualified service
personnel.After installing or moving the electronic
board, lock the casters and set the
fall-prevention extension legs.If the unit is hung on a wall, confirm the
wall must be capable of supporting at
least the following weight.
1,324 N (135 k gf)Do not attach the electronic board to
mortared walls. Accidental electric
leakage from the wall mounting plate
bolts to metal laths or wire laths can
cause heat, smoke or a fire.Confirm the bolts of the unit are certainly
caught by the wall mounting plate by
pulling the unit after hanging the unit on
the wall mounting plate if the unit is
mounted on a wall.Be sure to put on a glove to avoid electric
shock or injury.30Operating Instructions (For Basic Operations)Installation Manual CAUTION  Locking the casters
(Push this side)
Push to lock