Panasonic Dvd Vcr DeckPv D4761 Operating Instructions
Have a look at the manual Panasonic Dvd Vcr DeckPv D4761 Operating Instructions online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 10737 Panasonic manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
[email protected] Insert a tape with a record tab (p. 6). 1DECK power comes on. The VCR mode and “VCR” Indicator light up on Multi Function Display. 5 4 2 3 Press CH /, or NUMBER keys to select the channel. For “LINE” input, see p. 39. If channels is over 100, press 100 key then press the remaining 2 digits. Press SPEED to select the record speed (p. 6). SP = Standard Play LP = Long Play SLP = Super Long Play Press REC to start recording. (The VCR REC Indicator lights up on Multi Function Display), To edit out unwanted scenes, press PAUSE/STILL to pause, and again to resume recording. Press STOP to stop recording. It is not possible to record from DVD/ Video CD/CD to VHS tape using DECK. Watching one channel and recording another is not possible when using Cable Box or DSS Receiver. After 5 minutes in Pause mode, DECK stops to protect a tape and video heads. One Touch Recording (recording in progress),-->Press REC repeatedly to set the recording length (30 min. ~ 4 hours). DECK shuts off after the preset record length. Record one station, watch another,-->press VCR/TV (“VCR” goes out on Multi Function Display), --> select channels at TV (recording continues). Select channels at DECK,-->press VCR/TV (“VCR” lights up on Multi Function Display), --> select channels at DECK. Play a disc while recording a tape.--> insert a disc during recording, -->press DV D, and then press PLAY. Speed appears on-screen and on Multi Function Display. You cannot view another channel during recording. Basic Operation Notes*Important:If a remote control button does not work when pressed, press the VCR button on the remote and try the button again. Record on a Tape Note Remove loose or peeling labels from tapes to prevent tape jam. Multi Function Display Record using DECK buttons 4 2 Select Channel. VCR/TV Press REC to start Recording. Press STOP/EJECT to stop. This video recorder, equipped with HQ (High Quality) system, is compatible with existing VHS equipment. Only use tapes with the mark. Only tapes tested and inspected for use in 2, 4, 6, and 8 hour machines are recommended. Normal Rec0:301:00 1:302:003:004:00 1Insert a tape.
22For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected] T I TLE MENU Cas t l es Love r s Dogs B i r ds 5Press orNUMBER keys (see below) to select title, and press SETto play. Basic DVD Operation Ready Checklist All connections are made. (pp. 12 ~ 15) DECK is plugged in. If DECK is connected to an audio amplifier, turn the stereo system’s power on.1Press POWER* on the remote or DECK. Press DVD to select DVD mode. Press OPEN/CLOSE, and then place a disc into the disc tray. 2 3If a disc is already inserted, go to step 4. (Depending on the disc, playback may start automatically.) Press PLAY to start playing. Disc tray closes automatically. 4 12 If an interactive DVD*1 or a Video CD with playback control* 2 is used and TITLE MENU appears, go to step 5.You may also close tray by pressing OPEN/CLOSE. Data reading time differs with each disc. * 1Interactive DVD... May include multiple camera angles, stories, etc. * 2Video CD with playback control... Particular scenes or information can be interactively selected from a menu that appears on the screen. Operation using DECK buttons Press PLAY. Insert a disc. Press OPEN/CLOSE. Press STOP. 6Press POWERUsing NUMBER keys starts playing automatically. 1 digit number 1 1 2 digit number 12 10 1 2 3 digit number 123 100 1 2 3 Press SKIP | or | to go to next or previous menu screen. SKIP function not available with all discs. Please refer to disc jacket for operation information. To return to menu (play stops)Press TITLE, MENU, or RETURN. (DVD) Press RETURN. (Video CD) Press STOPto stop playing.6 7 Press OPEN/CLOSEto eject the disc. 4 1 33 7 OPEN/ CLOSE 10 MENU SETFF/ SLOW+ STOP RETURN POWER REW/ SLOW- NUMBER keys TITLE PLAYDVD PAUSE/ STILL SKIP SKIP Hold disc by its edges only (p. 4) with printed side up and use guides to place into tray. Use 3”(8 cm) or 5” (12 cm) disc. 2 1 SELECT CLOSE READING T I TLE MENU Cas t l es Love r s Dogs B i r ds Dogs of the world SURROUND
[email protected] Basic Operation (DVD) Please read the disc jacket for operation information. If a single sided disc is placed in upside down, “PLEASE CHECK THE DISC, AND FOR STAINS OR SCRATCHES ON DISC” is displayed. Remove a disc and press DECK POWER off when not in use. Disc continues to rotate with menu displayed even after play is done. Press STOP to clear menu display when finished with menu. Forward/Reverse Scene Search Press FF/SLOW+ or REW/SLOW-during Play mode. Press PLAY to release. Starting forward/reverse search during Play mode started from menu on Video CDs may recall menu. Search speed, slow at first, increases with each additional press of the button up to 5 levels. Forward/Reverse Chapter/Track Skip Press SKIP | or | during Play mode. Each press SKIPs a chapter (DVD) or track (Video CD/CD). Pressing | SKIP once midway through a chapter/track returns to start of that chapter/track. Each additional press skips back one chapter/track. Pressing SKIP | or | during Play mode started from menu on Video CDs may recall menu. Still Picture or Pause Press PAUSE/STILL during Play mode. Press PLAY to release. DVD/Video CD : DECK will enter Still mode. CD : DECK will enter Pause mode. Frame by Frame Picture (DVD/Video CD) Press PAUSE/STILL in Still mode. Press PLAY to release.Each press advances picture one frame. Hold button down for consecutive frame advance. Whether pictures are advanced by “FRAME” or “FIELD” is selected automatically. (See p. 51.) Slow Motion Picture (DVD/Video CD) Press FF/SLOW+ or REW/SLOW- in Still mode. Press PLAY to release. Slow motion speed, slow at first, is increased with each additional press of the button up to 5 levels. Reverse slow motion is not available for Video CDs. When appears on the screen while a button is being operated, it means that the corresponding operation is prohibited by DECK or the disc.DECK memorizes the point where STOP is pressed ( flashes on screen). Press PLAY to resume play from this point. Pressing STOP again or opening the tray cancels RESUME, however, RESUME is not canceled when power is turned off and on. RESUME works only with discs for which elapsed play time is displayed during playing. Resume Function Notes Power turns off after DECK has been in Stop mode (DVD) for about 5 minutes. Auto-Power Off Function 1. Do steps 1 ~ 4 (previous page). When menu appears, press STOP. 2.Press NUMBER keys to select desired track (play begins). Check the disc for track numbers. Press “1” to start at beginning of the disc. To Resume Menu use,Press STOP and press PLAY, then MENU. Now, go to step 5 (previous page). Enjoy Video CDs featuring playback control without using menus (Video CDs only) *Important:If a remote control button does not work when pressed, press the DVD button on the remote and try the button again. Surround Sound System Press SURROUNDto set Surround sound. To cancel, press SURROUND. Surround sound effects is available in DVD mode only. Note SURROUND ON SURROUND OFF Reverse Skip Forward SkipCurrent playback position Chapter/Track Chapter/Track Chapter/TrackChapter/Track
24For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected] Timer Recording ADD/DLT Press PROG/VCR+ button* to display “SET PROGRAM.” Press PROG/VCR+ button to end programming. 43 1 DAILY 131 31 12 SELECT / Selection Order WEEKLY (SAT)WEEKLY (MON) WEEKLY (SUN) 14 Example Today 2) To set remaining items, press to select and press SET to set START/ STOP times, CH(channel) or LINE input (p. 39), and tape speed (SP, LP, SLP). Press PROG/VCR+ button to exit. To Enter More Programs, press to select and press SET to set an unused program number and repeat step 3. Or SET PROG/ VCR+ 2Press to select “TIMER PROGRAMMING” and press SET to display Program screen. SELECT T I MER PROGRAMM I NGVCR Plus + PROGRAMMING SELECT : SET : SET EXIT : PROG SET PROGRAM SESELE CT START START DATATE 1313 SUN SUN --:-- --:-- --:-- --:-- ----TODAY DATE START ST OPCH SLP SELE CT : SET : SET END : PROG - - - - - - - - -- - - - - - - -- - - - - - - P DT START STOP CH SPD 1 1 13 1013 10 : 0000 P 1212 : 0000 P 02 SPSP2 -- -- : -- -- : -- -- --3 -- -- : -- -- : -- -- --4 -- -- : -- -- : -- -- --CANCEL : ADD / DLT SELECT 1-8 : ENTER : SET EXIT : PROG Ready Checklist All connections are made (pp. 12 ~ 15).TV and DECK are plugged in.Clock set correctly.Tape has rec.tab. (p. 6)Remote is in VCR mode. (Press VCR.)Sufficient tape remaining for rec time. 1) To set record DATE, press to select: 1~31= one time, or DAILY= MON ~ FRI, or WEEKLY= same time each week, and press SET. See selection order left. VCR REC Indicator VCR mode Indicator A M VCR VCR RECDVD ANGLEVCR Hi-FiTIMER Multi Function Display The “Timer” Indicator lights up on DECK. You can do Timer Recording either power off or power on. • “TIMER REC WILL START SOON” appears on-screen for 2 minutes before Timer Recording star t. If DECK is in DVD mode, no message appears, but the VCR REC Indicator, the VCR mode Indicator and “REC” will flash on Multi Function Display.TIMER Indicator
[email protected] To Replace program... To Clear program... Review, Replace or Clear Program Contents: (Recording is not in progress) or CANCEL : ADD / DLT SELECT 1-8 : ENTER : SET EXIT : PROG P DT START STOP CH SPD1 7 9 : 00A 12 : 00A 08 SP2 8 10 : 00P 12 : 00P 02 SP3 10 8 : 00P 9 : 00P 10 SP4 SU 9 : 00P 10 : 00P L1 LP CANCEL : ADD / DLT SELECT 1-8 : ENTER : SET EXIT : PROG P DT START STOP CH SPD1 -- -- : -- -- : -- -- --2 8 10 : 00P 12 : 00P 02 SP3 10 8 : 00P 9 : 00P 10 SP4 SU 9 : 00P 10 : 00P L1 LP Press ADD/DLT. *Important:If a remote control button does not work when pressed, press the VCR button on the remote and try the button again. 1 3 4 Press to select number and press SET to display. To cancel Timer Recording in progress... Repeat Step 3 (p. 24) to set new programs. Press PROG/VCR+ button to end the program.Hold down STOP on VCR mode for a few seconds to cancel Timer Recording. (The “TIMER” indicator goes out on Multi Function Display.) Any future daily or weekly recording will be performed as programed. NotesRepeat steps 1 ~ 2 on page 24. 2 7 SUN SUN 9 9:00A00A 1212: 00A00A 08 08 TODAY---------------------------------------- DATE START STOP CH SPSESELE CT START START DATATE SELECT : SET : SET BACK :END : PROG If you are using Cable Box, the VCR’s channel for Timer Recording must be set to the Cable Box output channel and Cable Box must be manually set to the desired channel. Cable Box power must be left on. 2 minutes before Timer Recording is performed, “PLEASE PREPARE FOR TIMER REC” appears and Timer Indicator flashes. Be sure a cassette with record tab is loaded and DECK is in Stop mode. If a power interruption occurs while programming the timer, the timer program(s) may be canceled. If “TIMER PROGRAMS WERE LOST DUE TO POWER INTERRUPTION” appears on-screen, please reenter the timer programs. If the star t time for Timer Recording comes up during recording and playing back, Timer Recording will not be performed. Important notes when using DSS Receiver When recording programs via DSS Receiver, DSS Receiver must be left on. When recording programs via an antenna or cable, DSS Receiver must be turned off. VCR Operation
26For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected] 1 In order for VCR to read PlusCode numbers, some setup is required. Guide channel numbers are assigned to each local broadcast and cable station. Because this number sometimes differs from the channel your TV receives the station on, it is necessary to program the VCR with local channel information. To receive VCR Plus+ channels automatically, perform the steps below. Or, see “Manual VCR Plus+ System Channel Setup” section on p. 28. Important Note “Initial Setup” on pp. 16, 17 must be completed before “Auto VCR Plus+ System Channel Setup” can be done. If any part of setup is incomplete, a warning screen appears. When Auto Set is performed, channels set in initial setup (pp. 16, 17) will be replaced by automatically downloaded data. Make each entry within 5 minutes, or VCR will leave this mode. Once local channels have been programmed, they will stay in memory, even in the case of a power failure. If the start time for Timer Recording comes up during Auto VCR Plus+ System Channel Setup, the Timer Recording will have priority. NotesVCR Plus+ System is ... a feature that allows you to set most items of Timer Recording by simply entering a special code number (PlusCode programming number) found in TV GUIDE and selected newspaper TV listings. 2 3 4 5 6 7 Auto VCR Plus+ System Channel Setup (Part 1) Press ACTION* to display menu. Press to select “SET UP CHANNEL” and press SET. Press to select “VCR Plus+ CH SET UP” and press SET to display. Make sure to leave VCR off (overnight). Press ACTION to end. Press to select When to Update and press SET. Press to enter “ZIP CODE” and enter each number. Press SET or ACTION to set.Press to select “AUTO SET” and press SET. Timer Recording Using VCR Plus+ System ACTION SET SELECT SELECT : EXIT : ACTION SET:SET MENU SET UP DVD SET UP VCR SET CLOCK SET UP CHANNEL IDIOMA/LANGUE : ENGLISH VCR’S OUTPUT CH:3 SELECT : EXIT : ACTION SET : SET MENU SET UP DVD SET UP VCR SET CLOCK SET UP CHANNEL IDIOMA/LANGUE : ENGLISH VCR’S OUTPUT CH:3 ANTENNA : CABLE AUTO SETWEAK SIGNAL DISPLAY : OFFCABLE/DSS BOX SET UP VCR Plus+ CH SET UP SELE CT : SET : SET EXIT : ACT I ON SET UP CHANNEL AUTO SET MANUAL SELE CT : SET : SET EXIT : ACT I ON VCR Plus+ CH SET UP PLEASE ENTER Z I P CODE Z I P CODE : ----- SELECT : SET : SET END : ACT I ON VCR Plus+ CH SET UP SELECT : SET : SET EXIT : ACT I ON PLEASE SELECT HOW OFTEN TO UPDATE R I GHT NOW EVERY NIGHT EVERY MONDAY NIGHT END : ACT I ON PLEASE LEAVE VCR OFF (OVERNIGHT) VCR Plus+ CH SET UP
[email protected] Auto VCR Plus+ System Channel Setup (Part 2) Press to select channel map for your area and press SET. Before you perform the following steps, you should have: completed “Auto VCR Plus+ System Channel Setup (Part 1)” on p. 26. left VCR off overnight, and turned it back on after 9:00 AM the next day. If channel updatingwas successful...If VCR could notdistinguish channel map... Press ACTION to exit this mode.Press ACTION to display “SELECT VCR Plus+ CH” Continue with step 2. To Change or Update Auto VCR Plus+ System Channel Setup (E.g. you selected wrong channel map or zip code.) aDo “Auto VCR Plus+ System Channel Setup (Part 1)” steps 1 ~ 4 on p. 26. bPress to select “UPDATE VCR Plus+ CH” or “SELECT VCR Plus+ CH,” then press SET. cIf you selected “UPDATE VCR Plus+ CH,” perform steps 5 ~ 7 in the “Auto VCR Plus+ System Channel Setup (Part 1)” section on p. 26. If you selected “SELECT VCR Plus+ CH,” perform steps 2 ~ 3 in the “Auto VCR Plus+ System Channel Setup (Part 2)” section on this page. Press ACTION to end. Make sure to leave VCR off (overnight). Repeat these steps as necessary. If Auto Setup fails, do “Manual VCR Plus+ System Channel Setup” on p. 28. Channel map will be updated (overnight). If it was successful, “VCR Plus+ CH SET COMPLETED” appears on screen. And then, press ACTION to exit. 1 2 3 *Important:If a remote control button does not work when pressed, press the VCR button on the remote and try the button again. END : ACT I ON VCR Plus+ CH SET COMPLETEDVCR Plus+ CH SET UP NEXT : ACT I ON PLEASE SELECT VCR Plus+ CHANNELVCR Plus+ CH SET UP SELECT VCR Plus+ CH KABC CNN ESPN KNBC 12 13 14 15 51 42 18 33 1 5 10 7 101 99 110 78 SELE CT : SET : SET EXIT : ACT I ON ---------------------------------------- END : ACT I ON PLEASE LEAVE VCR OFF (OVERNIGHT) VCR Plus+ CH SET UP UPDATE VCR Plus+ CHSELECT VCR Plus+ CH SELE CT : SET : SET EXIT : ACT I ON VCR Plus+ CH SET UP VCR Operation
28For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected] GUIDE CH RECEIVE CH01 --02 -- VCR Plus+ CH SET UP CLEAR :ADD/DLT SELECT : SET:SET EXIT : ACTION To enter VCR Plus+ channels, Manual VCR Plus+ System Channel Setup 5 2 3 1 Initial Setup.....In order to use Timer Recording Using VCR Plus+ System, the Initial Setup on pages 16, 17 must be completed for setting Clock and Channel. Channel Setup.....Since numbers assigned to channels found in TV Guide and selected newspapers may differ from channels in your viewing area, you’ll need to enter your local TV channel number for each corresponding Guide Channel. If you perform the VCR Plus+ Channel set up procedures shown below, you will be able to perform timer recordings using the PlusCode programming number listed in your local TV listing. 6 Assigned Guide channel No. 15 20 04 Broadcast or Cable station name HBO Nickelodeon CBS FOX SAMPLE ONLY 33 38 04 11 Channel No. on which my TV receives the station. 4 For [VCR-TV] or [VCR-Cable Box-TV] connection only. Timer Recording Using VCR Plus+ System (continued) Press ACTION three times to end setup.To Make Corrections, press and SET to move to error, then to change, or ADD/DLT to erase number. Press ACTION* to display menu. Press to select “VCR Plus+ CH SET UP,” and press SET. press to scroll up/down, and press SET to move cursor to right, then press to enter number, and press SET to set and move cursor to left. Repeat step 5 until list is complete. Press to select “MANUAL,” and press SET. To complete step 5 of setup, do the following: Prepare a TV/Cable station line-up and channels they are received on. Also, the Guide channel numbers assigned to your stations (found in TV Guide and selected newspapers). Make a 3-column chart (see sample). Left column --> all stations you receive. Middle column --> each station’s assigned Guide channel number from TV Guide, etc. Right column --> channel number on which your TV receives the station. Press to select “SET UP CHANNEL” and press SET. SELECT : EXIT : ACTION SET:SET MENU SET UP DVD SET UP VCR SET CLOCK SET UP CHANNEL IDIOMA/LANGUE : ENGLISH VCR’S OUTPUT CH:3 SELECT : EXIT : ACTION SET : SET MENU SET UP DVD SET UP VCR SET CLOCK SET UP CHANNEL IDIOMA/LANGUE : ENGLISH VCR’S OUTPUT CH:3 ANTENNA : CABLE AUTO SETWEAK SIGNAL DISPLAY : OFFCABLE/DSS BOX SET UP VCR Plus+ CH SET UP SELE CT : SET : SET EXIT : ACT I ON SET UP CHANNEL AUTO SET MANUAL SELE CT : SET : SET EXIT : ACT I ON VCR Plus+ CH SET UP GUIDE CH RECEIVE CH 01 --02 -- VCR Plus+ CH SET UP
[email protected] To Make Corrections, press repeatedly to delete number, then repeat step 3. Press PROG/VCR+ button to display “SET PROGRAM.” Press PROG/VCR+ button to end program. Press to select record speed, and press SET. 3 2 1 4 5 6 Do normal Timer Record if... PlusCode number is not listed for program. the program (e.g. sports event) may run over set stop time. See p. 25 to: cancel Timer Recording in progress. review, replace, or clear program contents. Important for DSS/ Cable Box Users When recording via DSS, the receiver must be left on. When recording via cable or antenna, DSS Receiver must be off. When recording via Cable Box, leave the box on. Notes Ready Checklist Clock is set. VCR Plus+ Setup is complete (see pp. 26 ~ 28). Press ADD/DLT to delete the program. If the PlusCode number entered begins with “0”, skip to step 5. Display in step 4 will not appear. *Important:If a remote control button does not work when pressed, press the VCR button on the remote and try the button again. ADD/DLT NUMBER keys SET ACTION PROG/ VCR+ VCR Plus+ System Programming Press NUMBER keys to enter PlusCode number and press SET. Press PROG/VCR+ button to exit. Do not overlap program times. PlusCode numbers cannot be used to program VCR to record DSS and Cable Box channels. Make each entry within 1 minute or the VCR will exit setup mode. Once VCR Plus+ Channel Setup is done, channels stay in memory. If a power interruption occurs, VCR Plus+ Channel Setup may be lost. Please do VCR Plus+ Channel Setup again. (continued) Press to select “ONCE,” “DAILY (MON ~ FRI),” or “WEEKLY” record frequency and press SET. Obtain unlisted PlusCode numbers by calling 1 - 900 - 454 - 7587. Call costs about $.95 per minute. Press to select “VCR Plus+ PROGRAMMING” and press SET to display VCR Plus+ screen. SELECT T I MER PROGRAMM I NGVCR Plus + PROGRAMMING SELECT : SET : SET EXIT : PROG SET PROGRAM SET : SET ENTER PLUSCODE NUMBER USING 0 - 9 KEYSBACKSPACE : 1 VCR Plus+ SYSTEM SELECT : SET : SET ONCEDAILY(MON-FRI) WEEKLY VCR Plus+ SYSTEM 8 SAT SAT 1010:0000P P 1212: 0000P 0202DATE START STOP CH SPSESELE CT RECORD SPEED RECORD SPEEDSELECT : SET : SET BACK : END : PROG TODAY- - - - - - - - -- - - - - - - -- - - - - - - P DT START STOP CH SPD 1 1 8 8 10 10 : 0000 P 1212 : 0000 P 02 SPSP2 -- -- : -- -- : -- -- --3 -- -- : -- -- : -- -- --4 -- -- : -- -- : -- -- --CANCEL : ADD / DLT SELECT 1-8 : ENTER : SET EXIT : PROG Although you can do Timer Recording either power off or on, you’ll need to turn power off for Auto Set of “VCR Plus+ CH SET UP” except watching a disc. (See p. 26). VCR Operation
30For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected] MONO broadcast Normal monaural sound broadcast. SAP broadcast Secondary Audio Program (sub language) broadcast. Select SAP audio mode for the sub language. MTS Stereo broadcast Multi-channel Television Sound Stereo broadcast. Select STEREO audio mode. If stereo broadcast is weak and display flickers, select MONO audio mode for possible better results. MTS Stereo and SAP broadcast Multi-channel Television Sound Stereo (main language) and Secondary Audio Program (sub language) broadcasts are being received simultaneously. Select STEREO or SAP audio mode. The following are possible audio broadcast types and on- screen displays. The signal being received is indicated with an “ ” mark while the selected audio mode is indicated with an arrow. Receivable Broadcast Types MTS Broadcast/ VHS Hi-Fi Stereo System Equipped with ®-TV Noise Reduction for true MTS reproduction. ®-TV Noise Reduction is required for good stereo separation and audio fidelity. ® is a registered trademark, and is licensed by ® Technology Licensing. DISPLAY Connection Make the Audio/Video Connection as shown on pp. 12 ~ 15. You can use TV connected to a Stereo amplifier and speakers instead of Stereo TV. To display the broadcast signal being received, --> press DISPLAY* . STOP 1 2 : 0 0AMABC 0 : 0 0 : 0 0 SPSTEREOSAPMONO STOP 1 2 : 0 0AMABC 0 : 0 0 : 0 0 SPSTEREOSAPMONO STOP 1 2 : 0 0AMABC 0 : 0 0 : 0 0 SPSTEREOSAPMONO STOP 1 2 : 0 0AMABC 0 : 0 0 : 0 0 SPSTEREOSAPMONO AUDIO(SAP/Hi-Fi)