Panasonic Electronic Board Ub 2815c Operating Instructions

41
Installation
Assembling the unit
■Accessories for assembling
The package includes the parts for setting up the unit shown below. Make sure that all of these parts are included 
in the package before proceeding.
No.Part NameIllustrationQ’tyRemarks
Power cord1
Connector cover1
Screw4
Washer4
Hexagonal wrench1
4
5 

42
■Assembly
1First, lay the shipping box so that all joints are facing up.
Then, remove the joints and the shipping box.
•UB-2815C has twelve joints.
•UB-2315C has ten joints.
* This is a diagram of the UB-2815C.
UB-2315C is equipped with one board stopper and one board stopper lever.
•The shipping box, cushioning material, and other packing material will be necessary for repackaging this 
unit. Do not throw them away.
Shipping box
Sta nd
Cushions
Electronic board
Scanner
Shipping boxJoints Joints...

43
Installation
2Remove the accessory box, two 
stands and four cushions (upper).
Note
•Be careful not to damage the whiteboard.
3Remove the two transportation 
plates.
Remove the two screws using the hexagonal 
wrench, and remove the transportation plate.
In the same way, remove the other side 
transportation plate.
Note
•Can not attach the stands without removing 
the transportation plates.
4Put the unit on the cushions 
(lower).
1) Lift the bottom (control box side) of the unit 
frame, and shift it...

44
5Attach the stands to the unit.
Each stand has four holes (A, B, C, D).
1) Attach the stand to the unit with the locking 
caster up.
2) When attaching the unit to the stand at normal 
height (1,858 mm [6 1 
5/32 ]), tighten the two 
screws with washers using the hexagonal 
wrench through holes A and C.
Note
•By tightening the two screws with washers 
through holes A and B, the unit will be 
positioned 100 mm (3 
15/16 ) higher than 
normal height (1,958 mm [6 5 5/32 ]).
6Stand the unit up and attach...

45
Installation
7Attach the scanner to the unit.
1) Take the scanner out.
2) Align the shaft of the scanner with the slot of 
the slider and push the shaft in the direction of 
the arrow 1 shown in the figure allowing the 
narrow part of the shaft to fit in the slot. Fit the 
shaft in the slot and return the shaft to the 
original position 2 until it is locked into place.
3) Connect both cables to the corresponding 
connectors. Secure both cables using the 
clamper.
4) Attach the connector cover with the...

46
Electronic Board Operations Check
After assembling the unit, perform the procedures presented in the following table to make sure it functions properly.
StepPoints to Check
ConditionSolutions
1Turn the power switch on. Time set-up message is displayed 
after initial message is displayed.(Normal operation)
(If not) Check the power cord. (See 
step 8 on page 45.)
2Set the time.
(Refer to “Setting the current 
time” on page 20.)The time can be set. (Normal operation)
The time cannot be set. Contact the...

47
Installation
Repacking
Perform Assembly Steps 2 through 8 on pages 43 - 45 in reverse to repack the unit and accessories. Use the joints 
to fasten the shipping box.
* This is a diagram of the UB-2815C.
UB-2315C is equipped with one board stopper and one board stopper lever.
Shipping box
Stand
Cushions
Electronic board
Scanner
Shipping boxJoints Joints
Joints
•Markers (Black, Red, Blue)
 . . . . . . . . . . . . . . . . . . .1 each
•Eraser . . . . . . . . . . . . . .1
•Power cord . . . . . . . . . .1...

© 2006 Panasonic Communications Co., Ltd. All Rights Reserved.
Printed in Japan
PJQXC0085ZA  F0706E0 Panasonic Digital Document Company,
Unit of Panasonic Corporation of North America
One Panasonic Way, Secaucus, New Jersey 07094
Panasonic Canada Inc.
5770 Ambler Drive, Mississauga, Ontario, L4W 2T3
Panasonic Business Systems U.K.
A Division of Panasonic U.K. Ltd.
Willoughby Road, Bracknell, Berkshire, RG12 8FP
Panasonic Marketing Europe GmbH
Hagenauer Strasse 43
65203 Wiesbaden, Germany
Matsushita...