Panasonic Dmr Ez48 Operating Instructions Manual

							51
RQT9056
[RAM] [-R] [-R]DL] [-RW‹V›] [+R] [+R]DL] [+RW] [DVD-V] [-RW‹VR›] and 
DivX
Picture
[RAM] [-R] [-R]DL] [-RW‹V›] [+R] [+R]DL] [+RW] [DVD-V] [-RW‹VR›]
Set picture mode
Normal:  Default setting
Cinema:    Mellows down movies, enhances detail in dark 
scenes.
DNR (Digital Noise Reduction)
[RAM] [-R] [-R]DL] [-RW‹V›] [+R] [+R]DL] [+RW] [DVD-V] [-RW‹VR›] and 
DivX
“On” reduces noise and picture degradation.
Progressive
¹ (Progressive/24p²) 
Select the method of conversion for progressive output to suit 
the type of material being played.
Auto1 (normal):   Film and video contents are detected 
automatically and converted properly.
Auto2:  When using “Auto1” and video content is 
distorted as shown below.
 
24p²:  [DVD-V] When this unit is connected to a TV supporting 
1080/24p output via an HDMI cable, this unit displays 
each frame at 1/24 second intervals – the frame interval 
originally recorded in the  lm, thus faithfully reproducing 
the original cinema image.
If the settings are changed, then the screen will darken 
for a few seconds and then playback will start.
“Auto1” is set when you turn the unit off or open disc tray.
¹ Only when you have selected “480p” or higher for 
“Component Output Signal” (
						

							52
RQT9056
DVD and Card Management
Accessing the Management Menus
  ,  to select “Other Functions” 
then 
OK
DVD-RAMFUNCTIONS Cartridge Protection Off
Disc Protection Off
Other Functions
Program
Copy
OKdelete
PlaybackPlaylists
Flexible Recording
DV Camcorder Rec.
Setup
DVD Management
  ,  to select “DVD 
Management” or “Card 
Management”, then 
OK
[SD] The only menu available in “Card 
Management” is “Format memory card”.[RAM] [-R] [-R]DL] [-RW‹V›] [+R] [+R]DL] [+RW] 
Perform preparation steps 14 of “Accessing the 
Management Menus” (
						

							53
RQT9056
[RAM] 
Perform preparation steps 14 of “Accessing the 
Management Menus” (
						

							54
RQT9056
DVD and Card Management
  OK to complete.
[-R] [-R]DL] [-RW‹V›] [+R] [+R]DL] 
You can play these discs on compatible DVD players by 
 nalizing it on the unit.
The menu you create with the unit can also be used on 
most DVD players.
Perform preparation steps 14 of “Accessing the 
Management Menus” (
						

							55
RQT9056
Setup Menus
Set Channels Automatically
“Accessing the Setup Menu”
You will have to perform the following 3 steps for all other 
operations on page 5566.
  With the unit stopped 
  ,  to select “Other Functions”, 
then 
OK
  ,  to select “Setup”, then 
OK
 Tips
To return to the previous screen
  Press [RETURN]. Even if you have changed an option, the change 
is not activated until you press [OK].
To exit the screen
Press [RETURN] several times.
 Notes
Changed settings remain intact even when switching the unit to 
standby.
Perform steps 13 of “Accessing the Setup Menu” (
						

							56
RQT9056
Modifying the caption
  
,  to select the “Caption” 
column, then 
OK
After selecting a channel (
						

							57
RQT9056
  , then OK
11  Enter a 4-digit password with the 
numbered buttons, then 
OK
–  A screen appears con rming that you have set a 
password. Press [OK].
If you select “Off ” for “Set”:
A screen appears con rming that you haven’t set a 
rating. Press [OK].
To change the password
  Enter a 4-digit password with the 
numbered buttons, then 
OK
  
,  to select “Change 
Password”, then 
OK
  Enter the new password with the 
numbered buttons, then 
OK
–  A screen appears confirming that you have set a 
password. Press [OK].
 Tips
To clear the password
(
						

							58
RQT9056
 Tips
To cancel in the middle
Press [RETURN].
 Notes
  
This may take some time, up to a few hours in some cases.
  If the following message appears
Setup
Setup
AudioDisplayTV ScreenVHS
Channel
Disc
VideoNoYe s
OK
Set Clock Automatically
12/14/2008           5:28 AMDST-----------        Off
Time Zone----        EST
Setting completed as follows.
Finish the setup with this clock time?
Note:Selecting“No”will start channel scanning 
again and renew the clock time.
If the time is correct, press [] to select “Yes”, then press [OK].
–  If you select “No”, auto setting starts again, then the above 
screen reappears. Repeat this step until the correct time 
appears.
  If the clock is not correct, set the clock with “Adjust Time Zone” 
(
						

							59
RQT9056
Restore Default Settings
Perform steps 13 of “Accessing the Setup Menu” (
						

							60
RQT9056
Still Mode (paused video)
Perform steps 13 of “Accessing the Setup Menu” (