Panasonic Dvd Vhs Home Theater Sound System Sc Ht830 Operating Instructions

							11
RQT7921
\
∫Batteries
Do not:
≥mix old and new batteries.
≥use different types at the same time.
≥heat or expose to flame.
≥take apart or short circuit.
≥attempt to recharge alkaline or manganese batteries.
≥use batteries if the covering has been peeled off.
Mishandling of batteries can cause electrolyte leakage which can 
damage items the fluid contacts and may cause a fire.
Remove if the remote control is not going to be used for a long period 
of time. Store in a cool, dark place.
∫Use
Aim at the sensor (l14), avoiding obstacles at a maximum range of 7 
m (23 feet) directly in front of the unit.After plugging the unit into your household AC outlet and pressing [Í] 
to turn the unit on for the first time, the unit automatically tunes in all 
the channels it can receive and sets the clock.
The unit determines the type of transmission, TV or CATV, as follows:
TV: when there are less than 5 CATV channels.
CATV: when there are 5 or more CATV channels.
Preparation
≥Confirm that the antenna is connected correctly.
≥Turn on the television and select the video input for the VHS.
≥Press [VHS] to put the remote control in VHS mode.
Press [Í] to turn on the unit.
Plug-in Auto Tuning starts and the unit puts the stations it can receive 
into channels (l37, Channel range).
The unit starts auto clock setting when finished, then displays the time.
[Note]
If auto tuning stops partway (by changing the source, turning the unit 
off, or due to a power failure).
1 Disconnect the AC power supply cord on the main unit and then 
reconnect it.
2 Turn on the main unit.
To cancel partway
Press [MENU].
∫To start Plug-in Auto Tuning again (after relocation, for 
example)
Preparation
≥Press [Í] to turn on the unit.
≥Make sure there is no video cassette tape loaded in the unit.
≥Press [DVD/VHS] to select “VHS” as the source.
1 Press and hold [WCH] and [XCH] on the main unit simultaneously 
for 3 seconds until the channel changes to “2”.
2 Disconnect the AC power supply cord on the main unit and then 
reconnect it.
3 Turn on the main unit. Plug-in Auto Tuning restarts.
∫To set the channels manually (l37).
∫If the unit couldn’t set the clock automatically
The MANUAL CLOCK SET screen appears. Set the time manually 
(l36).
VOLUME
123
4
56
78
0
DISC
9
CH
NAVI
SKIPSLOW/SEARCH
MENU
ENTER
DIRECT 
NAVIGATOR
TOP MENU
RETURN
STATUS/
FUNCTIONS
TVFM/AM DVD/VHS
DV D T V
VHSTUNER
PICTURE MODE
SETUP
OPEN/CLOSE/EJECTJET REW
ENTER
PLAY 
LIST
INPUT SELECTOR
DVD/VHS
VHS
MENU
S10
CHPOWER    /I 
OPEN/CLOSEEJECTDISC CHECK/REW FF/STOP PLAYDOWN UPPHONES
VOLUMESTOP-DEMOPLAYH.BASSRECCH
STEP6The remote control
Remote controlBatteries
1
2
3
R6/LR6, AA, UM-3
≥Insert so the poles (i and 
j) match those in the 
remote control.
≥Do not use rechargeable 
type batteries.
Antenna system and channel captions all revert to the default 
values when you perform the procedure above. Reset the timer 
recording settings. (If necessary reset the clock first. l36, 
CLOCK SET)
STEP7Plug-in Auto Tuning
AUTO CHANNEL SET
PROCEEDING
END :MENU2
Disappears     2
RQT7921-P_ENG.book  11 ページ  ２００５年５月２５日　水曜日　午後３時２４分 
						

							12
RQT7921
You can control the television by entering the remote control code.
1Refer the following chart for the code 
for your television.
2Aiming the remote control at the television
While pressing and holding [TV], press 
the numbered buttons to enter the code 
number.
≥Example: To select 01, press [0] l [1].
≥The remote control outputs the on/off signal. If the code is 
correct, the equipment turns on or off. If it doesn’t, try entering 
another code.
[Note]
≥If your television brand is not listed or if the code listed for your 
television does not allow control of your television, this remote 
control is not compatible with your television.
≥Re-enter the codes after you change the batteries.
∫TV operation
Switch the remote control mode to TV. Press [TV] before doing TV 
operations. When in TV mode, the [TV] button lights each time you 
press an operation button.
Turn on the television and select the video input for the DVD.
The QUICK SETUP screen assists you to make necessary 
settings such as:
≥Menu Language (l27)
≥TV Type (l26)
≥TV Aspect (l26)
1Press [DVD] to put the remote control 
in DVD mode.
2Press [Í] to turn on the unit.
3Press [DVD/VHS] to select “DVD/CD” as 
the source.
4Press [SHIFT]i[SETUP] to show 
QUICK SETUP screen.
5Follow the messages and make the 
settings using [3421] and 
[ENTER].
6Press [ENTER] to finish QUICK SETUP.
7Press [SHIFT]i[SETUP] to exit.
To change these settings later
Select “ QUICK SETUP” in “Others” tab (l27).
To return to the previous screen
Press [RETURN].
ManufacturerCode No.ManufacturerCode No.
Panasonic 01, 02 PHILIPS 06
FISHER14PIONEER02, 10, 19
G.E. 02, 03, 07, 09 QUASAR 02
GOLD STAR07, 15RCA03, 07, 09, 13, 
23, 24, 25
HITACHI 05, 07 SANYO 14
JVC12SHARP08, 21
LXI 03, 06, 07, 10, 
14, 15SONY 04
MAGNAVOX06, 07, 11, 15, 
22SYLVANIA06, 07, 15
MITSUBISHI 07, 15, 16, 21 SYMPHONIC 17
NEC07, 15TOSHIBA10, 21
PHILCO 06, 07 ZENITH 18, 20
VOLUME
123
4
56
78
0
DISC
9
CH
NAVI
CANCEL SPEED PROG
SKIPSLOW/SEARCH
MENU
ENTER
DIRECT 
NAVIGATOR
TOP MENU
RETURN
STATUS/
FUNCTIONS
TVFM/AM DVD/VHS
DV D T V
VHSTUNER
PICTURE MODE
SETUP
OPEN/CLOSE/EJECTJET REW
ENTER
PLAY 
LIST
TV VOL
TV VOLMULTI RE-MASTER QUICK OSDMIX 2CH 
ZOOMPROGRESSIVE 
CD MODEREPEAT
PLAY MODE
H.BASSSUBWOOFER LEVELC.FOCUS 
SFCTESTSUPER SRNDCH SELECTMUTING
CM SKIPADVANCE
DISC REVIEW
QUICK 
REPLAYREC
SLEEP
   PLAUDIORESET
TV/VIDEOSHIFT SHIFT
INPUT SELECTOR
CH       CH
TV
TV VOL
STEP8, 2
TV VOL
TV/VIDEOSHIFT
RETURN
ENTER
SETUPTV
Numbered
buttons
DVD
DVD/VHS
S10
STEP8, 2
STEP8TV manufacturer setting
Operation Buttons
Remote control 
TV mode[TV]
Power on/
standby[ÍTV]
TV/Video switch [TV/VIDEO]
Selecting 
channels[WCH], [XCH] or numbered buttons 
[1–9, 0,S10/ENTER].
≥[S10/ENTER] is used to confirm channel 
selection on some televisions manufactured by 
other companies.
Adjusting 
volume[TV VOLj] [TV VOLi]
STEP9DVD QUICK SETUP
Setup
English
EspañolFrançais
ENTERRETURNto  select and pressto  return
Select the menu language.
QUICK SETUP
RQT7921-P_ENG.book  12 ページ  ２００５年５月２５日　水曜日　午後３時２４分 
						

							13
RQT7921
Control reference guide
≥See reference pages in brackets.
Remote control
VOLUME
123
4
56
78
0
DISC
9
CH
NAVI
CANCEL SPEED PROG
SKIPSLOW/SEARCH
MENU
ENTER
DIRECT 
NAVIGATOR
TOP MENU
RETURN
STATUS/
FUNCTIONS
TVFM/AM DVD/VHS
DV D T V
VHSTUNER
PICTURE MODE
SETUP
OPEN/CLOSE/EJECTJET REW
ENTER
PLAY 
LIST
TV VOL
TV VOLMULTI RE-MASTER QUICK OSDMIX 2CH 
ZOOMPROGRESSIVE 
CD MODEREPEAT
PLAY MODE
H.BASSSUBWOOFER LEVELC.FOCUS 
SFCTESTSUPER SRNDCH SELECTMUTING
CM SKIPADVANCE
DISC REVIEW
QUICK 
REPLAYREC
SLEEP
   PLAUD IORESET
TV/VIDEOSHIFT
INPUT SELECTOR
S10
TV Power button (12)
Top menu button (22)
Direct navigator button (23)
Jet navigator button (34)
Status button (35)
Function button (24)
TV volume down button (12)
To use functions labelled in orange
While pressing [SHIFT], press the
corresponding button
MULTI RE-MASTER.... (21)QUICK OSD......... (18)MIX 2CH........... (42)ZOOM............. (19)
Basic operations for play
Play button (16, 28), Stop button (17, 28)
Open/close button (17), Tape eject button (28)
Pause button (17, 28), Press and hold for slow (28)
Select television channels and title number etc.Enter numbers (17)
Picture mode button (29)
Menu button (22, 36), Play list button (23)
Return button (17), TV volume up button (12) Selection/Enter on the television’s screen Switch the source on the main unit between DVD 
and VHS.
DVD/VHS source button (12)
Switch the source on the main unit to tuner and 
change the band.
Tuner/band button (40)
Basic operations for play
Skip buttons (17), Index search button (35)
Slow/search buttons (17), Jet rewind button (28)
Fast-forward/rewind button (28), Tuning buttons (40)
Volume buttons (16) Channel select (12, 30, 40)
Tracking, and vertical hold buttons (29)
Remote control mode selector button
[DVD] (12), [VHS] (28), [TV] (12), [TUNER] (40)
Changes the remote control mode. The button lights 
once pressed. The selected mode is held in memory 
until you press another mode selector button. The mode 
selector button lights each time you press an operational 
control button showing which mode is in use.
Turn the unit on (11, 12)
DVD SETUP menu button (12, 26)
Disc buttons (17)
PROGRESSIVE......(17)CD MODE..........(18)REPEAT.......... (19)PLAY MODE.. (20, 40)
H.BASS............ (42)
SUBWOOFER LEVEL.... (42)
C.FOCUS........... (41)
SFC.............. (41)
TEST .............(41)
SUPER SRND........(41)
CH SELECT....... (41)
MUTING.......... (42)
CM SKIP............ (18)
PROG............. (32)
ADVANCE
DISC REVIEW
....... (18)
SPEED............ (32)
QUICK
REPLAY
..........(18)
...............(32)REC............ (30)
SLEEP............. (42)
PL Ⅱ.......... (41)AUDIO......(19, 39)
CANCEL............(17)
RESET.......... (35)
TV/VIDEO........ (12)
≥Intervals between buttons are changed.
RQT7921-P_ENG.book  13 ページ  ２００５年５月２５日　水曜日　午後３時２４分 
						

							14
RQT7921
∫Common display
[1]Program indicator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20, 40
[2]H. Bass indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
[3]Wireless Theater indicator. . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
≥Indicates when you use the Digital Transmitter and Receiver.
[4]Center Focus indicator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
[5]Sound Field Control indicator. . . . . . . . . . . . . . . . . . . . . . . . 41
[6]Dolby Pro Logic II indicator . . . . . . . . . . . . . . . . . . . . . . . . . 41
[7]Super Surround indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
[8]SLEEP timer indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
[9]Main display (Orange)
Disc play elapsed time, program recording start time, volume, 
TUNER frequency/channel display, various messages, etc.
[10]Main display (White)
Time display, video play/record elapsed time, program recording 
end time, various messages, etc.
∫DVD operation
1CD mode indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Lights when CD mode is on.
2DVD selector indicator
Lights when DVD is selected.
3Operation status of DVD section
≥Displays play status graphically.
Rotating: playing
Stopped: paused
Blinking: Standby to resume play (l17, Stop)
≥Numeric indicator lights corresponding to disc tray number.
4DTS indicator
5Progressive video indicator. . . . . . . . . . . . . . . . . . . . . . . . . . 17
6Dolby Digital indicator7Down mix indicator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
8HDCD indicator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
9Play sequence indicator
CD mode indicator + RND: During all disc random play. . . . . 21
RND: During random play. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
: During repeat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
AB: During A-B repeat . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
:Title/Group/Playlist/Chapter/Track/Program display
∫VHS operation
1VHS selector indicator
Lights when the selector is in VHS mode.
2Operation status of VHS section
≥Lights when a video cassette is inserted.
≥Blinks when recording or timer recording is attempted with no 
video cassette inserted.
≥Displays play status graphically.
Rotating: playing
Stopped: paused
3Recording indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
4Repeat playback indicator. . . . . . . . . . . . . . . . . . . . . . . . . . . 29
5Tape speed indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
6Timer program recording indicator. . . . . . . . . . . . . . . . . . . . 32
7Channel display
∫Tuner operation
[1]Radio broadcast display . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
MONO: Forced monaural
ST: Stereo
TUNED: Receiving radio signal
[2]Band display
Main unit and subwoofer
OPEN/CLOSEEJECTDISC CHECK
/REW FF/STOP PLAY
DOWN UPPHONES
VOLUMESTOP-DEMOPLAYH.BASSRECCH
Drawer l16
Disc buttons 
[DISC1–5] l16
Disc change button l16
Drawer open/close button l16
Disc check button l16
Ta p e  s l o t  l28Fast-forward and 
rewind buttons l28
Tape eject button l28
Channel buttons l11
Input selector button 
VHS>DVD/CD>FM>AM
^"""""""""""""n
DVD stop button l16
DVD play button l16
Demo button l9
DisplayVHS stop button l28
VHS play button l28
Headphone terminal l42
Volume dial l16
Recording button l30
AC supply indicator [AC IN]
≥This indicator lights when the subwoofer is connected to the 
household AC outlet and through the system cable to the main unit.
≥When main unit is turned on, this indicator will light on or vice versa.
≥The indicator light turns off in approximately 10 seconds after the 
unit is disconnected from the AC outlet.
H. Bass 
button l 42
Power button [Í/I POWER] l11; Press to switch the unit from on to standby mode or vice versa.
In standby mode, the unit is still consuming a small amount of power.
Remote control 
signal sensor
[Note]
≥“BYE” is displayed when the unit turns off.
Remove the power plug after this display 
disappears.
Main unit display
REC
SP
LPEPD.MIXRNDDTS
PGM
S.SRND SLEEPALL ALLPROG.DIGITALHDCDST MONO
dB
C.F
CH
VPSFCABCDPL II
PLCT PGTG
H.BASS
TUNEDw
21[1]
6 [9][8] 457[5][3]
:[6]4[2][4] 3 2 8 95 3 [1] 6 1
[2]7[7]
[10]
RQT7921-P_ENG.book  14 ページ  ２００５年５月２５日　水曜日　午後３時２４分 
						

							15
RQT7921
Discs that can be played
§A process that allows play on compatible equipment.
≥It may not be possible to play the above discs in all cases due to the type of disc or condition of the recording.
Note about using a DualDisc
The digital audio content side of a DualDisc does not meet the technical specifications of the Compact Disc Digital Audio (CD-DA) format so play 
may not be possible.
∫Discs that cannot be played
PAL discs (except DVD-Audio), DVD-ROM, CD-ROM, CDV, CD-G, 
SACD, Divx Video Discs and Photo CD, DVD-RAM that cannot be 
removed from their cartridge, 2.6-GB and 5.2-GB DVD-RAM, and 
“Chaoji VCD” available on the market including CVD, DVCD and 
SVCD that do not conform to IEC62107.
∫To prevent damage
Do not;
≥load more than one disc per tray.
≥close the drawer by hand.
∫To clean discs
Wipe with a damp cloth and 
then wipe dry.
∫Handling precautions
≥Do not attach labels or stickers to discs (This may cause disc 
warping, rendering it unusable).
≥Do not write on the label side with a ball-point pen or other writing 
instrument.
≥Do not use record cleaning sprays, benzine, thinner, static electricity 
prevention liquids or any other solvent.
≥Do not use scratch-proof protectors or covers.
≥Do not use the following discs:
– Discs with exposed adhesive from removed stickers or labels 
(rented discs etc).
– Discs that are badly warped or cracked.
– Irregularly shaped discs, such as heart shapes. Logo DiscIndication in 
operating 
instructionsRemarks
DVD-RAM[RAM]Recorded using Version 1.1 of the 
Video Recording Format (a unified 
video recording standard).≥Recorded with DVD video recorders, DVD 
video cameras, personal computers, etc.
≥Remove discs from their cartridges before use.
[JPEG]Recorded using the DCF (Design 
rule for Camera File system) 
standard Ver 1.0.
≥Recorded with Panasonic DVD-Video recorders.
≥To play JPEG files, select “Play as Data 
Disc” in Other Menu (l25).
DVD-Audio[DVD-A]—
[DVD-V]Some DVD-Audio discs contain DVD-Video content.
To play DVD-Video content, select “Play as DVD-Video” in Other Menu (l25).
DVD-Video
[DVD-V]—
DVD-R 
(DVD-Video)/
DVD-RW 
(DVD-Video)Discs recorded and finalized
§ on DVD video recorders or DVD video cameras.
—iR (Video)/
iRW (Video)
Video CD
[VCD]—
SVCDConforming to IEC62107
CD[CD]This unit is compatible with HDCD, but does not support the Peak Extend function.
(A function which expands the dynamic range of high level signals)
HDCD-encoded CDs sound better because they are encoded with 20 bits, as 
compared with 16 bits for all other CDs.
≥During HDCD play, “HDCD” lights on the unit’s display.
—CD-R
CD-RW[WMA]
[MP3]
[JPEG]
[CD]
[VCD]≥This unit can play CD-R/RW (audio recording disc) recorded with the formats on the 
left. Close the sessions or finalize
§ the disc after recording.
≥HighMATTM discs
WMA, MP3 or JPEG files only.
To play without using the HighMAT
TM function, select “Play as Data Disc” in Other 
Menu (l25).
≥[WMA] This unit is not compatible with Multiple Bit Rate (MBR: a file that contains the 
same content encoded at several different bit rates).
HighMAT and the HighMAT logo are either 
trademarks or registered trademarks of 
Microsoft Corporation in the United States 
and/or other countries.
, HDCD
®, High Definition Compatible Digital® and 
Pacific Microsonics™ are either registered trademarks or 
trademarks of Pacific Microsonics, Inc. in the United States and/or 
other countries.
HDCD system manufactured under license from Pacific 
Microsonics, Inc. This product is covered by one or more of the 
following: In the USA : 5,479,168, 5,638,074, 5,640,161, 
5,808,574, 5,838,274, 5,854,600, 5,864,311, 5,872,531, and in 
Australia: 669114, with other patents pending.
Disc handling
RQT7921-P_ENG.book  15 ページ  ２００５年５月２５日　水曜日　午後３時２４分 
						

							16
RQT7921
Basic play
Turn on the television and select the appropriate video input for the DVD.
[Note]
≥When “Press PLAY to resume play” is displayed, this position is 
memorized even after turning off the unit, changing the source. 
(Power off resume)
≥Total title number may not be displayed properly on iR/iRW.
VOLUME
123
4
56
78
0
DISC
9
CH
NAVI
CANCEL SPEED PROG
SKIPSLOW/SEARCH
MENU
ENTERDIRECT 
NAVIGATOR
TOP MENU
RETURN
STATUS/
FUNCTIONS
TVFM/AM DVD/VHS
DV DTV VHS
TUNER
PICTURE MODE
SETUP
OPEN/CLOSE/EJECTJET REW
ENTER
PLAY 
LIST
TV VOL
TV VOLMULTI RE-MASTER QUICK OSDMIX 2CH 
ZOOMPROGRESSIVE 
CD MODEREPEAT
PLAY MODE
H.BASSSUBWOOFER LEVELC.FOCUS 
SFCTESTSUPER SRNDCH SELECTMUTING
CM SKIPADVANCE
DISC REVIEWQUICK 
REPLAYRECSLEEP
   PLAUDIORESET
TV/VIDEOSHIFT
INPUT SELECTOR
123
4
5,6
7
8 3S10OPEN/CLOSEEJECTDISC CHECK
/REW FF/STOP PLAY
DOWN UPPHONES
VOLUMESTOP
-DEMO
PLAYH.BASSRECCH
VOLUME
DOWN UP
DISC CHECKDISC CHANGE
STOP
2Turn on the unit.
 POWERÍ   I
5Open the disc tray 
and load the disc.
≥Load double-sided discs so the label for the 
side you want to play is facing up.
6Close the disc tray.
≥To load discs on the other trays, 
repeat steps 4–6.
OPEN/CLOSE
OPEN/CLOSE
7Start play.
≥Press [∫] to stop play.
PLAY
1Put the remote 
control in DVD 
mode.
DV D
4Select the disc tray.
12345 DISC
8Adjust the volume.
––dB N 0dB
(Minimum)
 (Maximum)
Volume may be lower when playing 
DVD-Video than when playing other discs or during 
television broadcasts. Reduce the volume before playing 
other sources or returning to the television so volume 
doesn’t increase suddenly.
3Select “DVD/CD”.
INPUT SELECTOR
Using main unit
Checking 
the disc 
trays
All trays except the tray in 
play open without interrupting 
play. While stopped, all trays 
will open.
≥Press [DISC CHECK] again 
to close the trays.
≥Do not pull out the trays, 
remove or insert discs 
during the disc check.
Changing 
the discs 
during play
You can change the other 
discs without interrupting 
play.
≥After selecting the disc tray, 
press [< DISC CHANGE] to 
close the tray.
DISC CHECK
DISC CHANGE
If you are experiencing problems, refer to troubleshooting (l45–
47).
12345 DISC
RQT7921-P_ENG.book  16 ページ  ２００５年５月２５日　水曜日　午後３時２４分 
						

							17
RQT7921
[Note]
≥Discs continue to rotate while menus are displayed. Press [∫] when 
you finish to preserve the unit’s motor and your television screen.
Using remote control
Progressive 
video
St o p
The position is memorized while 
“Press PLAY to resume play” is 
on the screen.
≥Press [1] (play) to resume.
≥Press [∫] to clear the position.
≥
This may not work while playing 
some parts of a disc or at all 
with some discs (only when the 
elapsed play time can be 
displayed).
≥Power off resume (l16)
Open/Close
≥You can open a disc tray even 
when the unit is in standby 
mode.
Pause≥Press [1] (play) to restart play.
Search
(during play)≥Up to 5 steps
≥Press [1] (play) to start play.
Slow-motion
(during pause)[RAM]
 [DVD-V] [VCD]
≥[VCD] Slow motion, forward 
direction only
Frame-by-
frame
(during pause)[DVD-A]
 (Motion picture part)
[RAM] [DVD-V] [VCD]
≥[VCD] forward direction only
VOLUME
123
4
56
78
0
DISC
9
CH
NAVI
CANCEL SPEED PROG
SKIPSLOW/SEARCH
MENU
ENTER
DIRECT 
NAVIGATOR
TOP MENU
RETURN
STATUS/
FUNCTIONS
TVFM/AM DVD/VHS
DV DTV
VHSTUNER
PICTURE MODE
SETUP
OPEN/CLOSE/EJECTJET REW
ENTER
PLAY 
LIST
TV VOL
TV VOLMULTI RE-MASTER QUICK OSDMIX 2CH 
ZOOMPROGRESSIVE 
CD MODEREPEAT
PLAY MODE
H.BASSSUBWOOFER LEVELC.FOCUS 
SFCTESTSUPER SRNDCH SELECTMUTING
CM SKIPADVANCE
DISC REVIEW
QUICK 
REPLAYRECSLEEP
   PLAUDIORESET
TV/VIDEOSHIFT SHIFT
INPUT SELECTOR
SHIFT
RETURNMENU TOP MENU 
DIRECT NAVIGATOR
DVD
ENTER
PROGRESSIVE
DISC
CANCEL
Numbered
buttons
S10
OPEN/CLOSE,
SHIFT
PROGRESSIVECD MODE
i
PROG.
OPEN/CLOSE/EJECT
OPEN/CLOSE/EJECT
SHIFT
i
SLOW/SEARCH
ENTER
Skip≥[WMA] [MP3] [JPEG]
[3, 4]:  Group skip during 
play
[2, 1]:  Content skip during 
play
On-screen 
item select
Enter number
[RAM] [DVD-A] 
[DVD-V] [VCD] [CD]
e.g. To select 12:
[S10] l [1] l [2]
[VCD] 
with playback control (PBC) 
To cancel the playback control, 
press [∫] and then press the 
numbered buttons.
[WMA] [MP3] [JPEG]
e.g. To select 123:
[1] l [2] l [3] l [ENTER]
≥Press [CANCEL] to cancel the 
number(s).
[DVD-A] [DVD-V]
Shows a disc top menu
[RAM]
 
Plays the programs (l23)
Disc menu
[DVD-V]
Shows a disc menu
[RAM]
 
Shows the play list (l23)
[VCD]
Shows a disc menu
Return to 
previous 
screen
Selecting the 
disc directly
≥Disc information (l18)
≥You can select the disc with 
[DISC1–5] on the main unit. 
SKIP
ENTER
ENTER
Select
Register
123
4
56
78
09
ENTERS10
OPEN/CLOSE/EJECT
CANCEL
ENTER
NAVI
TOP MENU
DIRECT 
NAVIGATOR
MENU
RETURN
RETURN
DISC
123
4
5
i[Remember]
 Press [DVD] first.
RQT7921-P_ENG.book  17 ページ  ２００５年５月２５日　水曜日　午後３時２４分 
						

							18
RQT7921
Convenient functions
You can select the disc after checking the discs loaded with the Disc 
information screen.
≥You can also select the disc directly with 5 DISC SELECTOR 
buttons on the main unit.
1Press [DISC] to show the Disc 
information screen.
2Press the numbered buttons ([1] – [5]).
To clear the screen
Press [DISC].
≥You can not select a tray with no disc.
Press [QUICK OSD].
The current playback condition screen is displayed.
≥To exit the screen
Press [QUICK OSD].
≥[CD] [MP3] [WMA] Quick OSD screen will appear automatically. 
≥If there is a JPEG data in the disc, Quick OSD screen will not appear 
automatically. [VCD]
 [CD] [WMA] [MP3]
This feature is very convenient if you want to play several music CDs 
sequentially. Make sure that applicable discs are on the tray before 
playing. (l Disc information, left)
DVD and JPEG files are skipped without being played.
1While stopped
Press [CD MODE].
2Press [1] (play).
≥If all loaded discs are DVD, JPEG, or unchecked, CD Mode does not 
work.
≥HighMAT
TM menus and Video CD playback control are disabled.
≥You cannot change the mode during program play, random play or 
CD mode play. (l20)
≥If you want to play a DVD, press [CD MODE] again to cancel CD 
Mode. (CD Mode is also canceled when you switch the unit to 
standby.)
≥If no disc is loaded in the player, CD Mode will not function.
(Only when the elapsed play time can be displayed)
(Except iR/iRW)
Press [QUICK REPLAY] to skip back a few 
seconds.
[RAM] [DVD-V] (Except iR/iRW)
Allows you to browse the disc contents and start playing from the 
selected position. You can select either “Intro Mode” or “Interval Mode” 
in “Advanced Disc Review” in the “Disc” tab (l26).
1Press [ADVANCE DISC REVIEW].
≥Quick OSD screen is displayed
2Press [1] (play) when you find a title/
program to play.
≥This may not work depending on the disc and the play condition.
[RAM] [DVD-V]
 (Except iR/iRW)
Play restarts from approximately a minute later. Convenient when you 
want to skip commercials etc.
During play
Press [CM SKIP].
[RAM] 
≥It is not possible to skip the program if the start of the next program is 
within about one minute of the point you skipped from.
Disc information
Displaying current playback 
condition (QUICK OSD)
VOLUME
123
4
56
78
0
DISC
9
CH
NAVI
CANCEL SPEED PROG
SKIPSLOW/SEARCH
MENU
ENTER
DIRECT 
NAVIGATOR
TOP MENU
RETURN
STATUS/
FUNCTIONS
TVFM/AM DVD/VHS
DV DTV
VHSTUNER
PICTURE MODE
SETUP
OPEN/CLOSE/EJECTJET REW
ENTER
PLAY 
LIST
TV VOL
TV VOLMULTI RE-MASTER QUICK OSDMIX 2CH 
ZOOMPROGRESSIVE 
CD MODEREPEAT
PLAY MODE
H.BASSSUBWOOFER LEVELC.FOCUS 
SFCTESTSUPER SRNDCH SELECTMUTING
CM SKIPADVANCE
DISC REVIEW
QUICK 
REPLAYREC
SLEEP
   PLAUDIORESET
TV/VIDEOSHIFT SHIFT
INPUT SELECTOR
DVD
SHIFT ZOOMAUDIO
QUICK  
REPLAY
CD MODE
REPEAT
ADVANCE 
DISC REVIEW
QUICK OSD
CM SKIP
DISCS10
Numbered
buttons [1]   [5]
DISC
SETUP
Disc Information
CD
DVD-Audio
Unchecked
No Disc
DVD-VideoTrack 10 Time 60:15
Not yet read Empty
MULTI RE-MASTER QUICK OSD
ChapterTime4Title1 0:41:23
Program Playback
e.g. [DVD-V]Current playback number Elapsed play time
Playback
condition
Current position Play mode
CD Mode 
(CD sequential play)
Quick replay
Reviewing title to play 
(Advanced Disc Review)
Skipping one minute forward 
(CM skip)
PROGRESSIVE
CD MODE
CD
QUICK REPLAY
SPEED ADVANCE
DISC REVIEW
ProgramTime4 0:01:06
04
e.g. [RAM]
PROGCM SKIP
RQT7921-P_ENG.book  18 ページ  ２００５年５月２５日　水曜日　午後３時２４分 
						

							19
RQT7921
[DVD-A] (Motion picture part) [RAM] [DVD-V] [VCD]
Expands the letterbox picture to fit the screen.
Press [ZOOM] several times to select the 
preset aspect ratio (Just Fit Zoom) or 
“Auto”. 
Fine adjustments (Manual Zoom)
After selecting the preset aspect ratio or “Auto”, press [21].
–from k1.00 to k1.60 (in 0.01 units)
–from k1.60 to k2.00 (in 0.02 units)
≥Press and hold [21] to alter faster.
[DVD-A]
 [DVD-V] (with multiple soundtracks) [RAM] [VCD]
Changes the soundtrack.
Press [SHIFT]i[AUDIO] several times to 
select the soundtrack.
[RAM] [VCD]
You can use this button to select “L”, “R” or “LR”.
[DVD-V] (Karaoke discs)
Press [21] to select “On” or “Off” of vocals.
Read the discs instructions for details.
Signal type/data
LPCM/PPCM/ÎDigital/DTS/MPEG: Signal type
kHz (Sampling frequency)/bit/ch (Number of channels)
Example:
3
/2 .1ch(Only when the elapsed play time can be displayed
[JPEG]: Works with all JPEG content.)
During play
Press [SHIFT]i[REPEAT] several times to 
select an item to be repeated.
[RAM] PG (Program)>Disc>Off
≥During play list play: Scene>PL (Playlist)>Off
[DVD-A]
 Tr a c k>Group§>Off
[DVD-V] Chapter>Title
§>Off
[VCD]
 [CD] Tr a c k>Disc>Off
≥When CD Mode is on: Track>Disc>All CD’s>Off
≥When CD Mode is on, during program and random play: 
Track>All CD’s>Off
[WMA] [MP3] 
Content>Group§>Off
≥When CD Mode is on: Content>Group>All CD’s>Off
≥When CD Mode is on, during program and random play: 
Content>All CD’s>Off
[JPEG] 
Group§>Off§“All” is displayed, program and random play.
Changing the zoom ratio 
(Zoom)
Changing soundtracks 
(Audio)
.1: Low frequency effect
.1:(not displayed if there is no signal)
.0: No surround
.1: Mono surround
.2: Stereo surround (left/right)
.1: Center
.2: Front leftiFront right
.3: Front leftiFront rightiCenter
MIX 2CH
ZOOM
Functions
Just Fit Zoom1.00
4:3 Standard
European Vista
16:9 Standard
American Vista
Cinemascope1
Cinemascope2 Auto
16:9 Standard (16:9)
4:3 Standard (4:3)
European Vista  (1.66:1)
American Vista (1.85:1)
Cinemascope1 (2.35:1)
Cinemascope2 (2.55:1)
SHIFTCANCELAUDIOr
Functions
Audio 1
Repeat playSHIFTREPEAT
PLAY MODEr
Functions
Repeat Off
Chapter
Title Off
e.g. [DVD-V]
[Remember] Press [DVD] first.
RQT7921-P_ENG.book  19 ページ  ２００５年５月２５日　水曜日　午後３時２４分 
						

							20
RQT7921
Convenient functions
1While stopped, press [PLAY MODE].
[Note]
≥The program is cleared when you switch the unit to standby, select 
another source, or move the disc out of the play position.
≥[DVD-A] 
Some discs contain bonus groups. If a password screen appears 
after selecting a group, enter the password with the numbered 
buttons to play the bonus group. Refer also to the disc’s jacket.
∫ When CD Mode is off (l18)
[DVD-A]
 [DVD-V] [VCD] [CD] [WMA] [MP3] [JPEG]
2Press the numbered buttons to select a 
group or title (
[WMA] [MP3] [JPEG] then press 
[ENTER]).
≥To select a 2-digit number
e.g. 23:[S10] l [2] l [3]
[WMA] [MP3] [JPEG]
 [2] l [3] l [ENTER]
≥[VCD] [CD] This step is unnecessary.
3Press the numbered buttons to select a 
chapter or track (
[WMA] [MP3] [JPEG] then press 
[ENTER]).
≥Repeat steps 2 and 3 to program other items.
4Press [1] (play).
∫ When CD Mode is on (l18)
[VCD] [CD] [WMA] [MP3]
2Press the numbered buttons to select a 
disc.
3Press the numbered buttons to select 
the items (
[WMA] [MP3] then press [ENTER]). 
≥To select a 2-digit number
e.g. 23:[S10] l [2] l [3]
[WMA] [MP3] [2] l [3] l [ENTER]
≥Repeat steps 2 and 3 to program other items.
4Press [1] (play).
Program/Random play
Each time you press [PLAY MODE] while 
stopped:
Program__--_--__--__--__--__--) Random
^------------------------ off (Normal play) (____}
∫Program play
When CD Mode is off
[DVD-A]
 [DVD-V] [VCD] [CD] [WMA] [MP3] [JPEG]
You can program all the items on a disc in the play position.
When CD Mode is on
[VCD] [CD] [WMA] [MP3]
You can program all the items on all the discs.
∫Random play
When CD Mode is off
[VCD] [CD]
You can play all the items on a disc in the play position in random 
order.
[DVD-A]
 [DVD-V] [WMA] [MP3] [JPEG]
You can play selected item on a disc in the play position in random 
order.
When CD Mode is on
[VCD] [CD]
 [WMA] [MP3] 
You can play all the items on all the discs in random order.
To exit 
Press [PLAY MODE] several times while stopped.
VOLUME
123
4
56
78
09CH
NAVI
CANCEL SPEED PROG
SKIPSLOW/SEARCH
MENU
ENTER
DIRECT 
NAVIGATOR
TOP MENU
RETURN
STATUS/
FUNCTIONS
TVFM/AM DVD/VHS
DV DTV
VHSTUNER
PICTURE MODE
SETUP
OPEN/CLOSE/EJECTJET REW
ENTER
PLAY 
LIST
TV VOL
TV VOLMULTI RE-MASTER QUICK OSDMIX 2CH 
ZOOMPROGRESSIVE 
CD MODEREPEAT
PLAY MODE
H.BASSSUBWOOFER LEVELC.FOCUS 
SFCTESTSUPER SRNDCH SELECTMUTING
CM SKIPADVANCE
DISC REVIEW
QUICK 
REPLAYREC
SLEEP
   PLAUDIORESET
TV/VIDEOSHIFT SHIFT
INPUT SELECTOR
SHIFT
PLAY MODE DVD
Numbered
buttons
CANCEL
ENTER
S10
MULTI 
RE-MASTER
DISC
REPEAT
PLAY MODE
∫ Program play (up to 32 items)
Program Playback
ENTERto select and pressPLAYto start
Disc No. T/G C/TPlayClearClear all
Choose a title and chapter.1
e.g. [DVD-V]
REC D.MIX RND
DTS PGMALL
PROG. DIGITALHDCD
ST MONO
dB
CHABCD
PL CTPG TGH.BASSTUNEDw
e.g. [CD]Disc No.
Track No.Program No.
RQT7921-P_ENG.book  20 ページ  ２００５年５月２５日　水曜日　午後３時２４分