Panasonic Dmp Bdt300 Operating Instructions

							31VQT2J87(ENG)
Settings
Dynamic Range Compression
You can listen at low volumes but still hear dialog clearly.
(Dolby Digital, Dolby Digital Plus and Dolby TrueHD only)
≥“Auto” is effective only when playing Dolby TrueHD.
Digital Audio Output (>38)
Press [OK] to show the following settings:
PCM Down Conversion
Select how to output audio with a sampling frequency of 
96 kHz for the PCM output from the DIGITAL AUDIO OUT.
≥If “ On ” is selected, the  signals that are converted to 48 kHz 
are output.
≥ If “Off” is selected, and the connected equipment does not 
support 96 kHz, the sound will not be output normally.
≥ Signals are converted to 48 kHz despite the settings in the 
following cases:
– when the signals have a sampling frequency of 192 kHz
– when the disc has copy protection
– when “BD-Video Secondary Audio” is set to “On”
Downmix
Select the downmix system of multi-channel to 2 channel 
sound.
≥Select “ Surround encoded ”, when the connected equipment 
supports the virtual surround function.
≥ There is no effect on “Bitstream” via HDMI AV OUT and 
DIGITAL AUDIO OUT.
≥ The audio will be output in “Stereo” in the following cases;
– AVCHD playback
– Playback of secondary audio (including the button click 
sound).
7.1ch Audio ReformattingSurround sound with 6.1ch or less  is automatically expanded 
and played back at 7.1ch.
≥ If “Off” is selected, sound is  played over the original number 
of channels. (Note that in the case of 6.1ch audio, playback 
will be at 5.1ch.)
Audio reformatting is enabled in the following cases:
≥ When you have selected “PCM” in “Digital Audio Output”.
≥ When the audio is Dolby Digital, Dolby Digital Plus, Dolby 
TrueHD or LPCM.
High Clarity Sound
When connected to TV via the HDMI terminal for outputting 
image, it produces clearer sound.
≥Set to “Enable” and then set “High Clarity Sound” on the 
Playback menu to “On”. ( >29)
Audio Delay
Mis-sync between the video and audio is corrected by 
delaying the audio output.
Status Messages
Choose whether to show status messages automatically.
On-screen Language
Choose the language for menus and on-screen messages.
Screen Saver Function
This is to prevent  burn-in on the screen.
≥ When this is set to “On”:
If there is no operation for 10 minutes or more, Direct 
Navigator screen switches  to FUNCTIONS screen 
automatically.
≥ While playing and pausing, etc., this function is not 
available.
≥ As for Music [CD-DA] or MP3, regardless of the setting, if 
there is no operation for a while, Direct Navigator screen 
switches to the other states automatically.
FL Display
Changes the brightness of the unit’s display.
≥If “Auto” is selected the display is dimmed during playback 
and bright not during playback.
SD Card LED Control
Set the lighting method for the SD card LED.
≥If “SD inserted” is selected, and this unit is turned on and 
SD card is inserted, the lamp is lighted.
HDMI(SUB) V.OFF LED Control
Set to light the HDMI (SUB) V.OFF LED or not.
≥This will light when “HDMI(SUB) Output Mode” ( >32) is set 
to “V.OFF”, and the power of the connected equipment to 
the HDMI SUB AV OUT is on.
License
Information about the software used by this unit is displayed. 
Audio
Dolby D/Dolby D +/Dolby TrueHD
DTS/DTS-HD
Select the audio signal to output.≥ Select “PCM ”, when the connected equipment cannot 
decode the respective audio format.
≥ Not making the proper settings may result in noise.
BD-Video Secondary AudioSelect whether to mix or not mix the primary audio and
secondary audio (including the button click sound).  (> 21)
≥ If “ Off ” is selected, the unit outputs the primary audio only.
Display
VQT2J87~Body_eng.fm  31 ページ  ２０１０年１月２６日　火曜日　午後２時４１分 
						

							32VQT2J87(ENG)
3D TypeSelect the format of the connected TV.
≥Change the settings for 3D on the TV also when “Checker 
board” and “Side by side” are selected.
TV Aspect
Set to match the type of television connected.
HDMI Connection
Press [OK] to show the following settings:
Component Video Resolution
This sets the video output resolution when connected via the 
COMPONENT VIDEO OUT terminal.
≥
Even if you select “720p” or “1080i”, the video output 
resolution is restricted to “480p” when images of DVD-Video 
discs are output from the COMPONENT VIDEO OUT 
terminals.
Analog Audio Output
You can set the optimum multi-channel surround sound
for your speakers from this unit when the settings cannot be 
adjusted from a connected amplifier/receiver with AUDIO 
OUT terminals.
Select “2ch (Downmix) + 5.1ch” or “7.1ch” and press [OK], 
and then set the following options.
– Speaker presence and size ( )
– Delay time ( )
– Channel balance ( )
To finish the speaker setting
Press [ 3,4, 2,1 ] to select “Complete” and press [OK].
TV / Device Connection
When connected to a 4:3 aspect television and playing 16:9 
ratio image:
4:3 Pan & 
Scan
The sides are cut off so 
the picture fills the screen. 
When playing BD-Video, 
video is output as “4:3 
Letterbox”.
4:3 Letterbox
Black bands appear at the 
top and bottom of the 
picture.
When connected to a 16:9 widescreen television and 
playing 4:3 ratio image:
16:9Video is displayed as a 4:3 ratio image in the 
center of the screen.
16:9 FullVideo is displayed as a horizontally 
stretched 16:9 image.
HDMI Video ModeSelect “On” when video is output from HDMI AV OUT 
terminal.
OnImages are output from the HDMI terminal in the 
resolution set in “HDMI Resolution”.
OffImages are output in the resolution set in 
“Component Video Resolution”.
HDMI(SUB) Output ModeSet to output the video from the HDMI SUB AV OUT 
terminal or not.
HDMI ResolutionThe items supported by the connected devices are 
indicated on the screen as “ ¢”. When any item without “ ¢” 
is selected, the images may be distorted.
≥ If “Auto” is selected, automatically selects the output 
resolution best suited to the connected television.
≥ To enjoy high-definition video up-converted to 1080p, you 
need to connect the unit directly to 1080p compatible 
HDTV (High Definition Televisi on). If this unit is connected 
to an HDTV through other equipment, it must also be 
1080p compatible.
24p OutputWhen this unit is connected to a TV supporting 1080/24p 
output using an HDMI cable, movies and other material 
recorded at 24p are output at 24p.
≥ When playing DVD-Video, set to “On” and then also set 
“24p” in “Video” ( >29) to “On”.
≥ When BD-Video images other than 24p are played, 
images are output at 60p.
HDMI Color ModeThis setting is for selecting color-space conversion of the 
image signal when the unit is connected using an HDMI 
cable.
HDMI Audio OutputThis setting selects whether or not to output audio from 
HDMI.
≥Select “Off” when the TV is connected to this unit via an 
HDMI terminal, and this unit is also connected to other 
devices, such as an amplifier/receiver via a COAXIAL or 
an OPTICAL terminal.
VIERA LinkSet to use “HDAVI Control” function when connected with 
an HDMI cable to a device that supports “HDAVI Control”.
≥Select “Off” when you do not want to use “HDAVI Control”.
Deep Color OutputThis setting is for selecting whether to use Deep Color 
output when a television that supports Deep Color is 
connected.
Contents Type FlagDepending on the playback content, the TV will output 
adjusting to the optimal method when a TV that supports 
this function is connected.
LLSRSWRSLBRBC
ms0.0
dB0.0
DMP-BDT300_VQT2J87_eng.book  32 ページ  ２０１０年１月２６日　火曜日　午後１時５２分 
						

							33VQT2J87(ENG)
Settings
Network Easy Setting (>15)
Network Settings
Perform network-related settings individually.
Press [OK] to show the following settings:
Off Timer
Select how long the unit remains on when it is not being used.
Remote Control Code
Change the remote control code, when other Panasonic 
products react to this remote control.
Quick Start
Speed of startup from power off is increased.
≥Internal control unit will be powered when it is set to “On”, so 
contents of the following will be different from the time it is 
set to “Off”.
– Idle power consumption will  increase. (about the power 
consumption  >43)
– The cooling fan may turn slowly to prevent overheating of  internal parts.
Easy Setting
You can execute basic sett ings (“On-screen Language”, “TV 
Aspect”, “Analog Audio Output”, “Quick Start”)
Restore Default Settings
This returns all values in the Setup menu and the Playback 
menu, except for “Remote Control Code”, “On-screen 
Language”, “IP Address/DNS Sett ings”, “Proxy Server 
Settings”, “Lock”, “DVD-Video Ratings” and “BD-Video 
Ratings” to the default settings.
DivX Registration (>22)
You need this registration code to purchase and play DivX 
Video-on-Demand (VOD) content.
System Information
Display firmware version of this unit, wireless LAN module of 
your Wireless LAN Adaptor.
Firmware Update (>17)
Press [OK] to show the following settings:
Network
LAN Connection ModeSelect connection method.
Access Point Connection SettingThis allows the Wireless router (Access point) and 
connection settings to be set and the current connection 
settings and connection state to be checked when a 
wireless connection is used.
Connection Setting
The Wireless router (Access point) connection wizard will 
be displayed.
Double Speed Mode Setting (2.4GHz)  [BDT350]
When a 2.4 GHz wireless format is used, this setting sets 
the connection speed.
≥ If you connect using the “Double Speed Mode(40MHz)”, 
2 channels use the same frequency band, and there is 
consequently a greater risk of reception interference. 
This can cause the connection speed to drop or the 
connection to become unstable.
IP Address/DNS SettingsThis is for checking the state of the network connection and 
setting the IP address and DNS-related.
Press [OK] to show the respective setting.
≥“Connection Speed Setting” is enabled only when “Auto 
Detect Connection Speed” is turned “Off”.
Proxy Server Settings
This is for checking the state of connection with the Proxy 
server and performing settings.
Press [OK] to show the respective setting.
Internet Content Settings (>25) (VIERA CAST)
Press [OK] to show the following settings:
Lock
You can restrict the usage of VIERA CAST.
≥Follow the on-screen instructions. Enter a 4-digit 
password with the number buttons when the password 
screen is shown. 
Audio Auto Gain Control
Volume that is different depending on the contents is 
adjusted automatically to the standard volume while using 
the VIERA CAST.
≥Depending on contents, this function effect will not work.≥ Select “Off” when the audio is warped.
Time Zone
By selecting the time zone, it is possible to set the unit’s 
time to match your location.
≥ Some VIERA CAST contents require the time zone to 
be set. Set the time zone if necessary.
DST
Select “On” when using Daylight Saving time.
MAC Address
Displays the MAC address of this unit.
Others
Automatic Update CheckWhen this equipment remains connected to the Internet, it 
will check for the latest firmware version when it is turned on 
and you can update it if necessary.
Update NowYou can update the firmware manually.
DMP-BDT300_VQT2J87_eng.book  33 ページ  ２０１０年１月２１日　木曜日　午後８時９分 
						

							34VQT2J87(ENG)
Reference
Troubleshooting guide
Before requesting service, please perform the 
following steps.
The following do not indicate a problem with this unit:
≥Regular disc rotating sounds.
≥ Image disturbance during search.
∫ Unit doesn’t respond to remote control 
or front panel buttons.
Press and hold [POWER  Í/I] on the main unit for 3 seconds.
– If still unable to power the unit off, disconnect the power  cord, wait 1 minute, then reconnect the power cord.
∫ Cannot eject disc.
The unit may have a problem.
1 While the unit is off, press and hold [OK], [B] and [Y] on 
the remote control at the same time for more than 
5 seconds.
– “00 RET” is displayed on the unit’s display.
2 Repeatedly press [ 1] (right) on the remote control or 
[POWER  Í/I] on the unit until “06 FTO” is displayed on 
the units display.
3 Press [OK] on the remote control or [ 33)
To return all settings to the factory preset.
¾Reset the unit as follows:
1 While the unit is off, press and hold [OK], [B] and [Y] on 
the remote control at the same time for more than 
5 seconds.
– “00 RET” is displayed on the unit’s display.
2 Repeatedly press [ 1] (right) on the remote control or 
[POWER  Í/I] on the unit until “08 FIN” is displayed on the 
units display.
3 Press and hold [OK] on the remote control or [ 33)
¾It may be necessary to set the manufacturer code or the 
remote control code again after changing the batteries for 
the remote control. ( >17)
The TV tuner mode is not displayed when the 
TV is switched on.
¾This phenomenon may occur, depending on the TV 
setting, when “Quick Start” is set to “On”.
– Depending on the TV, this phenomenon may be prevented 
by reconnecting the HDMI cable to a different HDMI input 
terminal or by changing the HDMI auto connection setting.
You have forgotten your ratings password.
You want to cancel the ratings level.
¾The ratings level returns to the factory preset.
1 While the unit is on, press and hold [OK], [B] and [Y] on 
the remote control at the same time for more than 
5 seconds.
– “00 RET” is displayed on the unit’s display.
2 Repeatedly press [ 1] (right) on the remote control or 
[POWER  Í/I] on the unit until “03 VL” is displayed on the 
units display.
3 Press [OK] on the remote control or [  17)
4
Make the following checks and visit our 
website for more information.
For USA : 
http://www2.panasonic.com/consumer-electronics/support/
Enter the model number.
For Canada  : 
http://www.panasonic.ca 4
Even so, you still have trouble,
Visit our website to find a service center.You can find a service cent er near you easily on our 
website.
Other support information :
“Customer Services Directory (United States and Puerto 
Rico)” ( >46) or “Limited Warranty (Only for 
CANADA)” ( >47).
General operation
DMP-BDT300_VQT2J87_eng.book  34 ページ  ２０１０年１月２１日　木曜日　午後８時９分 
						

							35VQT2J87 (ENG)
Reference
The images from this unit do not appear on 
the television.
Picture is distorted.
¾An incorrect resolution is selected in “Component Video 
Resolution” or “HDMI Resolution”. Reset the setting as 
follows:
1 While the unit is on, press and hold [OK], [B] and [Y] on 
the remote control at the same time for more than 
5 seconds.
– “00 RET” is displayed on the unit’s display.
2 Repeatedly press [ 1] (right) on the remote control or 
[POWER  Í/I] on the unit until “04 PRG” is displayed on 
the units display.
3 Press and hold [OK] on the remote control or [ 32)
– When Dolby Digital Plus, Dolby TrueHD, and DTS-HD audio  are not output in bitstream, select “Yes” in “Restore Default 
Settings” and make proper settings. ( >33)
Video is not output .
¾Set the “High Clarity Sound” in the Playback menu to “Off” 
to use the COMPONENT VIDEO OUT terminal or the 
VIDEO OUT terminal. ( >29)
¾Video from the HDMI SUB AV OUT terminal is not output 
when the “HDMI(SUB) Output Mode” is set to “V.OFF”. 
(> 32)
Video is not output in high-definition.
¾Confirm that the “HDMI Video Mode”, “HDMI Resolution”, 
and “Component Video Resolution” in the Setup menu are 
set properly. ( >32)
3D video is not output.
¾Is there a non-3D compatible amplifier/receiver connected 
between this unit and a TV? ( >10)
¾If there is a non-3D compatible amplifier/receiver 
connected to the HDMI SUB AV OUT terminal, set the 
“HDMI(SUB) Output Mode” to “V.OFF”. ( >10)
¾Are the settings on this unit and the TV correct? ( >23)¾Is the amplifier/receiver connected to between this unit 
and TV on?
No subtitles.
¾When progressive output is on,  closed captions/subtitles 
cannot be displayed.
The subtitles overlap closed captions 
recorded on discs.
¾Turn off the subtitles or turn off the closed caption setting 
on the TV.  (> 28)
A black band is displayed around the edge of 
the screen.
The aspect ratio of the screen is abnormal.
¾Confirm the “TV Aspect” is set properly. ( >32)¾Adjust the aspect setting on the television.
(Adjustment using “Screen Aspect” ( >20) on the unit is 
also possible)
Cannot switch audio.
¾When connecting an amplifier/receiver using a COAXIAL /
OPTICAL terminal or an HDMI terminal, you cannot 
switch the audio if “Digital Audio Output” is set to 
“Bitstream”. Set “Digital Audio Output” to “PCM” or 
connect using AUDIO OUT terminal. ( >11 , 3 1 )
Cannot hear the desired audio type.
¾Check the connections and the “Digital Audio Output” 
settings. ( >31)
¾When the unit is connected to an amplifier/receiver with 
the AUDIO OUT terminal, set “Analog Audio Output”. 
(> 32)
¾To output audio from a device connected with an HDMI 
cable, set “HDMI Audio Output” to “On” in the Setup 
menu. ( >32)
¾When connecting this unit to a TV via an HDMI MAIN AV 
OUT and to an amplifier/receiver via an HDMI SUB AV 
OUT, set “HDMI(SUB) Output Mode” to “V.OFF”. ( >10)
Picture
Audio
VQT2J87~Body_eng.fm  35 ページ  ２０１０年１月２６日　火曜日　午後２時４１分 
						

							36VQT2J87(ENG)
Disc cannot be played.
¾The disc is dirty. (>4)
The contents of the USB device cannot be 
read.
¾USB devices connected usi ng a USB extension cable 
other than the one included or a USB hub may not be 
recognized by this unit.
¾If inserted during playback the USB device may not be 
recognized by this unit.
¾If two USB devices other than Wireless LAN adaptor are 
connected simultaneously, they  will not be recognized by 
this unit.
Still pictures (JPEG) do not play back 
normally.
¾The images that were edited on the PC, such as 
Progressive JPEG, etc., may not play back.
I can’t play back BD-Live.
¾The SD card is write-protected. ( >7)¾Confirm that this unit is  connected to the broadband 
Internet. ( >12)
¾Confirm the “BD-Live Internet Access” settings. ( >30)¾Confirm an SD Card is inserted into the SD Card slot. 
(> 18)
I can’t connect to the network.
¾Confirm the network connection and settings. ( >12, 33)¾Check the operating instructions for each device and 
connect accordingly.
When using Wireless LAN connection, video 
from the DLNA Certified media server is not 
played back or video frames are dropped 
during playback. 
[BDT350]
¾Higher transfer rate router such as 802.11n (2.4 GHz or 5 
GHz) Wireless router (Access Point) may solve the 
problem. If you use 802.11n (2.4 GHz or 5 GHz) Wireless 
router (Access Point), it is necessary to set the encryption 
type to “AES”.
Simultaneous use with a microwave, cordless telephone 
etc. at 2.4 GHz may result in connection interruptions or 
other problems.
¾On the “Access Point Connection Setting” screen ( >33), 
the continuous lighting of at least 4 “Reception” indicators 
is the target for a stable connection. If 3 or fewer 
indicators are lit or the connection is being interrupted, 
change the position or angle of your Wireless router 
(Access point) and see if the connection state improves. If 
there is no improvement, conn ect to a wired network and 
perform the “Network Easy Setting” ( >15) again. 
PlaybackNetwork
DMP-BDT300_VQT2J87_eng.book  36 ページ  ２０１０年１月２１日　木曜日　午後８時９分 
						

							37VQT2J87 (ENG)
Reference
Messages
The following messages or service numbers appear on the 
television or unit’s display when something unusual is 
detected during startup and use.
Cannot play.¾You inserted an incompatible disc (Discs recorded in PAL 
video, etc.).
Cannot display on this unit.¾You tried to play a non-compatible image.¾Confirm “SD” on the unit’s display is not blinking and 
re-insert the card. 
No disc is inserted.¾The disc may be upside down.
$ This operation is not available.¾Some operations are unsupported by the unit. For 
example;
– BD-Video
: During playback, reverse slow-motion or reverse 
frame-by-frame is not possible.
IP address is not set.¾The “IP Address” in “IP Address/DNS Settings” is “---. ---. 
---. ---”. Set the “IP Address”, “Subnet Mask”, and “Default 
Gateway”. (Select the automatic address acquisition if 
necessary.)
The current security setting of Wireless LAN 
is low. It is recommended to change the 
setting. 
[BDT350]¾Authentication type for the Wireless LAN is set to “Open 
system”, or the encryption type is set to “No encryption”. It 
is recommended to encrypt for safety reasons. For 
details, refer to the instructions of the Wireless router 
being used. Encryption is required when playing back 
video, etc., from DLNA compatible devices.
F99¾The unit fails to operate properly. Press [POWER  Í/I] on 
the main unit to switch the unit to standby for 3 seconds. 
Now press [POWER  Í/I] on the main unit again to turn 
the unit on.
HDMI ONLY¾Some BD-Video discs can only be output with HDMI.
NET¾Displays while VIERA CAST is starting up.
No PLAY¾There is a viewing restriction on a BD-Video or 
DVD-Video. ( >30)
No READ¾The media is dirty or badly scratched. The unit cannot 
play.
PLEASE WAIT¾The unit is carrying out an internal process. This is not a 
malfunction. You cannot operate the unit while “PLEASE 
WAIT” is displayed.
REMOVE¾The USB device is drawing too much power. Remove the 
USB device.
SET  (“   ” stands for a number.)¾The remote control and main unit are using different 
codes. Change the code on the remote control.
Press and hold [OK] and the 
indicated number button at the 
same time for more than 5 
seconds.
U59¾The unit is hot.
The unit switches to standby for safety reasons. Wait for 
about 30 minutes until the message disappears.
Select a position with good ventilation when installing the 
unit. Do not block the cooling fan on the rear of the unit.
U72
U73
¾The HDMI connection acts unusually.
– Turn the unit and TV off. 
– Disconnect the HDMI cable between the player and the 
TV.
H  or F (“   ” stands for a number.)
¾There is something unusual. ¾Check the unit using the troubleshooting guide. If the 
service number does not disappear, do the following. 
1 Disconnect the plug from the AC outlet, wait a few 
seconds, then reconnect it.
2 Press [POWER  Í/I] to turn the power on.
If the service number does not disappear despite doing the 
above, request service from the dealer. Inform the dealer of 
the service number when requesting service.
START¾The system is being restarted during the firmware update. 
Please do not turn off power.
UPD /(“    ” stands for a number.)¾The firmware is being updated.
Please do not turn off power.
FINISH¾The firmware update is complete.
On the television
On the unit’s display
DMP-BDT300_VQT2J87_eng.book  37 ページ  ２０１０年１月１８日　月曜日　午後５時２７分 
						

							38VQT2J87(ENG)
Audio Information
The audio output differs depending on which terminals are connected to the amplifier/receiver, and the settings on the unit. (>31, 
Digital Audio Output)
≥ The number of channels listed is the maximum possible number of output channels.
HDMI AV OUT/DIGITAL AUDIO OUT (Coaxial/Optical)
About audio from audio output terminals
TerminalHDMI AV OUTDIGITAL AUDIO OUT
“Dolby D/Dolby D +/Dolby 
TrueHD”/“DTS/DTS-HD” “Bitstream”*1
*1When the connected equipment is not supported with these audio formats, the audio is output as Dolby Digital bitstream, DTS Dig ital Surround bitstream or 
down-mixed 2ch PCM (e.g., TV).
“PCM”*2
*2When the connected equipment is not supported with multi channel surround, the audio is output as down-mixed 2ch PCM.
“Bitstream”“PCM”
“BD-Video Secondary Audio”“On”*3
*3When playing BD-Video without secondary audio or button click sound, the audio is output as the same format as if “BD-Video Sec ondary Audio” was set to 
“Off”.
“Off”“On”*4
*4When playing BD-Video with secondary audio or button click sound, the audio is output as 5.1ch.
“Off”“On”/“Off”“On”/“Off”
Dolby Digital/
Dolby Digital EX*5
*5With PCM output, Dolby Digital EX becomes PCM audio decoded as Dolby Digital, DTS-ES recorded to DVD-Video becomes PCM audio de coded as DTS 
Digital Surround, and DTS-ES recorded to BD-Video becomes PCM audio decoded as DTS-ES.
Dolby Digital
Outputs using original audio DVD-Video : 5.1ch PCM Dolby Digital/
Dolby Digital 
EX*6
*6When “BD-Video Secondary Audio” is set to “On”, Dolby Digital EX is output as Dolby Digital and DTS-ES is output as DTS Digital Surround, however if 
playing BD-Video without secondary audio or button click sound, the audio is output as the original format.
Down-mixed 2ch PCM
BD-Video : 7.1ch PCM
*7
*7When BD-Video is played and “7.1ch Audio Reformatting” is set to “Off”, the audio is output as 5.1ch.
Dolby Digital Plus/
Dolby TrueHD 7.1ch PCM
Dolby Digital
DTS Digital Surround/
DTS-ES*5DTS Digital Surround DVD-Video : 5.1ch PCM
DTS Digital 
Surround/
DTS-ES*6BD-Video : 7.1ch PCM*8
*8The audio output is amplified from 5.1ch or 6.1ch to 7.1ch depending on the DTS, Inc. specifications.
DTS-HD High Resolution  Audio/
DTS-HD Master Audio 7.1ch PCM*8DTS Digital 
Surround
7.1ch LPCM 7.1ch PCMDown-mixed 2ch PCM
AUDIO OUT
Terminal7.1ch AUDIO OUT5.1ch AUDIO 
OUT2ch AUDIO OUT
“BD-Video Secondary Audio”“On”*4/“Off”“On”/“Off”“On”/“Off”
Dolby Digital/
Dolby Digital EX DVD-Video : 5.1ch
5.1ch 2ch
BD-Video : 7.1ch*7
Dolby Digital Plus/
Dolby TrueHD 7.1ch
DTS Digital Surround/
DTS-ES DVD-Video : 5.1ch
BD-Video : 7.1ch*8
DTS-HD High Resolution  Audio/
DTS-HD Master Audio 7.1ch*8
7.1ch LPCM
7.1ch
DMP-BDT300_VQT2J87_eng.book  38 ページ  ２０１０年１月１８日　月曜日　午後５時２７分 
						

							39VQT2J87 (ENG)
Reference
The settings of the audio output vary depending on the connected equipment. Refer to the table below and set each of the items.
Press [SETUP] > “Audio” > Set each item
For details of the each item, refer to page 31.
Recommended audio output setting
Example of connected equipment
TV via HDMI*1
Receiver with 
HD audio*2 
decoder via  HDMI
Receiver without 
HD audio*2 
decoder via  HDMIReceiver via COAXIAL or  OPTICALReceiver 
via analog output*3Setup menu
“Digital  Audio 
Output”
“Dolby D/Dolby  D +/Dolby 
TrueHD” “PCM” “Bitstream” “PCM”
“PCM”No effect
“DTS/DTS-HD” “PCM” “Bitstream” “PCM” “PCM”No effect
“BD-Video 
Secondary 
Audio” “Off”
“Off”“Off”“Off”“Off”
“PCM Down Conversion” No effect No effect No effect
“Off”*4No effect
“Downmix”“Stereo”No effect No effect
“Stereo”*5No effect
“High Clarity Sound”“Enable”
“Disable”*6“Disable”*6“Disable”*6“Disable”*6
≥Because underlined items are the factory presets,  it is not necessary to change these settings.*1If connected to TV via the COAXIAL, OPTICAL or AUDIO OUT terminal, these settings have no effect.*2HD audio: Dolby Digital Plus, Dolby TrueHD, DTS-HD High Resolution Audio and DTS-HD Master Audio*3Set “Analog Audio Output” to “7.1ch” or “2ch (Downmix) + 5.1ch”. (Press [SETUP] > TV / Device Connection)*4If the connected equipment that does not support 96 kHz, set to “On”.*5If the connected equipment that supports the virtual surround function, set to “Surround encoded”.*6When connected to TV via the HDMI terminal for outputting image, set to “Enable”.
DMP-BDT300_VQT2J87_eng.book  39 ページ  ２０１０年１月２６日　火曜日　午後１時５２分 
						

							40VQT2J87(ENG)
About MP3/JPEG/DivX/
AVCHD/MPEG2 files
	
≥With certain recording states and folder structures, the play order may 
differ or playback may not be possible.
≥ CD-R, CD-RW : ISO9660 level 1 or 2 (except for extended formats), Joliet
This unit is compatible with multi-session.
This unit is not compatible with packet writing.
≥ DVD-R, DVD-R DL (except for AVCHD) : ISO9660 level 1 or 2 (except for 
extended formats), Joliet, UDF bridge (UDF 1.02/ISO9660)
This unit is not compatible with multi-session.
This unit is not compatible with packet writing.
MP3
File format MP3
Extension Files must have the extension “.mp3” or 
“.MP3”.
Compression 
rate 32 kbps to 320 kbps
Sampling rate 44.1 kHz/48 kHz
Reference ID3 tags: version 1, 2.2, 2.3, 2.4
(Only titles and the names of artists)
JPEG
File format JPEG
ExtensionFiles must have the extension “.jpg” or 
“.JPG”.
Picture 
resolution between 34
k34 and 8192 k8192 pixels
(sub sampling is 4:2:2 or 4:2:0)
Reference JPEG conforming DCF* is supported.
≥
MOTION JPEG and Progressive JPEG is 
not supported
* Design rule for Camera File system: unified standard  established by Japan Electronics and Information 
Technology Industries Association (JEITA). 
≥ DVD-RAM must conform to UDF 2.0.
≥ BD-RE must conform to UDF 2.5.
DivX
File format DivX
Extension Files must have the extension “.DIVX”, 
“.divx”, “.AVI” or “.avi”.
Picture 
resolution Up to 1920k1080 pixels
Reference ≥
DivX certified to play DivX video up to HD 
1080p, including premium content.
Video
– Number of streams: Up to 1
– Codec: DIV3, DIV4, DIVX, DX50, DIV6
– FPS (Frame Per Second): Up to 60 fps
Audio
– Number of streams: Up to 8
– Format: MP3, MPEG, Dolby Digital
– Multi channel: Dolby Digital is possible. 
MPEG multi is 2 ch conversion.
≥ GMC (Global Motion Compensation) is 
not supported.
≥ DVD-R and DVD-R DL must conform to UDF 1.02 without 
ISO9660 and UDF 1.5 with ISO9660.
≥ BD-R must conform to UDF 2.5.
Subtitles text file of DivX
File format Subtitles text file of DivX
MicroDVD, SubRip, or TMPlayer
Extension Files must have the extension “.SRT”, 
“.srt”, “.SUB”, “.sub”, “.TXT” or “.txt”.
Reference ≥
The DivX video file and subtitles text file 
are inside the same folder, and the file 
names are the same except for the file 
extensions.
≥ Depending on the methods used to 
create the file or the state of the 
recording, only parts of the subtitles may 
be displayed, or the subtitles may not be 
displayed at all.
AV C H D
File format AVCHD format (V1.0) used on High 
Definition Video Camera
(Panasonic and some others)
Codec MPEG-4 AVC/H.264
≥ Discs must conform to UDF 2.5.
MPEG2
File format SD-Video format
* used on Standard 
Definition Video Camera
(Panasonic and some others)
Codec MPEG2
* SD-Video Entertainment Video Profile
DMP-BDT300_VQT2J87_eng.book  40 ページ  ２０１０年１月２１日　木曜日　午後８時９分