Panasonic Electronic Board UB-2815C, UB-2315C Operating Instructions

							41
Installation
Assembling the unit
■Accessories for assembling
The package includes the parts for setting up the unit shown below. Make sure that all of these parts are included 
in the package before proceeding.
No.Part NameIllustrationQ’tyRemarks
Power cord1
Connector cover1
Screw4
Washer4
Hexagonal wrench1
4
5 
						

							42
■Assembly
1First, lay the shipping box so that all joints are facing up.
Then, remove the joints and the shipping box.
•UB-2815C has twelve joints.
•UB-2315C has ten joints.
* This is a diagram of the UB-2815C.
UB-2315C is equipped with one board stopper and one board stopper lever.
•The shipping box, cushioning material, and other packing material will be necessary for repackaging this 
unit. Do not throw them away.
Shipping box
Sta nd
Cushions
Electronic board
Scanner
Shipping boxJoints Joints
Joints
•Markers (Black, Red, Blue)
 . . . . . . . . . . . . . . . . . . .1 each
•Eraser . . . . . . . . . . . . . .1
•Power cord . . . . . . . . . .1
•Software CD-ROM  . . . .1
•Operating Instructions. .1
•Warranty card*
1. . . . . . .1
•Connector cover . . . . . .1
•Screw  . . . . . . . . . . . . . .4
•Washer . . . . . . . . . . . . .4
•Hexagonal wrench  . . . .1
[Contents of Accessory box]
Whiteboard *
1 For U.S.A. models only.
Caution 
						

							43
Installation
2Remove the accessory box, two 
stands and four cushions (upper).
Note
•Be careful not to damage the whiteboard.
3Remove the two transportation 
plates.
Remove the two screws using the hexagonal 
wrench, and remove the transportation plate.
In the same way, remove the other side 
transportation plate.
Note
•Can not attach the stands without removing 
the transportation plates.
4Put the unit on the cushions 
(lower).
1) Lift the bottom (control box side) of the unit 
frame, and shift it 300 mm (1 3/16 ) to 
400 mm (1 9/16 ) and place it on the cushion 
(lower).
2) Remove the band holding the slider in.
Transportation plate
300 mm–400 mm
(1 3/16 –1 9/16 ) Band
Control box 
						

							44
5Attach the stands to the unit.
Each stand has four holes (A, B, C, D).
1) Attach the stand to the unit with the locking 
caster up.
2) When attaching the unit to the stand at normal 
height (1,858 mm [6 1 
5/32 ]), tighten the two 
screws with washers using the hexagonal 
wrench through holes A and C.
Note
•By tightening the two screws with washers 
through holes A and B, the unit will be 
positioned 100 mm (3 
15/16 ) higher than 
normal height (1,958 mm [6 5 5/32 ]).
6Stand the unit up and attach the 
whiteboard.
1) Stand the unit up.
2) Attach the whiteboard from behind by 
inserting the metal spindle of the whiteboard in 
the slot inside the frame of the unit.
A
B
C
D
A
B
C
Screw
Washer
Locking casters side
A
B
C
Back
Front 
						

							45
Installation
7Attach the scanner to the unit.
1) Take the scanner out.
2) Align the shaft of the scanner with the slot of 
the slider and push the shaft in the direction of 
the arrow 1 shown in the figure allowing the 
narrow part of the shaft to fit in the slot. Fit the 
shaft in the slot and return the shaft to the 
original position 2 until it is locked into place.
3) Connect both cables to the corresponding 
connectors. Secure both cables using the 
clamper.
4) Attach the connector cover with the black 
resin inside the cover.
8Connect the power cord.
Securely fit the supplied power cord in the AC 
inlet of the control box.
9Wipe the whiteboard surfaces.
Soak a soft cloth with water, wring well, and 
wipe the whiteboard surfaces.
10Remove the battery protection 
sheet.
11Check operations.
Refer to “Electronic Board Operations Check” 
on page 46.
1
12
2Shaft
Scanner
Slot Slider
Cables
Clamper Connectors
Connector Cover
Black Resin
AC inlet
Power cord 
						

							46
Electronic Board Operations Check
After assembling the unit, perform the procedures presented in the following table to make sure it functions properly.
StepPoints to Check
ConditionSolutions
1Turn the power switch on. Time set-up message is displayed 
after initial message is displayed.(Normal operation)
(If not) Check the power cord. (See 
step 8 on page 45.)
2Set the time.
(Refer to “Setting the current 
time” on page 20.)The time can be set. (Normal operation)
The time cannot be set. Contact the store or dealer from 
which the unit was purchased.
3Connect a USB flash memory 
device or SD memory card.
(Refer to “Scanning” on page 
14.)The USB flash memory device or 
SD memory card installed is 
recognized and is shown on the 
display.(Normal operation)
(If not) Contact the store or dealer from 
which the unit was purchased.
4Use the accessory marker to 
draw a large   across 
the entire scannable area of 
the whiteboard surface.
•For information on the 
scannable area, refer to 
“Whiteboard” on page 10.
Press the Start/Stop key.The scanner moves smoothly and 
the scanned image appears on the 
display.(Normal operation)
The scanner does not move 
smoothly.Check the connector.
(See step 7 on page 45.)
A strange noise is made. Check the scanner attachment.
(See step 7 on page 45.)
The scanned image is not 
displayed.Contact the store or dealer from 
which the unit was purchased.
The entire scannable area is not 
scanned.
5Zoom in on several areas of the 
scanned image.
(See page 15 or 16.)The image on the display matches 
the image on the whiteboard.(Normal operation)
A black or white horizontal line 
appears on the scanned image, or 
the image scanned is dark or 
blank.Check the white balance area, 
scanner lens and strong lighting.
(Refer to “Troubleshooting” on 
page 32.)
6Rotate the whiteboard.
(Refer to “Rotating the 
Whiteboard” on page 18.)The whiteboard can be rotated 
normally.(Normal operation)
The whiteboard cannot be rotated. Check the whiteboard 
attachment.
(See step 6 on page 44.)
7Turn off the power switch, then 
turn back on after 3 minutes.The standby message is displayed 
after the initial message is 
displayed.(Normal operation)
The time is not correct. Check the battery.
(See page 31.) 
						

							47
Installation
Repacking
Perform Assembly Steps 2 through 8 on pages 43 - 45 in reverse to repack the unit and accessories. Use the joints 
to fasten the shipping box.
* This is a diagram of the UB-2815C.
UB-2315C is equipped with one board stopper and one board stopper lever.
Shipping box
Stand
Cushions
Electronic board
Scanner
Shipping boxJoints Joints
Joints
•Markers (Black, Red, Blue)
 . . . . . . . . . . . . . . . . . . .1 each
•Eraser . . . . . . . . . . . . . .1
•Power cord . . . . . . . . . .1
•Software CD-ROM  . . . .1
•Operating Instructions. .1
•Warranty card*
1. . . . . . .1
•Connector cover . . . . . .1
•Screw  . . . . . . . . . . . . . .4
•Washer . . . . . . . . . . . . .4
•Hexagonal wrench  . . . .1
[Contents of Accessory box]
Whiteboard*
1 For U.S.A. models only. 
						

							© 2006 Panasonic Communications Co., Ltd. All Rights Reserved.
Printed in Japan
PJQXC0085ZA  F0706E0 Panasonic Digital Document Company,
Unit of Panasonic Corporation of North America
One Panasonic Way, Secaucus, New Jersey 07094
Panasonic Canada Inc.
5770 Ambler Drive, Mississauga, Ontario, L4W 2T3
Panasonic Business Systems U.K.
A Division of Panasonic U.K. Ltd.
Willoughby Road, Bracknell, Berkshire, RG12 8FP
Panasonic Marketing Europe GmbH
Hagenauer Strasse 43
65203 Wiesbaden, Germany
Matsushita Electric Industrial Co., Ltd.
http://panasonic.net
Information on Disposal for Users of Waste Electrical & Electronic Equipment (private households)
This symbol on the products and/or accompanying documents means that used electrical and electronic 
products should not be mixed with general household waste.
For proper treatment, recovery and recycling, please take these products to designated collection points, where 
they will be accepted on a free of charge basis. Alternatively, in some countries you may be able to return your 
products to your local retailer upon the purchase of an equivalent new product.
Disposing of this product correctly will help to save valuable resources and prevent any potential negative effects 
on human health and the environment which could otherwise arise from inappropriate waste handling. Please 
contact your local authority for further details of your nearest designated collection point.
Penalties may be applicable for incorrect disposal of this waste, in accordance with national legislation.
For business users in the European Union
If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further information.
Information on Disposal in other Countries outside the European Union
This symbol is only valid in the European Union.
If you wish to discard this product, please contact your local authorities or dealer and ask for the correct method of disposal.