Panasonic Dmr Es35 Operating Instructions Manual

							11
RQTV0134
Control reference guide
(1)Turn the unit on  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .l16
(2)Select drive (DVD or VHS) . . . . . . . . . . . . . . . . . . . . l above
(3)Select channels and title numbers etc./Enter numbers
(4)Cancel/Reset the tape counter
(5)Basic operations for recording and play
(6)Skip the specified time/ . . . . . . . . . . . . . . . . . . . . . . . . . .l31 
Jet rewind button (JET REW)  . . . . . . . . . . . . . . . . . . . . .l34
(7)Direct Navigator . . . . . . . . . . . . . . . . . . . . . . . . . . . . .l30, 32
(8)Selection/Enter, Frame-by-frame  . . . . . . . . . . . . . . .l16, 31
(9)Show sub menu . . . . . . . . . . . . . . . . . . . . . . . . . .l33, 38, 42
(10)Select audio  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .l25, 31
View select (A)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .l48
(11)Show on-screen menu . . . . . . . . . . . . . . . . . . . . . . . . . . .l36
View select (B)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .l48
(12)Start recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .l23
(13)Change recording mode  . . . . . . . . . . . . . . . . . . . . . .l23, 28
(14)Transmission window
(15)TV operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .l19, 26
(16)Channel select/
TRACKING/V-LOCK  . . . . . . . . . . . . . . . . . . . . . . . . . . . . .l35
(17)Add/delete channel  . . . . . . . . . . . . . . . . . . . . . . . . . . . . .l17
(18)Input select (IN1, IN2, DV)  . . . . . . . . . . . . . . . . . . . . . . . .l50
(19)Delete items  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .l52
(20)Skip a minute forward  . . . . . . . . . . . . . . . . . . . . . . . . . . .l31
(21)Show scheduled recording list . . . . . . . . . . . . . . . . . . . .l28
(22)Show FUNCTIONS window . . . . . . . . . . . . . . . . . . . . . . .l37
(23)Return to previous screen
(24)Select VCR/TV  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .l21
(25)Create chapters  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .l31
(26)Start Flexible Recording  . . . . . . . . . . . . . . . . . . . . . . . . .l27
(27)Show status messages . . . . . . . . . . . . . . . . . . . . . . .l35, 37
Notes
≥Buttons such as the [¥, REC] button do not protrude as much as 
other buttons to stop them from being pressed accidentally.
≥The word “button” is not used in these operating instructions so 
“Press the [ENTER] button.” is shown as “Press [ENTER].”
≥You can use this remote control to operate your TV if you set the 
TV manufacturer code (l19).
Remote control
DVD/VHS 
CHAPTERCREATE 
TV/VIDEO
RETURN
AB
SCHEDULE
DELETE ADD/DLT
CH
ENTER
FUNCTIONS
VOLUMECH
CH
POWER POWER
PL AYPAUSE STOP
SKIP/INDEX
SLOW/SEARCH
REW
FF
3
2
1
6
5 4
9
8
7
0
INPUT
SELECT
VCR/TV
F Rec
REC MODE
SUB MENU
CM SKIPTIME SLIP/     JET REW
DIRECTNAVIGATOR
DISPLAY AUDIO
RECSTATUS
TRACKING/V-LOCKTRACKING/V-LOCK
RESETRESET
CANCEL
DRIVE
 SELECT
(1)
(2)
(4)
(5)
(7)
(6) (3)
(9)
(15)
(16)
(18)
(19)
(20)
(21)
(22)
(8)
(25)
(26)
(14)
(23)
(17)
(24)
(27)(10)
(11)
(12)
(13)
∫[DRIVE SELECT] button
≥Before performing DVD operations, be sure to 
press the [DRIVE SELECT] button to select DVD 
side. Also, make sure the DVD indicator lights up 
on the unit.
≥Before performing VHS operations, be sure to 
press the [DRIVE SELECT] button to select VHS 
side. Also, make sure the VHS indicator lights up on 
the unit.DRIVE
SELECT







DRIVE
SELECT







Video cassette information/Useful features/Control reference guide
M6VP&PC.book  11 ページ  ２００６年２月６日　月曜日　午後３時２０分 
						

							12
RQTV0134
Control reference guide
(1)Cassette eject button (
						

							13
RQTV0134
STEP 1 Connection
This section includes diagrams of two common methods of connection (A-B, pages 13-14). Please connect using the one that best 
suits you.
≥Visit Panasonic’s homepage for more information about connection methods. (This is in English only.)
http://www.panasonic.com/consumer_electronics/dvd_recorder/dvd_connection.asp
≥Before doing any connection, turn off all the equipments and read the appropriate operating instructions.
≥Peripheral equipments and optional cables are sold separately unless otherwise indicated.
≥You need to subscribe to a cable TV or satellite service to enjoy viewing their programme.
≥Consult your service provider regarding appropriate cable box.
∫The unit’s RF OUT terminal
The picture and sound signal from this unit go through the RF OUT 
terminal to the television. 
Refer to page 14 if the antenna connector doesn’t match.
∫When the unit is not to be used for a long time
To save power, unplug it from the household AC outlet. This unit 
consumes a small amount of power, even  when it is turned off 
(approx. 8 W
).
TV TV
The unit
VCRVCR
The unit
∫Do not connect the unit through a video cassette 
recorder
Video signals sent through video cassette recorders will be 
affected by copyright protection systems and the picture will not be 
shown correctly on the TV.
A Connection with a television
R-AUDIO-L
VIDEO
R-AUDIO-L
VIDEO
S VIDEO
YPBPR
OPTICALCOMPONENT VIDEO  OUT
DIGITAL AUDIO OUT
 (PCM/BITSTREAM)DVD / VHS COMMON OUT
RF
OUT
VHF/UHF
RF
IN
R-AUDIO-L
VIDEOS VIDEOAC INDVD        PRIORITY OUT
VHF/UHF
RF IN AUDIO IN
VIDEO 
IN
RL
Red   White   
Red   White   Yellellow Red   White   Yellow
12
To  R F  I N
ToToDVD/VHS COMMON OUTDVD/VHS COMMON OUTTo
DVD/VHS COMMON OUT
Television
This unit’
s rear pane
lAudio/Video cable
(Included)
To RF OUT To household
AC outlet
(AC 120 V, 60 Hz)
AC power supply cord (Included)
Connect only after all other connections are complete.
75 hh
coaxial 
cable
(Included)75 
hh
coaxial 
cable Cable from wall or
antenna signal
3
4
Red   White   Red   White   Yellellow Red   White   Yellow
∫ Connection (with Audio/Video cable)
Connect in numerical order 1 to 4.
≥After this connection, set the RF output channel “OFF” 
(l16), and then press TV/VIDEO button of TV remote 
controller to select the AV input mode to the connected 
TV terminal. You can watch a video from this unit on 
your TV.
∫Connection (without Audio/Video cable)
You do not need to connect “3”.
The unit supplies a signal to the TV via the 75 ≠ coaxial 
cable on channel 3 or 4. It is possible to view the video 
picture on your TV in the same way that you watch TV 
broadcasts. 
≥After this connection, set the RF output channel “CH3” 
or “CH4” (l16).
Control reference guide/STEP 1 Connection
M6VP&PC.book  13 ページ  ２００６年２月６日　月曜日　午後３時２０分 
						

							14
RQTV0134
STEP 1 Connection
Use one of the following connections to suit the antenna lead to the unit’s RF IN terminal, and the 75 ≠ coaxial cable to the antenna terminals on 
the equipment (television etc.). Refer to other equipment’s operating instructions.
The unit has DVD/VHS COMMON output terminals and DVD PRIORITY output terminals.
v
DVD/VHS COMMON OUT
≥For DVD/VHS COMMON output terminals, both DVD and VHS 
signals can be output.
DVD PRIORITY OUT
≥You can also playback a tape with the DVD PRIORITY output 
terminal except while recording, or making a scheduled recording, 
on the DVD. (l15)
BConnection with a television and cable box or satellite receiver
R-AUDIO-L
VIDEO
R-AUDIO-L
VIDEO
S VIDEO
YPBPR
OPTICALCOMPONENT VIDEO  OUT
DIGITAL AUDIO OUT
 (PCM/BITSTREAM)DVD / VHS COMMON OUT
RF
OUT
VHF/UHF
RF
IN
R-AUDIO-L
VIDEOS VIDEOAC IN
AUDIO
VIDEO S VIDEO Satellite CableRLRFINOUT
VHF/UHF
RF IN AUDIO IN
VIDEO 
IN
RL
Red   White   
Red   White   Yellellow Red   White   Yellow
DVD        PRIORITY OUT
Red   White   Red   White   Yellellow
Cable box or 
Satellite receiver
Satellite antenna 
(Satellite receiver only)
1
5
Red   White   Yellow
2
3
To  R F  I N Television
(Included) To RF OUT Cable from wall or 
antenna signal
(AC 120 V, 60 Hz)
Connect only after all other 
connections are complete.
This unit’
s rear pane
l
Audio/Video cable
(Included)75 hh
coaxial 
cable
75 
hh
coaxial 
cable
6
Audio/Video cableTo  I N 1
AC power supply cord (Included)
To household
AC outlet
4
ToToDVD/VHS COMMON OUTDVD/VHS COMMON OUTTo
DVD/VHS COMMON OUT
7
75 hh
coaxial 
cable
Red   White   Red   White   Yellellow Red   White   Yellow Red   White   
Red   White   Yellellow Red   White   Yellow
If the antenna connector doesn’t match
Other antenna connections to the unitOther antenna connections to the television
∫A single twin lead∫A twin lead terminal
∫A twin lead and a coaxial cable∫A twin lead and coaxial plug terminal
∫Two twin leads∫Two twin lead terminals
DVD output and DVD/VHS output
300–75 ≠ transformer
from the antenna
(Flat) Twin lead 
300 ≠ cableTo this unit’s RF IN 
terminal
75 ≠ coaxial cable75–300 ≠ transformer
TelevisionVHF or UHF
from the antenna
(Flat) Twin lead 300 ≠ cable
To this unit’s RF IN 
terminal VHF/UHF band mixer
(Round)75 ≠ coaxial cableVHF/UHF band separator
Te l e v i s i o n 75 ≠ coaxial cableVHF
UHF
from the antenna
To this unit’s RF 
IN terminal
300–75 ≠ transformer (Flat) Twin lead
300 ≠ cableVHF/UHF band mixer
75 ≠ coaxial cableVHF/UHF band separator
TelevisionVHF
UHF
R-AUDIO-L
VIDEO
R-AUDIO-L
VIDEO
S VIDEO
YPBPR
OPTICALCOMPONENT VIDEO  OUT
DIGITAL AUDIO OUT
 (PCM/BITSTREAM)R-AUDDVD        PRIORITY OUT DVD /VHS COMMON OUT
DVD/VHS COMMON output
DVD PRIORITY output
M6VP&PC.book  14 ページ  ２００６年２月６日　月曜日　午後３時２０分 
						

							15
RQTV0134
S VIDEO OUT terminal
The S VIDEO OUT terminal achieves a more vivid picture than the 
VIDEO OUT terminal. (Actual results depend on the television.)
After completing “Connection with a television” (l13) or 
“Connection with a television and cable box or satellite receiver” 
(l14), connect S VIDEO cable as illustration below.
Usually you can watch a picture from INPUT2 terminal. When you 
want to playback VHS while recording on DVD, change to INPUT1 
terminal.COMPONENT VIDEO OUT terminal
These terminals can be used for either interlace or progressive 
output (l68) and provide a purer picture than the S VIDEO OUT 
terminal.
After completing “Connection with a television” (l13) or 
“Connection with a television and cable box or satellite receiver” 
(l14), connect COMPONENT VIDEO cable as illustration below.
Usually you can watch a picture from COMPONENT VIDEO INPUT 
terminal. When you want to playback VHS while recording on DVD, 
change to INPUT1 terminal.
≥Connect to terminals of the same color.
∫Connecting an amplifier with a digital input terminal
≥To enjoy multi-channel surround on DVD-Video, 
connect an amplifier with a built-in decoder 
displaying these logo marks using an optical digital 
audio cable and change the settings in “Digital Audio 
Output” (l57).
≥Before purchasing an optical digital audio cable (not 
included), check the terminal shape of the connected 
equipment.
≥You cannot use DTS Digital Surround decoders not suited to DVD.
≥Even if using this connection, output will be only 2 channels when 
playing DVD-Audio.
∫Connection to a stereo amplifier
To enjoy higher picture quality
∫ Connecting to the TV S VIDEO IN terminal
R-AUDIO-L
VIDEO
R-AUDIO-L
VIDEO
S VIDEO
YPBPR
OPTICALCOMPONENT VIDEO  OUT
DIGITAL AUDIO OUT
 (PCM/BITSTREAM)DVD / VHS COMMON OUT
DVD         PRIORITY OUTR-AUDIO-L
VIDEOS VIDEO
S Video  ca bleTelevision
Red   WhiteRed   White
AUDIO IN
VIDEO 
IN
S VIDEO 
IN RL
Audio cable
AUDIO IN
VIDEO 
IN
RL
Red   White   Yellow
This unit’s 
rear panelAudio/Video cable
INPUT1
INPUT2
(Included)
Red   WhiteRed   WhiteRed   White   
Red   White   Yellellow Red   White   Yellow
∫ Connecting to the TV COMPONENT VIDEO 
IN terminals
R-AUDIO-L
VIDEO
R-AUDIO-L
VIDEO
S VIDEO
YPBPR
OPTICALCOMPONENT VIDEO  OUT
DIGITAL AUDIO OUT
 (PCM/BITSTREAM)DVD / VHS COMMON OUT
DVD         PRIORITY OUTR-AUDIO-L
VIDEOS VIDEO
COMPONENT 
VIDEO INPUTAUDIO IN
RL
YPBPR
AUDIO IN
VIDEO 
IN
RL
Red   White   YellowRed   WhiteRed   WhiteINPUT1
Red   White   Red   White   Yellellow Red   White   Yellow
Component 
Video cable
Television
Audio cable
This unit’s  
rear panel
Audio/Videoudio/Video 
cacablele  Audio/Video 
cable (Included)(Included)   (Included) 
Red   WhiteRed   White
Connecting an amplifier or system component
R-AUDIO-L
VIDEO
R-AUDIO-L
VIDEO
S VIDEO
YPBPR
OPTICALCOMPONENT VIDEO  OUT
DIGITAL AUDIO OUT
 (PCM/BITSTREAM)DVD / VHS COMMON OUT
RF
OUT
VHF/UHF
RF
IN
DVD         PRIORITY OUTR-AUDIO-L
VIDEOS VIDEOAC IN
OPTICAL INAUDIO IN
RL
Red   WhiteRed   White
Optical digital audio cable
Do not bend sharply when 
connecting. Amplifier’s  
rear panel
Insert fully, with this side 
facing up.
Red   White
Red   WhiteRed   WhiteRed   White
This unit’s 
rear panelAudio cable
Amplifier’s  
rear panel
STEP 1 Connection
M6VP&PC.book  15 ページ  ２００６年２月６日　月曜日　午後３時２０分 
						

							16
RQTV0134
STEP 2 Plug-in Auto Tuning
After plugging the unit into your household AC outlet and pressing 
[Í, DVD/VHS POWER] to turn the unit on for the first time, the unit 
assists you to set the on-screen language, and automatically tunes 
in all the channels it can receive and sets the clock.
The unit automatically determines the type of transmission (airwaves 
or cable) and puts them into channels as follows.
Preparation
≥Turn on the TV and select the appropriate video input to suit the 
connections to the unit. (Example: AV input, CH3 or CH4)
≥If you connect the unit through a cable box or satellite receiver 
(l14), tune to your local PBS for Auto Clock Setting to work.
If there is no local PBS, set the clock manually (l17, “Set Clock 
Manually”).
[1]Press [Í, DVD/VHS POWER]. 
[2]Press [CH,W, X] to 
select an RF output 
channel number.
The unit’s display
Each time you press the button:
CH 3 (Default setting) (# CH4 (# OFF
                  ^-----------------------------------------------J
[3]Use [3, 4] to select the 
language and press 
[ENTER].
[4]Press [
3, 4] to select 
“4:3 TV” or “16:9 
Widescreen TV” and 
press [ENTER].
[5]Press [
3, 4] to select 
“On” or “Off” and press 
[ENTER].
If you activate “Quick Start” 
function, select “On”.
[6]Press [3, 4] to select 
“Internal TV Tuner” or 
“Input” and press 
[ENTER].
When you do not set channels 
on this unit, select “Input”. The 
unit then displays “Set Clock 
Manually” screen. 
Set the clock manually. (l17)
[7]Press [ENTER] to start Plug-in Auto Tuning. 
≥The unit then proceeds with Auto Clock Setting. The time is 
displayed when Auto Clock Setting is finished. 
≥DST, Daylight Saving Time, shows the summertime setting.
≥Time Zone shows the time difference from Greenwich Mean 
Time (GMT).
EST  (Eastern Standard Time)l GMT j5
CST  (Central Standard Time)l GMT j6
MST  (Mountain Standard Time)l GMT j7
PST  (Pacific Standard Time)l GMT j8
AST (Alaska Standard Time)l GMT j9
HST  (Hawaii Standard Time)l GMT j10
For other areas: xx hr
∫When one of the following screens appears
“No channels were found.” 
After turning off the unit, confirm 
following and perform setup 
again.
≥Confirm the antenna cable is 
firmly connected to RF IN 
terminal.
≥If you do not set channels on this unit, select “Input” in step 6.
“Auto Clock Setting is 
incomplete.”
Press [ENTER] and set clock 
manually. (l17)
[8]Press [ENTER].
BandChannel
Antenna Mode
(Airwaves)VHF 2 to 13
UHF 14 to 69
CableTV Mode
(Cable)VHF 2 to 13
CATV LOW BAND 95 to 99
CATV MID/SUPER BAND 14 to 36
CATV HYPER BAND 37 to 65
ULTRA BAND66 to 94
100 to 125
SPECIAL CATV CHANNEL 1
Regarding DST (Daylight Saving Time) (l17)
Legal revision is expected to change the DST period in 2007. 
When you use the unit with DST on, the change may cause the 
unit’s clock to go behind the actual time. Check the DST setting in 
Set Clock manually in the Setup menu, set DST off and reset the 
clock precisely if you are using this function.
Connection (without Audio/
Video cable):
Select “CH3” or “CH4” which 
displays the screen on the right.
Connection (with Audio/Video 
cable):
Select “OFF”.
DVD/VHS 
CHAPTERCREATE 
TV/VIDEO
RETURN
AB
SCHEDULE
DELETE ADD/DLTCH
ENTER
FUNCTIONS
VOLUMECH
CH
POWER POWER
PL AYPA U S E STOPSKIP/INDEX
SLOW/SEARCH
REW
FF
3
2
1
6
5 4
9
8
7
0
INPUT
SELECT
VCR/TV
F Rec
REC MODE
SUB MENU
CM SKIPTIME SLIP/     JET REW
DIRECTNAVIGATOR
DISPLAY AUDIO
RECSTATUS
TRACKING/V-LOCKTRACKING/V-LOCK
RESETRESET
CANCEL
DRIVE
 SELECT
µ
Í
CH, 
ADD/DLT
RETURN
FUNCTIONS3, 4, 2, 1
ENTERCH, W, X
Numeric
buttons
The unit’s display
Select Language
Seleccione el idioma
Sélection de langue
Press ENTER
Pulse ENTER
Appuyer sur ENTER
English
FrançaisEspañol
About “Quick Start” function
If you set Quick Start to on, you can start recording to DVD-
RAM about 1 second after you press [Í, DVD/VHS POWER] 
to turn the unit on and then sequentially press [¥, REC].
The following happens when you have selected “On”.
≥Power consumption in standby mode increases because 
power is supplied to the unit.
Select TV type  and press ENTER.
(Please refer to Operation Instruction  
for details.)
4:3 TV16:9 Widescreen TV
ENTER
Aspect Ratio Selection
The unit can be turned on faster, in about 
1 second. Please note that Quick Start
mode slightly increases power
consumption when the unit is off.
(See Operation instructions for details)
Turn Quick Start on ?
OnOff
ENTER
Quick start setting
Please select the source from which this
unit will record each time it is turned
on. Note: Selecting Internal TV Tuner
will start the Auto Channel Clock
Settings process.
This one time process takes a few minutes.
Internal TV TunerInput
ENTER
Default Recording Source
Set Channels Automatically
Ch.
Set Channels Automatically
Proceeding .  .  .
1   1   11
Set Clock Automatically
Auto Clock Setting is complete.
4/4/2007 12:15 AM
DST.............  On
Time Zone.... CST
No channels were found.
Please check antenna or cable connection,
then...
Press ENTER again.
Set Channels Automatically
Auto Clock setting is incomplete.
Press ENTER
to set clock manually.
Set Clock Automatically
M6VP&PC.book  16 ページ  ２００６年２月６日　月曜日　午後３時２０分 
						

							17
RQTV0134
∫If the clock is an hour slower or faster than the actual 
time
Select “j1” or “i1” in “Adjust Time Zone” in the Setup menu (l56).
Signal source, RF output channel, channel caption revert to the 
default values when you perform the procedure below. 
Scheduled recording settings are also cleared.
When the unit is on and stopped
[1]Press and hold [CH, W] and [CH, X] on the main 
unit for about 5 seconds.
The unit turns off.
[2]Press [Í, DVD/VHS POWER] to turn the unit on.
Plug-in Auto Tuning starts.
[1]While stopped
Press [FUNCTIONS].
[2]Select “Other Functions” with [
3, 4] and press 
[ENTER].
[3]Select “Setup” with [
3, 4] and press [ENTER]. 
[4]Select “Channel” with [
3, 4] and press [2,1].
[5]Select “Signal Source (RF IN)” with [
3, 4] and 
press [ENTER]. 
[6]Select “Antenna” or “Cable TV” with [
3, 4] and 
press [ENTER].
[7]Select “Set Channels Automatically” with [
3,4] 
and press [ENTER]. 
[8]Press [ENTER].
≥Auto Channel Setting starts. This takes a few minutes.
[9]Press [ENTER].
∫To cancel in the middle
Press [RETURN].
∫To exit the screen
Press [RETURN]. Add or delete channels if necessary channels are not set or 
unnecessary channels are set. 
[1]Press the numeric buttons to select a channel.
Antenna Mode (Airwaves)
e.g., “5”: [0] )[5]
“15”: [1] )[5]
CableTV Mode (Cable)
e.g., “5”: [0] )[0] )[5]
“15”: [0] )[1] )[5]
“115”: [1] )[1] )[5]
≥You can also use [CH, W, X] to select a channel.
[2]Press [CH, ADD/DLT].
e.g., The channel is deleted.
“Clock Settings” made here are applied to VHS as well.
[1]While stopped
Press [FUNCTIONS]. 
[2]Select “Other Functions” with [
3, 4] and press 
[ENTER].
[3]Select “Setup” with [
3, 4] and press [ENTER].
[4]Select “Setup” with [
3, 4] and press [2, 1].
[5]Select “Clock Settings” with [
3, 4] and press 
[ENTER].
[6]Select “Set Clock Manually” with [
3, 4] and 
press [ENTER].
[7]Use [
2, 1] to select the item you want to 
change, and press [
3, 4] to change the setting. 
≥DST (Daylight Saving Time): On or Off
If you select “On”, the clock is advanced one hour starting at 
2 a.m. on the first Sunday in April and ending at 2 a.m. on the 
last Sunday in October. 
≥Time Zone (l20)
[8]Press [ENTER]. 
≥The clock starts.
≥When you change the time zone, the recording times for titles 
recorded before the time zone adjustment also change to 
correspond to the new time zone. 
∫To return to the previous screen
Press [RETURN]. 
∫ Restart Plug-in Auto Tuning
(after relocation, for example)
∫ Restart Set Channels Automatically
No DiscFUNCTIONS No Disc
Program
CopyOther Functions
ENTER
RETURN
No DiscFUNCTIONS No Disc
Program
CopyOther Functions
Setup
ENTER
RETURN
Manual Channel Captions
Signal Source (RF IN)
ChannelSetupDiscVideoAudioDisplay
Set Channels AutomaticallyChannel CaptionsPreset Channel Captions
AntennaSetup
AntennaChannelSetupDiscCable TV Signal Source (RF IN)
Setup
∫ Adding and deleting channels
∫ Set Clock Manually
The unit’s display
Channel 15 Deleted
Off Timer
ChannelSetupDiscVideoAudioDisplayTV Screen
Remote Control CodeClock Settings
6 HoursSet Code 1
Quick StartRestore Default SettingsOn
Setup
VHS
Set Clock Manually
/:
/SAT PM Month Day Year
Hour Minute1
1
12 00 2000
DST Time ZoneOffEST
ENTER
STEP 2 Plug-in Auto Tuning
M6VP&PC.book  17 ページ  ２００６年２月６日　月曜日　午後３時２０分 
						

							18
RQTV0134
Other settings
You can use the preset captions, or manually enter new ones 
yourself.
The captions you enter are used as channel names and displayed 
on the Direct Navigator screen.
[1]While stopped 
Press [FUNCTIONS].
[2]Select “Other 
Functions” with [
3, 4] 
and press [ENTER].
[3]Select “Setup” with [
3, 
4] and press [ENTER]. 
[4]Select “Channel” with 
[
3, 4] and press [2,1].
≥Go to the item you want to set 
next.
≥Follow steps 1 to 4 of “Channel captions”.
[5]Select “Preset Channel 
Captions” with [
3, 4] 
and press [ENTER]. 
[6]Use [
3, 4] to select the 
caption and press [
1].
You can choose from the 
following captions.
ABC, PBS, CBS, CNN, FOX, 
ESPN, NBC, HBO, A&E, AMC, FAM, MAX, MTV, SHOW, TBS, 
USA, TNT, CBC, UPN, CTV, WB, TSN, DSC, GLOB
≥When selecting the caption, press and hold [3,4] to scroll up 
and down the screen quickly.
[7]Use [3,4] to select the channel corresponding 
to the caption and press [
2].
≥Channels are displayed only when they contain a station and if 
captions have not been added manually. 
≥To delete the channel number, press [¢, CANCEL].
≥Repeat steps 6 and 7 as necessary.
[8]Press [ENTER].
∫To return to the previous screen
Press [RETURN].
∫To exit the screen
Press [RETURN].≥Follow steps 1 to 4 of “Channel captions”.
[5]Select “Manual Channel Captions” with [3, 4] 
and press [ENTER].
[6]Use [
3, 4] to select the channel and press [1].
≥Channels are only displayed if they contain a station and if 
preset captions have not been added.
[7]Use [3, 4] to select the first character and 
press [
1].
≥You can choose from the following characters:
A to Z, 0 to 9, -, &, !, /, (space)
≥To delete the caption, press [¢, CANCEL].
≥Repeat this step to enter the other characters. 
[8]Use [2, 1] to return to the “Channel Number” 
column.
≥Repeat steps 6 to 8 to enter other channels. 
[9]Press [ENTER].
∫To return to the previous screen
Press [RETURN].
∫To exit the screen
Press [RETURN].
You do not have to change the setting when connected to a 4:3 
standard aspect TV that is not compatible with progressive output. 
(l68)
[1]While stopped
Press [FUNCTIONS].
[2]Select “Other Functions” with [
3, 4] and press 
[ENTER].
[3]Select “Setup” with [
3, 4] and press [ENTER].
[4]Select “TV Screen” with [
3, 4] and press [2,1].
[5]Select “TV Type” with [
3, 4] and press 
[ENTER]. 
≥Aspect 4:3/Aspect 16:9:
≥480p/480i:
Select “480p” if the TV is compatible with progressive output.
[6]Use [3, 4] to select the item and press 
[ENTER]. 
∫To return to the previous screen
Press [RETURN].
∫To exit the screen
Press [RETURN].
Channel captions
∫ Preset Channel Captions
CHAPTERCREATE 
RETURN
AB
SCHEDULE
ENTER
FUNCTIONS
VCR/TV
SUB MENU
TIME SLIP/     JET REW
DIRECTNAVIGATOR
DISPLAY AUDIO
TRACKING/V-LOCK
RESET
DVD/VHS 
TV/VIDEO
DELETE ADD/DLTCH
VOLUMECH
CH
POWER POWER
SKIP/INDEX
SLOW/SEARCH
REW
FF
3
2
1
6
5 4
9
8
7
0
INPUT
SELECT
TRACKING/V-LOCKTRACKING/V-LOCK
RESETRESET
CANCEL
DRIVE
 SELECTÍ
RETURN
FUNCTIONS3, 4, 2, 1
ENTER
Numeric
buttons
No DiscFUNCTIONS No Disc
Program
CopyOther Functions
Setup
ENTER
RETURN
Manual Channel Captions
Signal Source (RF IN)
ChannelSetupDiscVideoAudioDisplay
Set Channels AutomaticallyChannel CaptionsPreset Channel Captions
AntennaSetup
ChannelSetupDiscVideoAudioDisplayTV Screen
Preset Channel Captions
CaptionChannel Number
--
--
GLOB
ABC
----
PBS
CBS
Setup
ENTERVHS
∫ Manual Channel Captions
Selecting television type
ChannelSetupDiscVideoAudioDisplayTV Screen
Manual Channel Captions
Channel NumberCaption
AAAA
----
6----
8
10
--------
12
23
Setup
ENTERVHS
Aspect 4:3 & 480i4:3 TV
16:9 Aspect (Widescreen TV)
ChannelSetupDiscVideoAudioDisplayTV Screen
Aspect 4:3 & 480p
Aspect 16:9 & 480iAspect 16:9 & 480pTV Type
Setup
ENTERVHS
4:316:9
4:3 standard aspect TV 16:9 widescreen TV
M6VP&PC.book  18 ページ  ２００６年２月６日　月曜日　午後３時２０分 
						

							19
RQTV0134
To turn the TV on/off, change the TV input mode, select the TV 
channel and change the TV volume by means of this remote control, 
set the remote control as follows.
Point the remote control at the TV
While pressing [Í, POWER TV], enter the code 
using the numeric buttons.
e.g., 0250: press [0] > [2] > [5] > [0].
Manufacturer and Code No. 
≥Test by turning on the TV and changing channels. Repeat the 
procedure until you find the code that allows correct operation.
≥If your TV brand is not listed or if the code listed for your TV does 
not allow control of your TV, this remote control is not compatible 
with your TV.Change the remote control code on the main unit and on the remote 
control (the two must match) if you place other Panasonic products 
close together. When changing the remote control code, make sure 
the two codes are same.
Use “1”, the factory set code, under normal circumstances.[1]While stopped
Press [FUNCTIONS].
[2]Select “Other 
Functions” with [
3, 4] 
and press [ENTER].
[3]Select “Setup” with [
3, 
4] and press [ENTER].
[4]Select “Setup” with [
3, 
4] and press [2,1].
[5]Select “Remote Control Code” with [
3, 4] and 
press [ENTER].
[6]Use [
3, 4] to select the code (1, 2 or 3) and 
press [ENTER].
≥The code on the unit has been set.
[7]While pressing [ENTER], press and hold for 
about 2 seconds the numeric button ([1], [2] or 
[3]) corresponding to the code you selected in 
step 6. 
≥The code on the remote control has been set.
[8]Press [ENTER]. 
∫When the following indicator appears on the unit’s 
display
The unit’s remote control code
Change the code on the remote control to match the main unit’s 
code (lstep 7).
∫To return to the previous screen
Press [RETURN].
∫To exit the screen
Press [RETURN].
Television operation
Panasonic
National
QUASAR0051, 0250 PHILIPS (RC-5) 0054
RCA 0047
SAMSUNG 0060, 0587, 
0702
FISHER 0154 SANYO 0154
GE 0047 SHARP 0093, 0165
GOLDSTAR 0178, 0317, 
0457SONY 0000
HITACHI 0145 SYLVANIA 0054
JVC 0053 THOMSON 0047
LG 0178, 0317, 
0457TOSHIBA 0156
MAGNAVOX 0054 ZENITH 0017
MITSUBISHI 0150
When other Panasonic products 
respond to this remote control
No DiscFUNCTIONS No Disc
Program
CopyOther Functions
Setup
ENTER
RETURN
Other settings
M6VP&PC.book  19 ページ  ２００６年２月６日　月曜日　午後３時２０分 
						

							20
RQTV0134
Other settings
“Clock Settings” made here are applied to VHS as well.
[1]While stopped
Press [FUNCTIONS].
[2]Select “Other Functions” with [
3, 4] and press 
[ENTER].
[3]Select “Setup” with [
3, 4] and press [ENTER].
[4]Select “Setup” with [
3, 4] and press [2, 1].
[5]Select “Clock Settings” with [
3, 4] and press 
[ENTER].
[6]Select “Set Clock Automatically” with [
3, 4] 
and press [ENTER].
[7]Press [ENTER].
≥Auto setting starts. This can take some time, up to a few hours 
in some cases. The following screen appears when setting is 
complete. 
≥If the time was not set correctly, use manual clock setting or 
time zone adjust.
≥DST, (Daylight Saving Time) shows the summertime setting.≥Time Zone shows the time difference from Greenwich Mean 
Time (GMT).
EST  (Eastern Standard Time)
l GMT j5
CST  (Central Standard Time)
l GMT j6
MST  (Mountain Standard Time)l GMT j7
PST  (Pacific Standard Time)l GMT j8
AST (Alaska Standard Time)
l GMT j9
HST  (Hawaii Standard Time)l GMT j10
For other areas: xx hr 
[8]Press [ENTER].
∫To cancel in the middle
Press [RETURN]. 
≥Follow steps 1 to 5 of “Clock Settings”.
Adjust the time zone (
j1 or i1) if it was not set correctly with auto 
clock setting.
You can set this menu only after “Set Clock Automatically” is 
completed.
[6]Select “Adjust Time 
Zone” with [
3, 4] and 
press [ENTER].
[7]Select “j1” or “i1” 
with [
3, 4] and press [ENTER].
∫To return to the previous screen
Press [RETURN]. 
Clock Settings
∫ Set Clock Automatically
DVD/VHS 
CHAPTERCREATE 
TV/VIDEO
RETURN
AB
SCHEDULE
DELETE ADD/DLTCH
ENTER
FUNCTIONS
VOLUMECH
CH
POWER POWER
PL AYPA U S E STOPSKIP/INDEX
SLOW/SEARCH
REW
FF
3
2
1
6
5 4
9
8
7
0
INPUT
SELECT
VCR/TV
F Rec
REC MODE
SUB MENU
CM SKIPTIME SLIP/     JET REW
DIRECTNAVIGATOR
DISPLAY AUDIO
RECSTATUS
TRACKING/V-LOCKTRACKING/V-LOCK
RESETRESET
CANCEL
DRIVE
 SELECT
VCR/TV
RETURN
FUNCTIONS3, 4, 2, 1
ENTERCH, W, X
No DiscFUNCTIONS No Disc
Program
CopyOther Functions
ENTER
RETURN
Off Timer
ChannelSetupDiscVideoAudioDisplayTV Screen
Remote Control CodeClock Settings
6 HoursSet Code 1
Quick StartRestore Default SettingsOn
Setup
VHS
Set Clock Automatically
Auto Clock Setting is complete.
4/4/2007 11:15 AM
DST................... On
Time Zone.......  CST
∫ Adjust Time Zone
Adjust Time  Zone
0j1
i1
M6VP&PC.book  20 ページ  ２００６年２月６日　月曜日　午後３時２０分