Panasonic Dmr E80 Operating Instructions Manual

							51
RQT6984
Advanced operation
This model can play Dolby Digital, but only in two channels. This model does not have a DTS decoder. You must connect a unit with a 
Dolby Digital or DTS decoder to enjoy surround sound.
Recording to digital recording equipment or cassette tapes
Digital recording
You can record the digital signal directly to digital recording equip-
ment (➜Connection [A] above).
[Note]
≥With DVD, the following conditions must be met: a the disc
doesn’t have protection preventing digital recording, and b the
recording equipment can handle signals with a sampling fre-
quency of 48 kHz.
≥You cannot record DTS signals.
≥You cannot record MP3.
When recording DVDs, make the following settings.
V.S.S.: OFF (➜page 41)
PCM Down Conversion: On (➜page 45)
Dolby Digital: PCM (➜page 45)
DTS: Off (➜page 45)Analog recording
You can record to a cassette deck or other recording equipment
(➜Connection [B] above).
There are no limitations on recording analog signals as there are
with digital signals.
Connecting an amplifier or system component
RF IN
RF OUTVHF/UHF
OPTICAL
DIGITAL AUDIO OUT(PCM/BITSTREAM)COMPONENT
VIDEO OUT
(480P/480I)
YPBPRR - AUDIO - L
R - AUDIO - LVIDEO
VIDEOS-VIDEO
S-VIDEO
(L3)(L1)
IN 1 IN 3R - AUDIO - L
R - AUDIO - LVIDEO
VIDEOS-VIDEO
S-VIDEOOUT 1 OUT 2
R - AUDIO - L
AB
OPTICAL IN
 AUX INL
R
Digital connection
Analog connection
OPTICAL
To enjoy multi-channel surround 
sound
Connect an amplifier with a built-in decoder
or a decoder-amplifier combination.
≥Change the settings in “Digital Audio
Output” (➜page 45).
[Note]
≥You cannot use DTS Digital Surround
decoders not suited to DVD.
≥Even if using this connection, output
will be only 2 channels. [DVD-A]To enjoy stereo or Dolby Pro Logic
Connect a digital amplifier or system
component.
≥Change the settings in “Digital Audio
Output” (➜page 45).To enjoy stereo or Dolby Pro Logic
Connect an analog amplifier or system com-
ponent.
Speakers (Example)
Connect three or more speakers 
for surround sound.
Optical digital audio cable
Do not bend sharply when 
connecting.Insert fully, with this 
side facing up. AmplifierAmplifier or system 
component
Audio cable
This unit 
						

							52
RQT6984
Advanced operation
Home Theater
§By using the S video cable instead of the yellow video cable you
may make recordings of higher picture quality.
≥If the audio output of the other equipment is monaural, connect to
L/MONO. (Both left and right channels are recorded when
connected through L/MONO.)
≥When DV equipment is connected, it is not possible to operate the
unit from the other equipment.
≥The picture compression system of the DV equipment you have
connected may differ from that used in this unit. In such cases,
dubbing from this equipment will not be possible.
§By using the S video cable instead of the yellow video cable you
may make recordings of higher picture quality.
[Note]
If audio output on the other equipment is monaural, use a stereo-
monaural conversion cable (not included).
Connecting other video equipment
Connecting to the L2 input terminals on the front 
of the unit
“S-VIDEO IN
L2
VIDEO INAUDIO INL/MONOR
HDD
REC
S VIDEO
OUTAUDIO
OUT VIDEO
OUTLR
Audio/Video 
cable (included) S video cable
§
Other video equipment
Connect to the video and audio output terminals.
yellow white red yellow white red
This unit
Connecting to the input terminals on the rear of 
the unit, L1 and L3
R - AUDIO - L
R - AUDIO - LVIDEO
VIDEOS-VIDEO
S-VIDEO
(L3)(L1)
IN 1 IN 3R - AUDIO - L
R - AUDIO - LOUT 1 OUT 2
S VIDEO
OUTAUDIO
OUTVIDEO
OUTL
R
Other video equipment
Connect to the video and audio output terminals.S video cable
§
red white yellow red white yellow
Audio/Video cable
(included)This unit 
						

							53
RQT6984
Advanced operation
Other antenna connections
Use one of the following connections to suit the antenna lead.
∫A single twin lead
∫A twin lead and a coaxial cable
∫Two twin leads
≥If your television has both lead and coaxial VHF terminals, use the
lead connection to minimize signal loss.Use one of the following connections to suit the antenna terminals
on your television. Refer to the television’s operating instructions.
∫A twin lead and coaxial plug terminal
∫A twin lead terminal
∫Two twin lead terminals
∫Multiple antenna terminals
≥Connect to one of the terminals, then change the television’s
setting as necessary.
Other antenna connection to the unit
300–75 ≠ transformer
(not included)
from the antenna
(Flat)
Twin lead
300 ≠ cableTo this unit’s
RF IN terminal
from the antenna
(Flat)
Tw i n  l e a d
300 ≠ cable
To this unit’s
RF IN terminal (Round)
75 ≠ coaxial cableVHF/UHF band mixer
(not included)
from the antenna
To this unit’s
RF IN terminal 300–75 ≠ transformer
(not included) (Flat)
Twin lead
300 ≠ cable
VHF/UHF band mixer
(not included)
Other antenna connection from the unit 
to the television
VHF/UHF band separator
(not included)Television
75 ≠ coaxial cableVHF
UHF
75 ≠ coaxial cable75–300 ≠ transformer
(not included)Television
VHF or 
UHF
75 ≠ coaxial cableVHF/UHF band separator
(not included)Te l e v i s i o n
VHF
UHF
ANT 2 ANT 1 Split outTelevision
75 ≠ coaxial cable 
						

							54
RQT6984
Reference
Glossary
Bitstream
This is the digital form of multi-channel audio data (e.g., 5.1 chan-
nel) before it is decoded into its various channels.
CPRM (Content Protection for Recordable Media)
CPRM is the copyright protection technology that is used to protect
broadcasts that are allowed to be recorded only once (e.g. some
CATV broadcasts).
Decoder
A decoder restores the coded audio signals on DVDs to normal.
This is called decoding.
Dolby Digital
This is a method of coding digital signals developed by Dolby Labo-
ratories. Apart from stereo (2-channel) audio, these signals can also
be multi-channel audio. A large amount of audio information can be
recorded on one disc using this method.
This unit is set to record using Dolby Digital in all recording modes.
Dolby Pro Logic
A surround system where a 4-channel audio track is recorded as 2
channels and then is restored to 4 channels for play. The surround
channel is monaural and can reproduce up to 7 kHz.
Drive
In the instance of this unit, this refers to the hard disk (HDD) and
DVD. These perform the reading and writing of data. Select them by
pressing the drive select buttons ([HDD] or [DVD]).
DTS (Digital Theater Systems)
This surround system is used in many movie theaters around the
world. There is good separation between the channels, so realistic
sound effects are possible.
Film and video
DVD-Videos are recorded using either film or video. Usually, film is
recorded at 24 frames per second, the rate movies are filmed at,
while video is recorded at 30 frames per second.
Frame still and field still
Frames are the still pictures that go together to make a moving pic-
ture. There are about 30 frames shown each second.
One frame is made up of two fields. A regular television shows these
fields one after the other to create frames.
A still is shown when you pause a moving picture. A frame still is
made up of two alternating fields, so the picture may appear blurred,
but overall quality is high.
A field still is not blurred, but it has only half the information of a
frame still so picture quality is lower.Hard disk drive (HDD)
This is a mass data storage device used in computers etc. A disk
with a surface that has been treated with magnetic fluid is spun and
a magnetic head is brought in close proximity to facilitate the read-
ing and writing of large amounts of data at high speed.
Interlace and progressive output
NTSC, the video signal standard, has 480 interlaced (I) scan lines,
whereas progressive scanning uses twice the number of scan lines.
This is called 480P. The video signals output from this unit’s COM-
PONENT VIDEO OUT terminals (Y, P
B, PR) allow you to enjoy higher
quality pictures than if the signals were output from the VIDEO OUT
terminal or S-VIDEO OUT terminal.
I/P/B
MPEG 2, the video compression standard adopted for use with
DVD-Video, codes frames using these 3 picture types.
I:Intra coded picture
This picture has the best quality and is the best to use when
adjusting the picture.
P:Predictive coded picture
This picture is calculated based on past I- or P-pictures.
B:Bidirectionally-predictive coded picture
This picture is calculated by comparing past and future I- and
P-pictures so it has the lowest volume of information.
Linear PCM (pulse code modulation)
These are uncompressed digital signals. This unit outputs linear
PCM sound in 2 channels from the DIGITAL AUDIO OUT terminal.
LPCM sound is available when recording in XP mode.
Playback control (PBC)
If a Video CD has playback control, you can select scenes and infor-
mation with menus.
Pan&Scan/Letterbox
In general, DVD-Video are produced with the intention that they be
viewed on a widescreen television with an aspect ratio of 16:9. This
means you can view most material with the intended aspect ratio on
a widescreen television. 
Material with this ratio will not fit onto a standard television with an
aspect ratio of 4:3. Two styles of picture, “Pan&Scan” and “Letter-
box”, deal with this problem.
Pan&Scan:The sides are cut off so the picture
fills the screen.
Letterbox: Black bands appear at the top and
bottom of the picture so the picture
itself appears in an aspect ratio of
16:9.
Do not use irregularly shaped
discs, such as heart-shaped.
(These can damage the unit.)
∫How to hold a discDo not touch the recorded 
surface.
∫If there is dirt or condensation on the discMoisture may condense on discs after they are brought inside from
the cold.
DVD-RAM and DVD-R
Clean with an optional DVD-RAM/PD disc cleaner (LF-K200DCA1,
where available).
Do not use cleaners or cloths for CDs to clean DVD-RAM and DVD-R.
DVD-Audio, DVD-Video, Video
CD, CD
Wipe with a damp cloth and then 
wipe dry.
∫Handling precautions≥Do not write on the label side with a ball-point pen or other writing
instrument.
≥Do not use record cleaning sprays, benzine, thinner, static electric-
ity prevention liquids or any other solvent.
≥Do not attach labels or stickers to discs. (Do not use discs with
exposed adhesive from tape or left over peeled-off stickers.)
≥Do not use scratch-proof protectors or covers.
≥Do not use discs printed with label printers available on the mar-
ket.
≥Do not use discs that are badly warped or cracked.
Disc handling 
						

							55
RQT6984
Reference
Error messages
On the televisionPage
On the unit’s display
No disc.≥You haven’t inserted a disc. Correctly insert a disc that this unit can use. 
≥The disc is upside down. If it is a single-sided disc, insert it so the label is facing up. 10
14
This is non-recordable disc.≥The unit cannot record on the disc you inserted. Insert a DVD-RAM or unfinalized DVD-R. 
≥You inserted an unformatted DVD-RAM. Format the disc with this unit.10
36
This disc is not formatted 
properly.
Please format the disc in ‘DISC 
SETTING’ to record.
This disc cannot be read.≥You inserted an incompatible disc.10
Please check write protect tab 
on the disc.≥The write-protect tab on the cartridge is set to PROTECT.
Use a ballpoint pen or similar to release the write protection.
—
Contents of this disc are pro-
tected.≥The program is write-protected. Cancel the protection.
≥The disc is write-protected. Cancel Disc Protection.34
36
Cannot finish recording com-
pletely.≥The program was copy-guarded. 
≥No space left on HDD or the disc.
‹ Create space by erasing any unwanted programs. [HDD] [RAM]
‹ Use a new disc. [RAM] [DVD-R]
≥Recording was not completed for some other reason.—
34
—
—
Cannot record on the disc.≥The disc is scratched. Use another disc.
≥The disc is dirty.
≥You inserted an incompatible disc.—
54
10
HDD is full.
Disc is full.≥No space left on HDD or the disc.
‹ Create space by erasing any unwanted programs. [HDD] [RAM]
‹ Use a new disc. [RAM] [DVD-R]34
—
Cannot dub from this disc.≥Dubbing prohibited disc in tray.‹ Dubbing to the HDD is not possible. —
Please set clock.≥The clock is not set.47
This disc may not be played in 
your region.≥You tried to play a disc with a region number different from this unit’s region number. This unit
can only play discs with the region numbers compatible with this unit (1, All, or including the
number 1). Cover 
page
Your selection exceeds the 
recorder’s rating limit.≥A ratings level has been set for DVD-Video with this unit. Unlock the unit with “Ratings” in
“Disc”.44
Finalizing is necessary for 
compatible playback.≥To enable playback of your DVD-R on compatible equipment, it is necessary to finalize it.
36
Please check write protect tab.≥Release the protection on the DVD-RAM.10
Error has occurred. Please 
press ENTER.≥A serious, but temporary error has occurred and one of the unit’s safety devices has activated. 
Press [ENTER]. The unit switches to the standby mode. Press [Í, DVD POWER] to turn the
unit on again.—
PROTECT
NO READ≥The disc is dirty or badly scratched.
‹Clean the disc if it is dirty. 
‹The disc cannot be played if it is scratched and this display doesn’t disappear.
≥The unit cannot read the disc.
≥You have used a DVD-RAM/PD lens cleaner and it has finished.54
—
—
58
UNSUPPORT≥You have inserted a disc the unit cannot play or record on.10
U14≥The unit is hot.
‹The unit switches to standby automatically for safety reasons and you cannot operate it.
Wait for about 30 minutes for the service number to disappear.
‹Select a position with good ventilation when installing the unit.
‹Do not block the cooling fan on the rear of the unit.—
—
—
U99≥The unit fails to operate properly. Press [Í, DVD POWER] to switch the unit to standby. Now
press [Í, DVD POWER] again to turn the unit on.—
∑ CHK REMOTE
(“∑” stands for a number.)≥The remote control and main unit are using different codes. Change the code on the remote
control or main unit. 46
RECOVER≥There was a power failure or the AC plug was disconnected while the power was on. The unit is
carrying out its recovery process. Wait until the message disappears. — 
						

							56
RQT6984
Reference
Troubleshooting guide
Before requesting service, make the below checks. If you are in doubt about some of the check points, or if the remedies indicated in the chart do
not solve the problem:
In the U.S.A., contact the Panasonic Customer Call Center at 1-800-211-7262, or e-mail [email protected], 
or the website (http://www.panasonic.com).
In Canada, contact the Panasonic Canada Inc. Customer Care Centre at 1-800-561-5505, or visit the website (www.panasonic.ca), 
or an authorized Servicentre closest to you.
PowerPage
Operation
Picture
≥When progressive output is on, refer also to “Progressive video” below.
Progressive video
No power.≥Insert the AC power supply cord securely into a known active AC outlet.5
The unit switches to the 
standby mode.≥This is a power saving feature. You can turn it off if you would prefer (Set Up—Off Timer—
Off). Press [Í, DVD POWER] to turn the unit on.
≥One of the unit’s safety devices may have activated. Press [Í, DVD POWER] to turn the unit
on.44
—
The unit is on but cannot be 
operated.≥Some operations may be prohibited by the disc.
≥Recording drive or playback drive have not been selected properly.
≥The unit is hot (“U14” appears on the display). Wait for “U14” to disappear.
≥One of the unit’s safety devices may have activated.
Reset the unit as follows:
1.Press [Í, DVD POWER] to switch the unit to standby.
If the unit doesn’t switch to standby, press and hold [Í, DVD POWER] for about 10
seconds. The unit is forcibly switched to standby.
Alternatively, disconnect the AC power supply cord, wait one minute, then reconnect it.
2.Press [Í, DVD POWER] to turn the unit on.—
14, 18
55
—
Cannot eject disc.≥The unit may have a problem. With the power off, press and hold [∫] and [X, CH] at the same
time on the main unit for about 5 seconds. Remove the disc and consult the dealer.—
The images from this unit do 
not appear on the television.≥Make sure that the television is connected to the AUDIO/VIDEO terminal, S-VIDEO OUT
terminal or COMPONENT VIDEO OUT terminal on this unit.
≥Make sure that the television’s input setting (e.g., VIDEO 1) is correct.
≥When using this unit for the first time, the HDD has nothing recorded on it. You must record a
program etc. to the HDD before you can enjoy playback.
≥You have set “TV Type” to “4:3 (480P)” or “16:9 (480P)”  in the TV Screen menus, but the
television isn’t compatible with progressive signals. Press and hold [∫] and [TIME SLIP] on
the unit at the same time for about 5 seconds. The setting will change to interlace.5
—
14
—
Television reception worsens 
after connecting the unit.≥This can occur because the signals are being divided between the unit and the television. 
It can be solved by using a signal booster, available from audio-visual suppliers. Consult your
dealer if reception does not improve.
≥Due to inherent characteristics of the HDD, the picture may occasionally be disturbed. This is
normal.—
—
Screen size is wrong.≥Check the settings on your television.
≥Check the settings for “TV Type”, “4:3 TV Settings for DVD-Video” or “4:3 TV Settings for
DVD-RAM” in the TV Screen menu.—
9, 45
On-screen messages do not 
appear.≥Go to the Display menu and select “Automatic” for “Status Messages”. 
≥Press [STATUS] to show the on-screen messages constantly. 45
43
The blue background does 
not appear.≥Go to the Display menu and select “On” for “Blue Background”.45
There is ghosting.≥Change the settings for “3D NR”, “Block NR”, and “Mosquito NR” to “0” or turn “MPEG-DNR”
off if it is on.41, 42
Play stops for a moment dur-
ing Quick View.≥Play may stop where two play lists join, but this is not a malfunction.—
There is ghosting when pro-
gressive output is on.≥Set “Progressive” to “OFF”. This problem is caused by the editing method or material used on
DVD-Video, but should be corrected if you use interlace output.41
There is no apparent change 
in picture quality when 
adjusted with the Video menu 
in the on-screen menus.≥The effect is less perceivable with some types of video.— 
						

							57
RQT6984
Reference
SoundPage
Play
Displays
Remote controlNo sound.
Low volume.
Distorted sound.≥Check the connections. Check the input mode on the amplifier if you have connected one.
≥Turn V.S.S. off if it causes distortion. 5, 
50–52
41
Cannot hear the desired 
audio type.≥Press [AUDIO] to select the desired audio type.
≥If “D.MIX” does not appear in the display when playing multi-channel DVD-Audio, audio output
will be the front two speakers only.
≥You cannot change the DVD-Audio audio type if the software producer has restricted play in
stereo.39
13
—
Cannot switch audio during 
stereo or SAP broadcasts.≥You have used digital connection. Set “Dolby Digital” to “PCM” or connect to other equipment
using audio cables (analog connection).
≥You cannot change the audio type when a DVD-R is in the disc tray.
≥It is not possible to switch the audio when the recording mode is XP and “LPCM” has been
selected in the SETUP menu, “Audio Mode for XP Recording”.
‹ Select “Main” or “SAP” from “Select MTS” in the Audio menu before recording.45, 51
—
45
Play fails to start even when 
[1] (PLAY) is pressed.
Play starts but then stops 
immediately.≥Insert the disc correctly with the label facing up.
≥This unit cannot play discs other than DVD-RAM, DVD-R, DVD-Audio, DVD-Video, Video CD,
CD and MP3 discs.
≥The disc is dirty. Clean it.
≥The disc may be badly scratched.
≥You inserted a blank DVD-RAM or DVD-R.14
10
54
—
—
A title or chapter doesn’t play 
when it is selected.≥Some titles and chapters on DVD-Video are not played when you have changed the ratings
level.44
Picture distorted during 
search.≥Some distortion is normal.—
Alternative soundtrack and 
subtitles cannot be selected.≥The languages are not recorded on the disc.
≥You may have to use the disc’s menus to select languages.—
19
No subtitles.≥Subtitles are not recorded on the disc.
≥Turn the subtitles on.—
40
Angle cannot be changed.≥This function depends on software availability. Angles can only be changed during scenes
where different angles are recorded.—
You have forgotten your rat-
ings password.≥Return the ratings setting to “8”.
While the disc tray is open, press and hold [:/6] and [5/9] on the main unit at the
same time for 5 or more seconds.—
The display is dim.≥Go to the Display menu and change the display’s brightness with “FL Display”. 45
“12:00” is flashing on the 
unit’s display.≥The clock is not set.47
The displayed recording time 
and actual recording time dif-
fer.≥Displayed recording time is based on the number of frames per second. This number is sub-
ject to minute variations. When recording over long periods, these variations may result in the
difference between displayed recording time and actual recording time. This is normal.—
The display doesn’t show the 
correct time. [MP3]≥Times may not appear correctly when searching through tracks recorded with a variable bit
rate.—
The remote control doesn’t 
work.≥[DVD, TV] is not switched to “DVD”. Switch to “DVD” when operating this unit.
≥The remote control and main unit are using different codes. Change the code on the remote
control or main unit.
≥The batteries are depleted. Replace them with new ones.
≥Point the remote control at the remote control sensor on the main unit.
≥Remove obstacles from between the remote control and main unit.12
46
6
6
—
Cannot operate the televi-
sion.≥Change manufacturer code. Some televisions cannot be operated even if you change the
code.
≥[DVD, TV] is not switched to “TV”. Switch to “TV” when selecting the receiving channel for the
television. 9
12 
						

							58
RQT6984
Reference
Troubleshooting guide
Recording and timer recordingPage
The precision parts in this unit are readily affected by the envi-
ronment, especially temperature, humidity, and dust. Cigarette
smoke also can cause malfunction or breakdown.
To clean this unit, wipe with a soft, dry cloth.
≥Never use alcohol, paint thinner or benzine to clean this unit.
≥Before using chemically treated cloth, read the instructions that
came with the cloth carefully.Observe the following points to ensure continued listening and
viewing pleasure.
Dust and dirt may adhere to the unit’s lens over time, making it
impossible to record or play discs. 
Use the DVD-RAM/PD lens cleaner (LF-K123LCA1) about once
every year, depending on frequency of use and the operating envi-
ronment. Read the lens cleaner’s instructions carefully before use. Cannot record.≥You haven’t inserted a disc or the disc you inserted cannot be recorded on. Insert a disc the
unit can record onto.
≥The disc is unformatted. Format the disc so this unit can record on it. [RAM]
≥The write-protect tab on the cartridge is set to PROTECT.
≥Some programs have limitations on the number of times they can be recorded (CPRM).
≥The disc is protected with DISC SETTING.
≥The HDD or the disc is full or nearly full. Erase unneeded programs or use another disc.
≥You cannot record on finalized DVD-R discs.10
36
10
15
36
34
—
VCR Plusr programming 
does not work properly.≥The guide channels are incorrect. Go to the Channel menu and correct them with “VCR
Plusi CH Setting”.
≥The clock is wrong. Go to the Set Up menu and correct it with “Clock Settings”.8
47
Timer recording does not 
work properly.≥The timer program is incorrect. Correct the program. 
≥Different timer program times overlap.
≥The clock is wrong. Go to the Set Up menu and correct it with “Clock Settings”. 27
—
47
The unit switches to standby 
while making a timer record-
ing.≥The disc has run out of space. Use a disc that has enough space to record the program.—
The timer program remains 
even after recording finishes.≥The program remains if you select “DAILY” or “WEEKLY”. 25
Timer recording does not 
stop even when [∫] is 
pressed.≥Press [∫] and then [ENTER] within 5 seconds to turn “F” off. Recording stops.—
The available recording time 
doesn’t increase even after 
erasing recordings on the 
disc. ≥As this unit is unable to erase data written to DVD-RAM with a computer, the available record-
ing time does not increase. The data will be erased if you reformat the disc.
≥If the disc is dirty, wipe with the DVD-RAM/PD disc cleaner (optional) before formatting. 
≥Available recording space on the DVD-R does not increase even after erasing previously
recorded programming.36
54
—
A part or whole of a recorded 
program has been lost.≥If there is a power failure or the plug is disconnected from the household AC outlet while
recording or editing, the program may be lost or the HDD/disc may become unusable.
‹ We cannot offer any guarantee regarding lost programs or discs. You will have to format
the HDD/disc or use a new disc.—
Cannot dub to a DVD-R disc 
using the high speed mode.≥When recording to the HDD, set “DVD-R compatible Rec” to “On” from the Disc menu. Note
that you cannot dub programs to a DVD-R disc using the high speed mode if you recorded the
program on a DVD recorder that does not have the “DVD-R compatible Rec” function, even
when dubbing to the HDD with this setting “On”.44
Discs make sounds as they rotate. This does not indicate a malfunction.
Maintenance 
						

							59
RQT6984
Reference
Specifications
Recording system:DVD video recording standards
(DVD-RAM),
DVD video standards (DVD-R)
Optical pick-up:System with 1 lens, 2 integration
units (662 nm wavelength for DVDs,
790 nm wavelength for CDs)
Recordable discs:12 cm (5
q) 4.7 GB DVD-RAM discs
12 cm (5q) 9.4 GB DVD-RAM discs
8 cm (3
q) 2.8 GB DVD-RAM discs
12 cm (5
q) 4.7 GB DVD-R discs
8 cm (3q) 1.4 GB DVD-R discs
(for General Ver. 2.0)
Recording time:≥Max. 6 hours (using 4.7 GB disc)
XP: 60 minutes
SP: 120 minutes
LP: 240 minutes
EP: 360 minutes
≥Max. 106 hours (using built-in HDD)
XP: 17 hours
SP: 34 hours
LP: 68 hours
EP:106 hours 
(Continuous 
Recording time is 
6 hours max.
)
Discs played:12 cm (5
q) 4.7 GB DVD-RAM discs
12 cm (5q) 9.4 GB DVD-RAM discs
8 cm (3
q) 2.8 GB DVD-RAM discs
12 cm (5
q) 4.7 GB DVD-R discs
8 cm (3q) 1.4 GB DVD-R discs
(for General Ver. 2.0)
DVD-VIDEO discs
CD-Audio discs (CD-DA)
Video CD discs
DVD-AUDIO discs
CD-R/CD-RW discs
(CD-DA, Video CD, MP3 formatted
discs)
Video system
TV system:NTSC system, 525 lines, 60 fields
Recording system:MPEG2 (Hybrid VBR)
Input:LINE (pin jack)a3, 1.0 Vp-p; 75 ≠
S connectora3 Y: 1.0 Vp-p; 75 ≠
C: 0.286 Vp-p; 75 ≠
Output:LINE (pin jack)a2, 1.0 Vp-p; 75 ≠
S connectora2 Y: 1.0 Vp-p; 75 ≠
C: 0.286 Vp-p; 75 ≠
Component video output (480P/480i):
Y: 1.0 Vp-p; 75 ≠
P
B: 0.7 Vp-p; 75 ≠
P
R: 0.7 Vp-p; 75 ≠
Antenna reception input:
TV Channel: 2ch–69ch, 75 ≠
CATV Channel: 1ch–125ch, 75 ≠Audio system
Recording system:Dolby Digital (XP/SP/LP/EP)
LINEAR PCM (XP mode only)
Input:LINE (pin jack)a3
Reference input: 309 mVrms
FS: 2 Vrms (1 kHz, 0 dB)
Input impedance: 47 k≠
Output:LINE (pin jack)a2
Reference output: 309 mVrms
FS: 2 Vrms (1 kHz, 0 dB)
Output impedance: 1 k≠
(Load impedance: 10 k≠)
Number of channels:Recording: 2 channels
Playback: 2 channels
Other input/output connectors:
Digital audio optical output connector
(PCM, Dolby Digital, DTS)
Operating temperature range:
5 oC–40 oC (41 oF–104 oF)
Operating humidity range:
10 %–80 % RH (no condensation)
Clock unit:Quartz-controlled 12-hour digital dis-
play
LASER Specification
Class I LASER Product
Wave Length:775–815 nm 655–666 nm
Laser Power:No hazardous radiation is emitted with
the safety protection
Power supply:AC 120 V, 60 Hz
Power consumption:35 W
Dimensions:Approx. 430 (W)k79 (H)k300 (D) mm
[Approx.1615/16q(W)k31/8q(H)k1113/16q(D)](excluding protrusions)
Mass:Approx. 4.5 kg (9.92 lbs)
[Note]
Specifications are subject to change without notice.
Mass and dimensions are approximate.
1.Damage requiring service—The unit should be serviced by
qualified service personnel if:
(a)The AC power supply cord or AC adaptor has been damaged;
or
(b)Objects or liquids have gotten into the unit; or
(c)The unit has been exposed to rain; or
(d)The unit does not operate normally or exhibits a marked
change in performance; or
(e)The unit has been dropped or the cabinet damaged.
2.Servicing—Do not attempt to service the unit beyond that
described in these operating instructions. Refer all other servic-
ing to authorized servicing personnel.3.Replacement parts—When parts need replacing ensure the
servicer uses parts specified by the manufacturer or parts that
have the same characteristics as the original parts. Unauthorized
substitutes may result in fire, electric shock, or other hazards.
4.Safety check—After repairs or service, ask the servicer to per-
form safety checks to confirm that the unit is in proper working
condition.
For product information or assistance with product operation:
In the U.S.A., contact the Panasonic Customer Call Center at
1-800-211-7262, or e-mail [email protected], 
or the website (http://www.panasonic.com).
In Canada, contact the Panasonic Canada Inc. Customer Care 
Centre at 1-800-561-5505, or visit the website
(www.panasonic.ca), or an authorized Servicentre closest to you.
Power consumption in standby mode: approx. 3.3 W
Product Service
Product information 
						

							Reference
60
RQT6984
Limited Warranty (ONLY FOR U.S.A.)
Panasonic Consumer Electronics Company,
Division of Matsushita Electric Corporation of America
One Panasonic Way Secaucus, New Jersey 07094Panasonic Sales Company, Division of Matsushita Electric 
of Puerto Rico, Inc.,
Ave. 65 de Infantería, Km. 9.5
San Gabriel Industrial Park, Carolina, Puerto Rico 00985
Panasonic DVD Recorder
Limited Warranty
Limited Warranty Coverage
If your product does not work properly because of a defect in materials or workmanship, 
Panasonic Consumer Electronics Company or Panasonic Sales Company (collectively 
referred to as “the warrantor”) will, for the length of the period indicated on the chart below, 
which starts with the date of original purchase (“warranty period”), at its option either (a) 
repair your product with new or refurbished parts, or (b) replace it with a new or a refurbished 
product. The decision to repair or replace will be made by the warrantor.
During the “Labor” warranty period there will be no charge for labor. During the “Parts” 
warranty period, there will be no charge for parts.  You must carry-in or mail-in your product 
during the warranty period. If non-rechargeable batteries are included, they are not 
warranted. This warranty only applies to products purchased and serviced in the United 
States or Puerto Rico. This warranty is extended only to the original purchaser of a new 
product which was not sold “as is”. A purchase receipt or other proof of the original purchase 
date is required for warranty service.
Carry-In or Mail-In Service 
For Carry-In or Mail-In Service in the United States call 1-800-211-PANA (7262) or visit 
Panasonic Web Site: http://www.panasonic.com
For assistance in Puerto Rico call Panasonic Sales Company (787)-750-4300 or fax 
(787)-768-2910. Limited Warranty Limits And Exclusions
This warranty ONLY COVERS failures due to defects in materials or workmanship, and DOES 
NOT COVER normal wear and tear or cosmetic damage. The warranty ALSO DOES NOT 
COVER damages which occurred in shipment, or failures which are caused by products not 
supplied by the warrantor, or failures which result from accidents, misuse, abuse, neglect, 
mishandling, misapplication, alteration, faulty installation, set-up adjustments, misadjustment 
of consumer controls, improper maintenance, power line surge, lightning damage, 
modification, or commercial use (such as in a hotel, office, restaurant, or other business), 
rental use of the product, service by anyone other than a Factory Servicenter or other 
Authorized Servicer, or damage that is attributable to acts of God.
THERE ARE NO EXPRESS WARRANTIES EXCEPT AS LISTED UNDER 
“LIMITED WARRANTY COVERAGE”. THE WARRANTOR IS NOT LIABLE 
FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM 
THE USE OF THIS PRODUCT, OR ARISING OUT OF ANY BREACH OF THIS 
WARRANTY. (As examples, this excludes damages for lost time, travel to and 
from the servicer, loss of media or images, data or other recorded content. The 
items listed are not exclusive, but are for illustration only.) ALL EXPRESS AND 
IMPLIED WARRANTIES, INCLUDING THE WARRANTY OF 
MERCHANTABILITY, ARE LIMITED TO THE PERIOD OF THE LIMITED 
WARRANTY.
Some states do not allow the exclusion or limitation of incidental or 
consequential damages, or limitations on how long an implied warranty lasts, so 
the exclusions may not apply to you.
This warranty gives you specific legal rights and you may also have other rights 
which vary from state to state. If a problem with this product develops during or 
after the warranty period, you may contact your dealer or Servicenter. If the 
problem is not handled to your satisfaction, then write to the warrantor’s 
Consumer Affairs Department at the addresses listed for the warrantor.
PARTS AND SERVICE WHICH ARE NOT COVERED BY THIS LIMITED 
WARRANTY ARE YOUR RESPONSIBILITY.
Product or Part Name Parts Labor
DVD Recorder One (1) Year One (1) Year
Rechargeable Batteries, 
DVD-RAM Disc (in 
exchange for defective 
item)Ten (10) Days Not Applicable
F0602NY
Customer Services Directory
For Product Information, Operating Assistance, Literature Request,
Dealer Locations, and Customer Service inquiries please visit Web Site:
http://www.panasonic.com
You can purchase parts, accessories, locate your nearest servicenter and more by visiting our 
Web Site
or E-mail us via web:
http://www.panasonic.com/consumer_electronics/support/customerfeedback.asp
Contact:
1-800-211-PANA (7262),
Monday–Friday 9 am–9 pm; Saturday–Sunday 10 am–7 pm, EST.
For hearing or speech impaired TTY users, 
TTY: 1-877-833-8855
Accessory Purchases
1-800-332-5368 (Customer Orders Only)
1-800-237-9080 (Fax Only)
(Monday–Friday 9 am to 8 pm, EST.) Panasonic Services Company
20421 84th Avenue South, Kent, WA 98032
(Accepts Visa, MasterCard, Discover Card, American Express, and Personal Check)For hearing or speech impaired TTY users,
TTY: 1-866-605-1277
Service in Puerto Rico
Matsushita Electric of Puerto Rico, Inc. Panasonic Sales Company/Factory Servicenter:
Ave. 65 de Infanteria, Km. 9.5, San Gabriel Industrial Park, Carolina, Puerto Rico 00985
Phone (787) 750-4300    Fax (787) 768-2910
User memo:
The model number and serial number of this product can be
found on either the back or the bottom of the unit.
Please note them in the space provided below and keep for
future reference.
MODEL NUMBER
SERIAL NUMBER
DMR-E80H
DATE OF PURCHASE
DEALER NAME
DEALER ADDRESS
TELEPHONE NUMBER