Panasonic Dvd Vhs Home Theater Sound System Sc Ht820v Operating Instructions

							11
RQT7388
Attach the speaker-cable stickers to make connection easier.
[Note]
≥Never short-circuit positive (i) and negative (j) speaker wires.
≥Be sure to connect only positive (copper) wires to positive (i) terminals and negative (silver) wires to negative (j) terminals.
Incorrect connection can damage the speakers.
Caution
Hold the speakers by the sides. Applying pressure to the front net can damage the speaker.
STEP2Connecting speakers with the subwoofer
Speaker cables
≥3a4-m (13-foot) cables
(For Front and Center speakers)
≥2a10-m (33-foot) cables
(For Surround speakers)Sheet of speaker-cable 
stickers
2 Front (R)_:
`:
6 Subwoofer
1 Front (L)
4 Surround (R)
3 Surround (L)
5 Center
14352
_:
`:Copper
Silver Copper
Silver
Click!
Insert the 
wire fully.
Speaker-cable sticker
7388en.book  11 ページ  ２００３年１２月２２日　月曜日　午後９時３９分 
						

							12
RQT7388
To enjoy cable and satellite television
Connection ➜page 48
Subscribe to a cable or satellite company.If irregular coloring occurs on your television
The supplied speakers are designed to be used close to a 
television, but the picture may be affected with some televisions 
and setup combinations.
If this occurs, turn the television off for about 30 minutes.
The television’s demagnetizing function should correct the 
problem. If it persists, move the speakers further away from the 
television.
Basic connection
STEP3Te l ev i s i o n
75 ≠ coaxial cable
Video cable
AC IN
A
Y
P
B/CB
PR/CR
COMPONENT
VIDEO OUTS-VIDEO
OUTLINE
OUTLINE
IN VIDEO
OUT DVD/ 
VCR
VIDEO
IN EXT DVD
L
R
RF IN
RF OUTLOOPEXT
75
AM
ANTFM
ANTLOOPANT
GND
VIDEO
IN VHF/UHF
RF IN
Television
(not included)
Video cable
(included)
Antenna cable
(usually disconnected 
from the television) 75 ≠ coaxial 
cable
(included)
Cable TV
Outdoor antenna
Indoor antenna From If the connector 
doesn’t match 
➜page 49
If the connector doesn’t match 
➜page 49Main unit
Connect video cables directly to your television
The video signals on DVDs and videotapes have copyright 
protection. The video may not be shown correctly if you connect 
through an A/V selector or other equipment. 75 ≠ coaxial cable
This cable carries broadcast signals to the television whether the 
unit is on or off so you do not need to connect the antenna directly 
to the television.
It does not carry other signals from this unit, so make sure you 
connect the television to VIDEO OUT. Contact your dealer if your 
television does not have the corresponding terminal.
7388en.book  12 ページ  ２００３年１２月２２日　月曜日　午後９時３９分 
						

							13
RQT7388
∫Connecting a television with COMPONENT VIDEO terminals
COMPONENT VIDEO OUT terminal
These terminals can be used for either interlace or progressive 
output and provide a purer picture than the S-VIDEO OUT 
terminal. Connection using these terminals outputs the color 
difference signals (P
B/PR) and luminance signal (Y) separately in 
order to achieve high fidelity in reproducing colors.
≥The description of the component video input terminals depends 
on the television or monitor (e.g. Y/P
B/PR, Y/B-Y/R-Y, Y/CB/CR). 
Connect to terminals of the same color.
≥After making this connection, change the black level for a better 
picture (➜page 28, Video — Black Level Control).
To enjoy progressive video
≥Connect to the component video input terminals on a 480P 
compatible television. (Video will not be displayed correctly if 
connected to an incompatible television.)
≥All televisions manufactured by Panasonic and that have 480P 
input connectors are compatible. Consult the manufacturer if you 
have another brand of television.
∫Connecting a television with an S-VIDEO IN terminal
S-VIDEO OUT terminal
The S-video terminal achieves a more vivid picture than the VIDEO 
OUT terminal by separating the chrominance (C) and luminance 
(Y) signals. (Actual results depend on the television.)
[Note]
Connect to a different terminal group than that you used for the 
video cable (e.g., “VIDEO 2”).
Picture from this unit’s VHS will not appear when you use the same 
group input terminal connections because the S-video terminal 
input takes precedence.
For better video from DVD
The following connections are for video from the DVD section only. Make sure you have connected the VIDEO OUT terminal with the 
television to view video from the VHS section (➜page 12).
You may need to change the video-input mode on the television to view video from the VHS and DVD sections. Read your television’s  
operating instructions for details.
A
Y
P
B/CB
PR/CR
COMPONENT
VIDEO OUTS-VIDEO
OUTLINE
OUTLINE
IN VIDEO
OUT DVD/ 
VCR
VIDEO
IN EXT DVD
L
R
RF IN
RF OUTLOOPEXT
75
AM
ANTFM
ANTLOOPANT
GND
COMPONENT
VIDEO INY
P
B
PR
Video cables
(not included)
Television
(not included) To television
(➜page 12)
A
Y
P
B/CB
PR/CR
COMPONENT
VIDEO OUTS-VIDEO
OUTLINE
OUTLINE
IN VIDEO
OUT DVD/ 
VCR
VIDEO
IN EXT DVD
L
R
RF IN
RF OUTLOOPEXT
75
AM
ANTFM
ANTLOOPANT
GND
IN S VIDEO
S-video cable
(not included)
Te l ev i s i o n
(not included) To television
(➜page 12)
7388en.book  13 ページ  ２００３年１２月２２日　月曜日　午後９時３９分 
						

							14
RQT7388
Conserving power
The main unit consumes a small amount of power, even when it is 
turned off. The amount of power used depends on the display 
setting (➜page 40):
BRIGHT: 3.5 W DIM: 3.2 W OFF: 12.9 W
Audio memory backup
To save power when the unit is not to be used for a long time, 
unplug it from the household AC outlet.
You will need to reset some memory items after plugging the unit.
STEP4Radio and system connection
AC IN
A
Y
PB/CBPR/CRCOMPONENT
VIDEO OUTS-VIDEO
OUTLINE
OUTLINE
IN VIDEO
OUT DVD/ 
VCR
VIDEO
IN EXT DVD
LR
RF IN
RF OUTLOOPEXT
75
AM
ANTFM
ANTLOOPANT
GND
124
3
 System cable
AM loop antenna
FM indoor antenna2 AC power supply cords
Adhesive tape
Fix the other end of 
the antenna where 
reception is best. AM loop antenna
Stand the antenna up on its base.
Place the antenna where the 
reception is best.
Keep loose antenna cord away from 
other wires and cords.
System cable FM indoor antenna
Catch up
To disconnect
Press the catch 
and pull out.
Click! Connect the AC power supply cords after all other connections are complete.
Loosen the terminal 
with a Phillips-head 
screwdriver.
WhiteRedMain unit
Push and insert the 
antenna cables in as 
far as possible.Tighten the terminal 
screw again.Subwoofer
Catch up AC power supply cord
To household AC outlet 
(AC 120 V, 60 Hz)
To disconnect
Press the catch 
and pull out.
To household AC outlet 
(AC 120 V, 60 Hz) AC power supply cord
Black
AC power supply cords
Connect both AC power supply cords to enjoy all the features 
of this system.
Demo function
When the unit is first plugged in, a demonstration of its 
functions may be shown on the display.
If the demo setting is off, you can show a demonstration by 
selecting “DEMO ON” in the standby mode.
Press and hold [–DEMO] on the main unit.
The display changes each time you press and hold the button.
DEMO OFF()DEMO ON
While in the standby mode, select “DEMO OFF” to reduce 
power consumption.
7388en.book  14 ページ  ２００３年１２月２２日　月曜日　午後９時３９分 
						

							15
RQT7388
After plugging the unit into your household AC outlet and pressing 
[Í] to turn the unit on for the first time, the unit automatically tunes 
in all the channels it can receive and sets the clock.
The unit determines the type of transmission, TV or CATV, as 
follows:
TV: when there are less than 5 CATV channels.
CATV: when there are 5 or more CATV channels.
Preparation
≥Confirm that the antenna is connected correctly.
≥Turn on the television and select the video input for the VHS.
≥Press [VHS] to put the remote control in VHS mode.
Press [Í] to turn on the unit.
Plug-in Auto Tuning starts and the unit puts the stations it can 
receive into channels (➜page 39, Channel range).
The unit starts auto clock setting when finished, then displays the 
time.
[Note]
If auto tuning stops partway (by changing the source, turning the 
unit off, or due to a power failure.)
1 Disconnect the AC power supply cord on the main unit and then 
reconnect it.
2 Turn on the main unit.
To cancel partway
Press [MENU].
∫To start Plug-in Auto Tuning again (after 
relocation, for example)
Preparation
≥Press [Í] to turn on the unit.
≥Make sure there is no video cassette tape loaded in the unit.
≥Press [DVD/VHS] to select “VHS” as the source.
1 Press and hold [XCH] and [WCH] on the main unit 
simultaneously for 3 seconds until the channel changes to “2”.
2 Disconnect the AC power supply cord on the main unit and then 
reconnect it.
3 Turn on the main unit. Plug-in Auto Tuning restarts.
∫To set the channels manually (➜page 39).
∫If the unit couldn’t set the clock automatically
The MANUAL CLOCK SET screen appears. Set the time manually 
(➜page 38).
STEP5Plug-in Auto Tuning
VOLUME
123
456
78
0
100
9
CH
NAVI
CANCEL SPEED PROG
SKIPSLOW/SEARCH
MENU
ENTER
DIRECT 
NAVIGATOR
TOP MENU
RETURN
OSD/
DISPLAY
TVFM/AM DVD/VHS
DV D T V
VHSTUNER
DISC 1 DISC 2 DISC 3
DISC 4
PICTURE MODE
SETUP
OPEN/CLOSE/EJECTJET REW CD MODE
DISC 5
S10ENTER
PLAY 
LIST
TV VOL
TV VOLRESETTV/VIDEOPA G E
GROUPMIX 2CH
SUBTITLEREPEAT
PLAY MODE
MULTI RE-MASTER
SUBWOOFER LEVELC.S.M
SFCC.FOCUSSUPER SRNDPROGRESSIVEMUTING
POSITION
MEMORY ZOOM
QUICK REPLAYREC
SLEEP
   PLAUDIOTESTCH SELECTSHIFT
INPUT SELECTOR
OPEN/CLOSEEJECT DISC CHANGEDISC CHECKINPUT
SELECTORREC
/REW FF/STOP PLAYDOWNUPPHONES
CHVOLUMESTOP-DEMO
DISC
DISC
1 2 3 45
 1 2 3 4 5
PLAYPOWERÍ/I
Antenna system and channel captions all revert to the 
default values when you perform the procedure above. 
Reset the timer recording settings. (If necessary reset the 
clock first. ➜page 38, CLOCK SET)
AUTO CHANNEL SET
PROCEEDING
END :MENU2
Disappears     2
7388en.book  15 ページ  ２００３年１２月２２日　月曜日　午後９時３９分 
						

							16
RQT7388
∫TV maker setting
You can control the television by entering the remote control code.
1Refer the chart below for the code for 
your television.
2Aiming the remote control at the television
While pressing and holding [TV] ( ), 
press the numbered buttons to enter 
the code number.
≥Example: To select 01, press [0] ➜ [1].
≥The remote control outputs the on/off signal. If the code is 
correct, the equipment turns on or off. If it doesn’t, try 
entering another code.
[Note]
≥If your television brand is not listed or if the code listed for your 
television does not allow control of your television, this remote 
control is not compatible with your television.
≥Reenter the codes after you change the batteries.
∫TV operation
STEP6Operating the television
VOLUME
123
456
78
0
100
9
CH
NAVI
CANCEL SPEED PROG
SKIPSLOW/SEARCH
MENU
ENTER
DIRECT 
NAVIGATOR
TOP MENU
RETURN
OSD/
DISPLAY
TVFM/AM DVD/VHS
DV D T V
VHSTUNER
DISC 1 DISC 2 DISC 3
DISC 4
PICTURE MODE
SETUP
OPEN/CLOSE/EJECTJET REW CD MODE
DISC 5
S10ENTER
PLAY 
LIST
TV VOL
TV VOLRESETTV/VIDEOPA G E
GROUPMIX 2CH
SUBTITLEREPEAT
PLAY MODE
MULTI RE-MASTER
SUBWOOFER LEVELC.S.M
SFCC.FOCUSSUPER SRNDPROGRESSIVEMUTING
POSITION
MEMORY ZOOM
QUICK REPLAYREC
SLEEP
   PLAUDIOTESTCH SELECTSHIFT
INPUT SELECTOR
Operation Buttons
Power on/
standby[ÍTV]
Remote control 
TV mode[TV]
≥Switch the remote control mode to TV. Press 
before doing TV operations. When in TV 
mode, the [TV] button lights each time you 
press an operation button.
TV/Video switch [TV/VIDEO]
Selecting 
channels[WCH], [XCH] or numbered buttons 
[1–9, 100, 0,S10/ENTER].
≥[S10/ENTER] is used to confirm channel 
selection on some televisions manufactured 
by other companies.
Adjusting 
volume[TV VOLj] [TV VOLi]
TV
ManufacturerCode No.ManufacturerCode No.
Panasonic 01, 02 PHILIPS 06
FISHER14PIONEER02, 10, 19
G.E. 02, 03, 07, 09 QUASAR 02
GOLD STAR07, 15RCA03, 07, 09, 13, 23, 24, 25
HITACHI 05, 07 SANYO 14
JVC12SHARP08, 21
LXI 03, 06, 07, 10, 14, 15 SONY 04
MAGNAVOX06, 07, 11, 15, 22SYLVANIA06, 07, 15
MITSUBISHI 07, 15, 16, 21 SYMPHONIC 17
NEC07, 15TOSHIBA10, 21
PHILCO 06, 07 ZENITH 18, 20
7388en.book  16 ページ  ２００３年１２月２２日　月曜日　午後９時３９分 
						

							17
RQT7388
Turn on the television and select the video input for the DVD.
The QUICK SETUP screen assists you to make 
necessary settings such as:
≥Menu Language (➜page 29)
≥TV Type (➜page 28)
≥TV Aspect (➜page 28)
To change these settings later
Select “ QUICK SETUP” in “Others” tab (➜page 29).
STEP7DVD QUICK SETUP
VOLUME
123
456
78
0
100
9
CH
NAVI
CANCEL SPEED PROG
SKIPSLOW/SEARCH
MENU
ENTER
DIRECT 
NAVIGATOR
TOP MENU
RETURN
OSD/
DISPLAY
TVFM/AM DVD/VHS
DV D T V
VHSTUNER
DISC 1 DISC 2 DISC 3
DISC 4
PICTURE MODE
SETUP
OPEN/CLOSE/EJECTJET REW CD MODE
DISC 5
S10ENTER
PLAY 
LIST
TV VOL
TV VOLRESETTV/VIDEOPA G E
GROUPMIX 2CH
SUBTITLEREPEAT
PLAY MODE
MULTI RE-MASTER
SUBWOOFER LEVELC.S.M
SFCC.FOCUSSUPER SRNDPROGRESSIVEMUTING
POSITION
MEMORY ZOOM
QUICK REPLAYREC
SLEEP
   PLAUDIOTESTCH SELECTSHIFT
INPUT SELECTOR
1 234 5 6 7
Press to put 
the remote 
control in DVD 
mode.Turn on 
the unit.Select 
“DVD/
CD”.Shows QUICK 
SETUP screen.Follow the 
messages and 
make the 
settings.Press to 
finish QUICK 
SETUP.Press to exit.
DV DDVD/VHSSHIFT100
SETUP
iENTERENTERSHIFT100
SETUP
i
7388en.book  17 ページ  ２００３年１２月２２日　月曜日　午後９時３９分 
						

							18
RQT7388
Basic play
Turn on the television and select the appropriate video input for the DVD.
OPEN/CLOSEEJECT DISC CHANGEDISC CHECKINPUT
SELECTORREC
/REW FF/STOP PLAYDOWNUPPHONES
CHVOLUMESTOP DISCDISC
1 2
3 45
 1 2 3 4 5
PLAYPOWERÍ/IVOLUME
123
456
78
0
100
9
CH
NAVI
CANCEL SPEED PROG
SKIPSLOW/SEARCH
MENU
ENTERDIRECT 
NAVIGATOR
TOP MENU
RETURN
OSD/
DISPLAY
TVFM/AM DVD/VHS
DV D T V
VHSTUNER
DISC 1 DISC 2 DISC 3
DISC 4
PICTURE MODE
SETUP
OPEN/CLOSE/EJECTJET REW CD MODE
DISC 5
S10ENTER
PLAY 
LIST
TV VOL
TV VOLRESETTV/VIDEOPA G E
GROUPMIX 2CH
SUBTITLEREPEAT
PLAY MODE
MULTI RE-MASTER
SUBWOOFER LEVELC.S.M
SFCC.FOCUSSUPER SRNDPROGRESSIVEMUTING
POSITION
MEMORY ZOOM
QUICK REPLAYRECSLEEP
   PLAUDIOTESTCH SELECTSHIFT
INPUT SELECTOR
-DEMO
DV DPOWER
Í/I
STOP
PLAY
INPUT
SELECTOR
OPEN/CLOSE
DISC 1 2 3 4 5
2 Tu r n  o n  
the unit.
5 Open the disc tray and load 
the disc.
≥Load double-sided discs so the label for the 
side you want to play is facing up.
6 Close the disc tray.
≥A disc indicator lights green to show the tray 
is in the play position.
≥To load discs on the other trays, repeat steps 
4 and 6.
7 Start 
play.
Stop
3 Select 
“DVD/CD”. 1 Put the remote 
control in DVD 
mode.
Remote control signal sensor
4 Select the disc 
tray.
Disc indicators
8 Adjust the 
volume .
––dB N 0dB
(Minimum)
 (Maximum)
Progressive 
video
Stop
The position is memorized 
when “  ” flashes on the 
display.
≥Press [1] (PLAY) to resume. 
[DVD-V] To  r e v i e w  t h e  
previous chapters 
(➜page 20, Position 
memory)
≥Press [∫] to clear the 
position.
Pause≥Press [1] (PLAY) to start 
play.
Skip
(Group skip 
[WMA] [MP3] [JPEG])
SHIFT
PROGRESSIVEMUTING
i
PROG.
OPEN/CLOSE/EJECT
SKIP
ENTER
Select
Register
Search
(during play)≥Up to 5 steps
≥Press [1] (PLAY) to start 
play.
Slow-motion
(during pause)≥[VCD] Slow motion, forward 
direction only
Frame-by-
frame
(during pause)≥[VCD] forward direction only
On-screen 
item select
Enter number
[RAM] [DVD-A] [DVD-V] [VCD] [CD]
e.g. To select 12:
[S10] ➜ [1] ➜ [2]
[VCD] with playback control 
While stopped, press the 
numbered buttons. 
[WMA] [MP3] [JPEG]
e.g. To select 123:
[1] ➜ [2] ➜ [3] ➜ [ENTER]
≥Press [CANCEL] to cancel 
the number(s).
SLOW/SEARCH
ENTER
ENTER
Select
Register
123
456
78
09
S10ENTER
CANCEL
DVD
7388en.book  18 ページ  ２００３年１２月２２日　月曜日　午後９時３９分 
						

							19
RQT7388
DISC 1 2 3 4 5
[Note]
Discs continue to rotate while menus are displayed. Press [∫] when 
you finish to preserve the unit’s motor and your television screen.
VOLUME
123
456
78
0
100
9
CH
NAVI
CANCEL SPEED PROG
SKIPSLOW/SEARCH
MENU
ENTER
DIRECT 
NAVIGATOR
TOP MENU
RETURN
OSD/
DISPLAY
TVFM/AM DVD/VHS
DV D T V
VHSTUNER
DISC 1 DISC 2 DISC 3
DISC 4
PICTURE MODE
SETUP
OPEN/CLOSE/EJECTJET REW CD MODE
DISC 5
S10ENTER
PLAY 
LIST
TV VOL
TV VOLRESETTV/VIDEOPA G E
GROUPMIX 2CH
SUBTITLEREPEAT
PLAY MODE
MULTI RE-MASTER
SUBWOOFER LEVELC.S.M
SFCC.FOCUSSUPER SRNDPROGRESSIVEMUTING
POSITION
MEMORY ZOOM
QUICK REPLAYREC
SLEEP
   PLAUDIOTESTCH SELECTSHIFT
INPUT SELECTOR
OPEN/CLOSEEJECT DISC CHANGEDISC CHECKINPUT
SELECTORREC
/REW FF/STOP PLAYDOWNUPPHONES
CHVOLUMESTOP-DEMO
DISC
DISC
1 2
3 45
 1 2 3 4 5
PLAYPOWERÍ/I
DISC1–5< DISC CHANGE
DISC CHECK
[DVD-A] [DVD-V]
Shows a disc top menu
Disc menu
[DVD-V]
Shows a disc menu
[VCD]
Shows a disc menu
Return to 
previous 
screen
Information 
screen[WMA] [MP3] [JPEG]
Turns the information screen 
on/off
Starting play 
from a 
selected 
group
[DVD-A] [WMA] [MP3] [JPEG]
A folder on WMA/MP3 and JPEG discs is 
treated as a “Group”.
NAVI
TOP MENU
MENU
RETURN
RETURN
MIX 2CH
SUBTITLE
PA G E
GROUP
ENTER
RegisterSelect
Selecting the 
disc directly
≥You can select the disc with 
[DISC1–5] on the main unit.
Checking the 
disc trays
All discs except the disc in 
play open without interrupting 
play. While stopped, all trays 
will open.
≥Press [DISC CHECK] again 
to close the trays.
≥Do not pull out the trays, 
remove, or insert discs 
during the disc check.
Changing the 
discs during 
play
You can change the other 
discs without interrputing play.
≥After selecting the disc tray, 
press [< DISC CHANGE] to 
close the tray.
SHIFT
123
45DISC 1 DISC 2 DISC 3
DISC 4 DISC 5i
DISC CHECK
(Main unit)
DISC CHANGE
(Main unit)
If you are experiencing problems, refer to troubleshooting 
(➜ pages 50–52).
[Remember] Press [DVD] first.
7388en.book  19 ページ  ２００３年１２月２２日　月曜日　午後９時３９分 
						

							20
RQT7388
Convenient functions
See below for details.
(Only when the elapsed play time can be displayed
[JPEG]: Works with all JPEG content)
This position is memorized even after turning off the unit, changing 
the source or moving the disc out of the play position.
Press [POSITION MEMORY].
≥Up to 5 discs.
≥When the sixth disc is memorized, the earliest position is replaced.
≥You cannot recall the position in CD Mode (➜page 21).
When the unit is turned on, “DVD/CD” is reselected or the disc 
comes to the play position, 
Press [1] (PLAY) to start play from that 
position.
To review the previous chapters [DVD-V]
Press [1] (PLAY) while the following message is displayed.
Do not press [1] (PLAY) if you want to cancel review.
[RAM]
 [DVD-V] [VCD]
Press [ZOOM] several times to select the 
preset aspect ratio or “Auto”. (Just Fit 
Zoom)
Fine adjustments (Manual Zoom)
Press [21].
–from k1.00 to k1.60 (in 0.01 units)
–from k1.60 to k2.00 (in 0.02 units)[DVD-V] (with multiple subtitles) [VCD] (SVCD only)
[RAM] (On/Off only)
Press [SUBTITLE] several times to select 
the subtitle language.
To clear/display the subtitles
Press [21] to select “On” or “Off ”.
[DVD-A]
 [DVD-V] (with multiple soundtracks) [RAM] [VCD]
Press [SHIFT]i[AUDIO] 
several times to select 
the soundtrack.
[RAM] [VCD]
You can use this button to select “L”, “R” or “LR”.
[DVD-V] (Karaoke discs)
Press [21] to select “On” or “Off ” of vocals.
Read the discs instructions for details.
Signal type/data
LPCM/PPCM/ÎDigital/DTS/MPEG: Signal type
kHz (Sampling frequency)/bit/ch (Number of channels)
Example:
3
/2 .1ch
Position memory
Memorizes the position to resume play.
Zoom
Expands the letterbox picture to fit the screen.
Subtitle
Changes the subtitle language.
Audio
Changes the soundtrack.
VOLUME
123
456
78
0
100
9
CH
NAVI
CANCEL SPEED PROG
SKIPSLOW/SEARCH
MENU
ENTER
DIRECT 
NAVIGATOR
TOP MENU
RETURN
OSD/
DISPLAY
TVFM/AM DVD/VHS
DV D T V
VHSTUNER
DISC 1 DISC 2 DISC 3
DISC 4
PICTURE MODE
SETUP
OPEN/CLOSE/EJECTJET REW CD MODE
DISC 5
S10ENTER
PLAY 
LIST
TV VOL
TV VOLRESETTV/VIDEOPA G E
GROUPMIX 2CH
SUBTITLEREPEAT
PLAY MODE
MULTI RE-MASTER
SUBWOOFER LEVELC.S.M
SFCC.FOCUSSUPER SRNDPROGRESSIVEMUTING
POSITION
MEMORY ZOOM
QUICK REPLAYREC
SLEEP
   PLAUDIOTESTCH SELECTSHIFT
INPUT SELECTOR
PROG POSITION
MEMORY
SPEEDZOOM
MIX 2CH
SUBTITLE
SHIFTCANCELAUDIOr
Position memory
Zoom
Position memorized
Press PLAY to Preview Chapters
 Menu
Just Fit Zoom            ˜1.00
Subtitle
Audio
.1: Low frequency effect
.1:(not displayed if there is no signal)
.0: No surround
.1: Mono surround
.2: Stereo surround (left/right)
.1: Center
.2: Front leftiFront right
.3: Front leftiFront rightiCenter
 Menu
Subtitle Off
 Menu
Audio          1
DVD
7388en.book  20 ページ  ２００３年１２月２２日　月曜日　午後９時３９分