Panasonic Dmr Es45 Operating Instructions Manual

							21
RQTV0141
To turn the TV on/off, change the TV input mode, select the TV 
channel and change the TV volume by means of this remote control, 
set the remote control as follows.
Point the remote control at the TV
While pressing [Í, POWER TV], enter the code 
using the numeric buttons.
e.g., 0250: press [0] > [2] > [5] > [0].
Manufacturer and Code No. 
≥Test by turning on the TV and changing channels. Repeat the 
procedure until you find the code that allows correct operation.
≥If your TV brand is not listed or if the code listed for your TV does 
not allow control of your TV, this remote control is not compatible 
with your TV.Change the remote control code on the main unit and on the remote 
control (the two must match) if you place other Panasonic products 
close together. When changing the remote control code, make sure 
the two codes are same.
Use “1”, the factory set code, under normal circumstances.[1]While stopped
Press [FUNCTIONS].
[2]Select “Other 
Functions” with [
3, 4] 
and press [ENTER].
[3]Select “Setup” with [
3, 
4] and press [ENTER].
[4]Select “Setup” with [
3, 
4] and press [2,1].
[5]Select “Remote Control Code” with [
3, 4] and 
press [ENTER].
[6]Use [
3, 4] to select the code (1, 2 or 3) and 
press [ENTER].
≥The code on the unit has been set.
[7]While pressing [ENTER], press and hold for 
about 2 seconds the numeric button ([1], [2] or 
[3]) corresponding to the code you selected in 
step 6. 
≥The code on the remote control has been set.
[8]Press [ENTER]. 
∫When the following indicator appears on the unit’s 
display
The unit’s remote control code
Change the code on the remote control to match the main unit’s 
code (lstep 7).
∫To return to the previous screen
Press [RETURN].
∫To exit the screen
Press [RETURN].
Television operation
Panasonic
National
QUASAR0051, 0250 PHILIPS (RC-5) 0054
RCA 0047
SAMSUNG 0060, 0587, 
0702
FISHER 0154 SANYO 0154
GE 0047 SHARP 0093, 0165
GOLDSTAR 0178, 0317, 
0457SONY 0000
HITACHI 0145 SYLVANIA 0054
JVC 0053 THOMSON 0047
LG 0178, 0317, 
0457TOSHIBA 0156
MAGNAVOX 0054 ZENITH 0017
MITSUBISHI 0150
When other Panasonic products 
respond to this remote control
No DiscFUNCTIONS No Disc
Program
CopyOther Functions
Setup
ENTER
RETURN
Other settings
M6VP&PC.book  21 ページ  ２００６年２月６日　月曜日　午後３時２９分 
						

							22
RQTV0141
Other settings
“Clock Settings” made here are applied to VHS as well.
[1]While stopped
Press [FUNCTIONS].
[2]Select “Other Functions” with [
3, 4] and press 
[ENTER].
[3]Select “Setup” with [
3, 4] and press [ENTER].
[4]Select “Setup” with [
3, 4] and press [2, 1].
[5]Select “Clock Settings” with [
3, 4] and press 
[ENTER].
[6]Select “Set Clock Automatically” with [
3, 4] 
and press [ENTER].
[7]Press [ENTER].
≥Auto setting starts. This can take some time, up to a few hours 
in some cases. The following screen appears when setting is 
complete. 
≥If the time was not set correctly, use manual clock setting or 
time zone adjust.
≥DST, (Daylight Saving Time) shows the summertime setting.≥Time Zone shows the time difference from Greenwich Mean 
Time (GMT).
EST  (Eastern Standard Time)
l GMT j5
CST  (Central Standard Time)
l GMT j6
MST  (Mountain Standard Time)l GMT j7
PST  (Pacific Standard Time)l GMT j8
AST (Alaska Standard Time)
l GMT j9
HST  (Hawaii Standard Time)l GMT j10
For other areas: xx hr 
[8]Press [ENTER].
∫To cancel in the middle
Press [RETURN]. 
≥Follow steps 1 to 5 of “Clock Settings”.
Adjust the time zone (
j1 or i1) if it was not set correctly with auto 
clock setting.
You can set this menu only after “Set Clock Automatically” is 
completed.
[6]Select “Adjust Time 
Zone” with [
3, 4] and 
press [ENTER].
[7]Select “j1” or “i1” 
with [
3, 4] and press [ENTER].
∫To return to the previous screen
Press [RETURN]. 
Clock Settings
∫ Set Clock Automatically
DVD/VHS 
CHAPTERCREATE 
TV/VIDEO
RETURN
AB
SCHEDULE
DELETE ADD/DLTCH
ENTER
FUNCTIONS
VOLUMECH
CH
POWER POWER
PL AYPA U S E STOPSKIP/INDEX
SLOW/SEARCH
REW
FF
3
2
1
6
5 4
9
8
7
0
INPUT
SELECT
VCR/TV
F Rec
REC MODE
SUB MENU
CM SKIPTIME SLIP/     JET REW
DIRECTNAVIGATOR
DISPLAY AUDIO
RECSTATUS
TRACKING/V-LOCKTRACKING/V-LOCK
RESETRESET
CANCEL
DRIVE
 SELECT
VCR/TV
RETURN
FUNCTIONS3, 4, 2, 1
ENTERCH, W, X
No DiscFUNCTIONS No Disc
Program
CopyOther Functions
ENTER
RETURN
Off Timer
ChannelSetupDiscVideoAudioDisplayTV Screen
Remote Control CodeClock Settings
6 HoursSet Code 1
Quick StartRestore Default SettingsOn
Setup
VHS
Set Clock Automatically
Auto Clock Setting is complete.
4/4/2007 11:15 AMDST------------------ OnTime Zone---------   CST
∫ Adjust Time Zone
Adjust Time  Zone
0j1
i1
M6VP&PC.book  22 ページ  ２００６年２月６日　月曜日　午後３時２９分 
						

							23
RQTV0141
Connection (without Audio/Video cable) only
In some cases, interference (lines or patterning) or a very poor 
picture may appear on the TV when the DVD Recorder is 
connected. If this happens, follow the steps below to change 
the video playback channel (RF output channel) to remove the 
interference.
[1]Press [FUNCTIONS] for 
more than 5 seconds.
The RF output channel number is 
displayed on the unit display.
[2]Press [CH,W, X] to 
select a channel number 
(CH3 or CH4).
The unit’s display
Each time you press the button:
CH 3 (Default setting) (# CH4 (# OFF
                  ^-----------------------------------------------J
≥Set the RF output channel of the DVD Video Recorder to 
“OFF” (RF OFF) when the DVD Video Recorder is connected 
to the TV via the Audio/Video cable. 
[3]Press [ENTER] to finish this setting.
Removing Interference
∫When you set the RF output channel to “CH3” or 
“CH4”
A picture is output on CH3 or CH4 from RF output.
Press [VCR/TV] to switch the mode from TV to VCR, and vice 
versa.
≥When the TV mode is selected, the “TV” indicator lights on the 
unit’s display and you can watch TV.
≥When the “TV” indicator does not light on, then VCR mode is 
selected and you can watch images from the unit.
TV screen
Picture with interference
RF Output Channel
Press the channel up/down buttons
to select a RF Output Channel.
C h .       3
ENTER
The unit’s display
The clear picture
Other settings
M6VP&PC.book  23 ページ  ２００６年２月６日　月曜日　午後３時２９分 
						

							24
RQTV0141
Recording television programs
[1]Press [
						

							25
RQTV0141
[RAM] [-R] [-R]DL] [-RW‹V›] [+R] [+R]DL] [+RW] [VHS]
[RAM] [-R] [-R]DL] [-RW‹V›]
≥You can record up to 99 titles on a disc.
[+R] [+R]DL] [+RW]
≥You can record up to 49 titles on a disc.
≥It is not possible to record digital broadcasts that allow “One time 
only recording” onto DVD-R, DVD-R DL, DVD-RW, +R, +R DL, 
+RW or 8 cm (3q) DVD-RAM discs. Use a CPRM compatible DVD-
RAM.
≥Recording will take place on open space on the disc. Data will not 
be overwritten.
≥If there is no space left on the recording disc, you will need to 
erase unwanted titles (l41, 59) or use a new disc.
Preparation
≥Release protection (disc l60, cartridge l60). [RAM]
≥Select the unit viewing channel (e.g. AV input) on the TV.
≥Select an audio type you want to record. (l27)
[1]Press [Í, DVD/VHS POWER] to turn the unit on.
[2]Press [DRIVE SELECT] to select the drive you 
want to record on (DVD or VHS). 
[3]Insert a disc. 
(l24)
≥When using a DVD-RAM for the first time with the unit, format 
it to ensure accurate recording (l61, “Deleting all contents of 
a disc or card –Format”).
or
Insert a video cassette with an intact accidental 
erasure prevention tab. 
(l24)
[4]Press [CH, W, X] to select the channel.
≥To select with the numeric buttons:
Antenna Mode (Airwaves)
e.g., “5”: [0] )[5]
“15”: [1] )[5]
CableTV Mode (Cable)
e.g., “5”: [0] )[0] )[5]
“15”: [0] )[1] )[5]
“115”: [1] )[1] )[5]
[5]Press [REC MODE] to select the recording 
mode. 
[DVD]
XP, SP, LP or EP
[VHS]
SP, EP or VP
[6]Press [¥, REC] to start recording. 
≥You cannot change the channel or recording mode during 
recording. You can change them while recording is paused, 
but the material is recorded as a separate title.
∫To pause recording
Press [;, PAUSE]. (Press again to restart recording.)
≥Title is not split into separate titles. [DVD]
≥You can also press [¥, REC] to restart recording.
∫To stop recording
Press [∫, STOP].
≥Recorded as 1 title until the position where stopped. [DVD]
≥[-R] [-R]DL] [-RW‹V›] [+R] [+R]DL] [+RW]
It takes about 30 seconds for the unit to complete recording 
management information after recording finishes. 
∫To show the remaining time
[DVD]
Press [STATUS] several times. (l40)
[VHS]
[1]Select “Select Tape Length” from the Setup and select the
corresponding tape length. (l65)
[2]Press [STATUS] several times.
The remaining tape time may not be displayed correctly depending
on the tape used. 
Notes
≥Even if the video cassette you use is labeled “S-VHS”, it is not
possible to record in the S-VHS system with the unit. It 
records in the normal VHS system. [VHS]
≥When recording is paused for 5 or more minutes, the unit returns
to stop mode. [VHS] 
≥The remaining tape time is only displayed during playback or 
recording. [VHS]
Recording procedures
When recording to DVD-R, DVD-R DL, DVD-RW (DVD-Video 
format), +R, +R DL or +RW
≥When recording MTS broadcasts
-If you do not connect a cable box
Select “Main” or “SAP” in “Multi-channel TV sound (MTS)” in 
the Setup menu (l64).
-If you connect a cable box
Select “Main” or “SAP” on the cable box.
≥The aspect ratio of the recorded image will be 4:3.
≥To play a DVD-R, DVD-R DL, DVD-RW (DVD-Video format), 
+R or +R DL recorded using this unit on another playback 
source, the disc must first be finalized (l61).
≥[+RW] To enable play on other DVD equipment, please use 
“Create DVD Top Menu” in DVD Management menu (l62). 
Remaining time on the disc
Recording television programs
M6VP&PC.book  25 ページ  ２００６年２月６日　月曜日　午後３時２９分 
						

							26
RQTV0141
Recording television programs
Depending on the content being recorded, the recording times may 
become shorter than indicated.
This unit uses variable bit rate (VBR) recording which varies the 
amount of data recorded to suit the images, so actual recording 
times and remaining recording times shown by the unit will be 
different. (The difference will be especially noticeable with DVD-
R DL and +R DL.)
Use a disc with plenty of remaining time to be sure.
°
1It is not possible to record or play continuously from one side of 
a double sided disc to the other.
°
2When “Recording Time in EP Mode” has been set to “EP (6H)” 
in the Setup menu. (l64)
The sound quality is better when using  “EP (6H)” than when 
using “EP (8H)”.
°
3It is not possible to record continuously from first layer to second 
layer.
 
Note
When recording to DVD-RAM using EP (8H) mode, play may not be 
possible on DVD players that are compatible with DVD-RAM. In this 
case use EP (6H) mode.
FR (Flexible Recording mode l29):
≥You can set FR mode when transferring (copying) or programming 
scheduled recordings.
Note
You cannot play VP recording on other equipment.
∫ Recording modes and approximate 
recording times (DVD)
DVD-RAMDVD-R
DVD-RW
+R, +RW
(4.7 GB)
Single-sided
(4.7 GB)Double-sided°1
(9.4 GB)
XP 
(High quality)1 hour 2 hours 1 hour
SP (Normal) 2 hours 4 hours 2 hours
LP 
(Long recording)4 hours 8 hours 4 hours
EP (Extra long 
recording)8 hours 
(6 hours°
2)16 hours 
(12 hours°2)8 hours 
(6 hours°2)
FR (Flexible 
Recording)8 hours 
maximum8 hours 
maximum 
for one side8 hours 
maximum
DVD-R DL, +R DL°3 (8.5 GB)
First layerSecond layer
XP 
(High quality)55 minutes 50 minutes
SP (Normal) 1 hour 50 minutes 1 hour 40 minutes
LP 
(Long recording)3 hours 40 minutes 3 hours 20 minutes
EP (Extra long 
recording)7 hours 25 minutes
(5 hours 30 minutes°2)6 hours 50 minutes(5 hours 15 minutes°2)
FR (Flexible 
Recording)7 hours 25 minutes 
maximum6 hours 50 minutes 
maximum
DVD/VHS 
CHAPTERCREATE 
TV/VIDEO
RETURN
AB
SCHEDULE
DELETE ADD/DLTCH
ENTER
FUNCTIONS
VOLUMECH
CH
POWER POWER
PL AYPA U S E STOPSKIP/INDEX
SLOW/SEARCH
REW
FF
3
2
1
6
5 4
9
8
7
0
INPUT
SELECT
VCR/TV
F RecREC MODE
SUB MENU
CM SKIPTIME SLIP/     JET REW
DIRECTNAVIGATOR
DISPLAY AUDIO
RECSTATUS
TRACKING/V-LOCKTRACKING/V-LOCK
RESETRESET
CANCEL
DRIVE
 SELECT
DRIVE SELECT
AUDIO
∫
µ
2, 1
ENTER
∫ Recording modes (VHS)
Recording mode
SP: You can record the length shown on the tape.
EP: 3 times the length of SP mode.
VP: 5 times the length of SP mode.
≥To have a longer recording capacity, select “EP” or “VP”.
≥If the image quality is important to you or if you wish to store the 
tape for a long period, select “SP”.
≥The unit can play tapes recorded in LP mode on other equipment 
(“LP” lights on the unit’s display).
VP mode:
≥A tape recorded in VP mode by the unit cannot be played 
back by other VCRs. It is recommended to distinguish it from 
other tapes by writing “VP” on the tape label, etc.
≥It takes more time for automatic tracking to work when playing 
tapes recorded with VP mode, and it may not work at all with 
some tapes. Do tracking manually if this is the case (l38).
EP (6H)°2
EP (8H)
LP
SP
XP
Picture quality
Recording time
M6VP&PC.book  26 ページ  ２００６年２月６日　月曜日　午後３時２９分 
						

							27
RQTV0141
The unit automatically switches to standby when it has not been 
used for about 6 hours. 
You can turn this feature off or change the time to 2 hours. 
(l63, “Off Timer”)
[RAM] [-RW‹V›] [+R] [+R]DL] [+RW]
When you insert a new disc and a disc recorded on a computer or 
other equipment, a format confirmation screen might be displayed. 
Format the disc to use it. However all the recorded contents are 
deleted.
Press [2, 1] to select “Yes” and press [ENTER].
≥Several steps are necessary to format a disc. Refer to “Deleting all 
contents of a disc or card –Format”. (l61)
[-R] [-R]DL] [-RW‹V›] [+R] [+R]DL]
When you press [
						

							28
RQTV0141
Recording television programs
You can play discs while VHS recording. The recording will not be 
affected.
≥DVD playback (l32)
For your reference
≥You cannot record on discs while VHS recording.
You can play tapes while DVD recording. The recording will not be 
affected.
≥VHS playback (l37)
For your reference
≥You cannot record on tapes while DVD recording.
Preparation
≥Connection (without Audio/Video cable)
-Make sure that the TV indicator is lit on the unit’s display. If it is 
not lit, press [VCR/TV] to light it.
≥Connection (with Audio/Video cable)
-Press [TV/VIDEO] to change the input mode to “TV”.
Press TV’s [CH, W, X] to select the desired TV 
channel.
For your reference
≥You can also do this if the unit is making a scheduled recording.
≥The recording is unaffected.[RAM]
Preparation
≥Select DVD side with pressing [DRIVE SELECT].
Hint
≥Sound is not output while fast-forwarding.
You can start play from the beginning of the title while continuing to 
record it.
While recording or scheduled recording
Press [1, PLAY].
≥Play starts while recording proceeds.
For your reference
≥Play cannot be started until at least 2 seconds after recording 
starts.
You can play a title previously recorded while you are recording 
another title.
[1]While recording or scheduled recording
Press [DIRECT NAVIGATOR]. (l32)
[2]Use [3, 4, 2, 1] to select a title and press 
[ENTER].
≥ Play starts while recording proceeds.
∫To exit the Direct Navigator screen
Press [DIRECT NAVIGATOR].
For your reference
≥During simultaneous recording and play, you cannot edit or erase 
titles with the Direct Navigator or playlists.
≥Even if you start play while the unit is on standby for scheduled 
recording, recording starts when the time you set is reached.
Playing DVD while recording VHS
Playing VHS while recording DVD
Watching the TV while recording
DVD/VHS 
CHAPTERCREATE 
TV/VIDEO
RETURN
AB
SCHEDULE 
DELETE ADD/DLTCH
ENTER
FUNCTIONS 
VOLUMECH
CH
POWER POWER
PLAYPA U S E STOPSKIP/INDEX
SLOW/SEARCH
REW
FF
3
2
1
6
5 4
9
8
7
0
INPUT
SELECT
VCR/TV
F Rec
REC MODE
SUB MENU
CM SKIPTIME SLIP/     JET REW
DIRECT NAVIGATOR 
DISPLAY AUDIO
RECSTATUS
TRTRACKING/CKING/V-LOC-LOCK
RESETRESET
CANCEL
DRIVE
 SELECT
DRIVE
SELECT
DIRECT
NAVIGATOR
∫
RETURN
F Rec
1
STATUS
3, 4, 2, 1
ENTER
VCR/TV TV/VIDEO CH, W, X
Playing while you are recording
∫ Playing from the beginning of the title you 
are recording–Chasing playback
∫ Playing a title previously recorded while 
recording–Simultaneous rec and play
- -
DIRECT NAVIGATOR Title ViewDVD-RAM09
- -- -- -
0807
10  10/23 MON   8   10/23 MON 8   10/24 TUE
07Picture Video
¥: Currently recording
M6VP&PC.book  28 ページ  ２００６年２月６日　月曜日　午後３時２９分 
						

							29
RQTV0141
[RAM] [-R] [-R]DL] [-RW‹V›] [+R] [+R]DL] [+RW]
The unit calculates a recording rate that enables the recording to fit 
in the time you set (within the remaining time on the disc) with the 
best picture quality.
 
Preparation
≥Select DVD side with pressing [DRIVE SELECT].
≥Select the channel to record. 
[1]While stopped
Press [F Rec].
[2]Press 
[2,1] to select “Hour” and “Min.” and 
press 
[3,4] to set the recording time.
≥You can also set the recording time with the numbered 
buttons.
≥You cannot record for more than 8 hours.
[3]When you want to start recording
Press [3,4,2,1] to select “Start” and press 
[ENTER].
≥Recording starts.
To exit the screen without recording
Press [RETURN].
To stop recording partway
Press [
∫, STOP].
To show the remaining time
Press [STATUS] several times. (l40)
For your reference
≥During a Flexible Recording, all recording mode indicators light up 
on the unit’s display.
≥It is not possible to change the channel or recording mode while 
Flexible Recording is paused.
Flexible Recording
(Recording that fits the remaining disc space)
Using “FLEXIBLE RECORDING” is convenient in these 
kind of situations.
≥When the amount of free space on the disc makes selecting 
an appropriate recording more difficult
≥When you want to record a long program with the best 
picture quality possible
e.g., Recording a 90 minute program to disc
If you select XP mode, the program will not fit one disc.
4.7 GB
DVD-RAM
4.7 GB
DVD-RAM4.7 GB
DVD-RAM
4.7 GB
DVD-RAM
If you select SP mode, the program will fit one disc.
If you select “FLEXIBLE RECORDING” the 
program will fit one disc perfectly.A second disc is necessary for 
30 minutes of the program.
However there will be 30 minutes 
remaining disc space
Flexible Recording
StartCancel
Record in FR mode.
Set recording time1 Hour 23 Min. Max recording time
1 Hour 23 Min.Maximum recording time
This is the maximum 
recording time in FR mode.
Recording television programs
M6VP&PC.book  29 ページ  ２００６年２月６日　月曜日　午後３時２９分 
						

							30
RQTV0141
Scheduled Recording
∫Scheduled recording automatically starts at the set 
time.
≥Scheduled recording can be started whether the unit is turned on 
or off. When the unit is turned off, the sound and the video cannot 
be outputted to the TV.
∫Scheduled recording for TV programs cannot be 
executed on both DVD and VHS at the same time.
Make sure the scheduled recording start times do not overlap on 
both DVD and VHS Scheduled Recording List screens.
When the scheduled recording settings overlap:
≥When the start time of both scheduled recordings is the same, the 
programme that you register later has priority. 
≥If there is a VHS scheduled recording that overlaps a DVD 
scheduled recording that is currently being recorded, it may not be 
possible to operate the VHS during the overlap.
[RAM] [-R] [-R]DL] [-RW‹V›] [+R] [+R]DL] [+RW] [VHS]
You can enter up to 16 programs a month in advance.
Preparation
≥Release protection (disc l60, cartridge l60) [RAM].
≥Insert a disc (l24) and confirm there is sufficient empty space for 
recording on it (l40).
≥Check that the clock is set to the correct time.
≥When connecting a cable box or satellite receiver, select the 
channel on the cable box or satellite receiver before scheduled 
recording starts. 
[1]Press [SCHEDULE].
≥Make sure “New Scheduled Recording” is selected.
[2]Press [ENTER], to move and change the items 
using [
3, 4, 2, 1].
≥You may use the numeric buttons to enter “Channel”, “Date”, 
“On”, and “Off”.
≥Channel (Program Position/TV Station Name)
≥Date
You can also make a daily or weekly program.
Each daily or weekly program is counted as one program.
≥On (start time)/Off (finish time)
The time increases or decreases in 30-minute intervals if you 
hold down the button.
≥Drive
You can select DVD or VHS drive. 
You can also press [DRIVE SELECT] to select the drive.
DV D,.VHS
≥Mode (Recording mode)
You can also press [REC MODE] to change the recording 
mode.
[DVD] XP,.SP,.LP,.EP,.FR,.XP... (l26)
[VHS] SP,.EP,.VP,.AUTO
°,.SP... (l26)
°Auto SP/EP mode (l31)
≥Title Name
Press [2, 1] to select “Title Name” and press [ENTER] 
(l58).
[3]Press [ENTER] when you have finished making 
changes.
≥“ ” lights on the unit’s display. (l13)
≥“Invalid Entry” is displayed when you enter the wrong item. 
Reenter the item.
≥Make sure that the scheduled recording has been 
programmed correctly on the SCHEDULE LIST screen (l31).
≥To continue programming:
Select “New Scheduled Recording” and repeat steps 2 to 3.
[4]Press [RETURN].
Notes
≥When the unit is carrying out a scheduled recording, you may 
utilize playback.
≥When the disc or video cassette is removed, scheduled recording 
standby is cancelled (the “ ” indicator goes out). You can put the 
unit back on standby by inserting a recordable disc or video 
cassette (the “ ” indicator comes on again).
≥When a video cassette is not inserted or a video cassette with no 
accidental erasure prevention tab is inserted, the warning 
message appears before the recording starts because scheduled 
recording cannot be executed.
≥When recording more than one program in a row, for DVD-RAM 
the first few seconds, and for DVD-R, DVD-R DL, DVD-RW, +R, 
+R DL or +RW about the first 30 seconds of all programs from the 
second one onwards will not be recorded.
≥Even if you set the Title Name on the scheduled recording screen, 
it is not recorded on video cassette.
≥If you set “DST” (Daylight Saving Time) to “ON” when manually 
setting the clock (l19), scheduled recording may not work when 
summer switches to winter and vice versa.
Cautions for using scheduled recording 
on DVD and VHS
Programming scheduled recordings
DVD/VHS 
CHAPTERCREATE 
TV/VIDEO
RETURN
AB
SCHEDULE
DELETE ADD/DLTCH
ENTER
FUNCTIONS
VOLUMECH
CH
POWER POWER
PL AYPA U S E STOPSKIP/INDEX
SLOW/SEARCH
REW
FF
3
2
1
6
5 4
9
8
7
0
INPUT
SELECT
VCR/TV
F Rec
REC MODE
SUB MENU
CM SKIPTIME SLIP/     JET REW
DIRECTNAVIGATOR
DISPLAY AUDIO
RECSTATUS
TRACKING/V-LOCKTRACKING/V-LOCK
RESETRESET
CANCEL
DRIVE
 SELECT
REC MODE
DRIVE
SELECT
∫
RETURN
SCHEDULE
3, 4, 2, 1
ENTERCH,  
ADD/DLT
Numeric
buttons
Channel No Date
On CheckOff Drive
Mode
Schedule
ListDVD
VHS
5/ 5 Fri   6:11 PM Remain 1:00 XP:
New Scheduled Recording 01 5/ 6 Sat 6:10 PM 6:30 PM DVD XP OK4New Scheduled 
Recording is 
selected.
SCHEDULED
RECORDING
ModeOff OnChannelDate
Title Name
P ENTER t t
::
DVD
VHS
5/ 5 Fri   6:11 PM Remain 1:00 XP:
Drive
M6VP&PC.book  30 ページ  ２００６年２月６日　月曜日　午後３時２９分