Panasonic Dmp Bd85 Operating Instruction

							11VQT2H76
Connections & Settings
STEP 4 : Connecting to 
an AC power
≥This unit consumes a small amount of AC power (“Quick 
Start”: “Off”, less than 0.1 W) even when turned off. In the 
interest of power conservation, if you will not be using this 
unit for an extended period of time, it can be disconnected.
THE FOLLOWING APPLIES IN THE U.S.A. AND CANADA.This device complies with Part 15 of FCC Rules and RSS-Gen of IC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause interference, and (2) this device must 
accept any interference, including interference that may cause undesired 
operation of this device.
This transmitter must not be co-located or operated in conjunction with 
any other antenna or transmitter.
This product is restricted to indoor use due to its operation in the 5.15 to 
5.25 GHz frequency range.
FCC and IC require this product to be used indoors for the frequency 
range 5.15 to 5.25 GHz to reduce the potential for harmful interference to 
co-channel Mobile Satellite systems. High power radars are allocated as 
primary users of the 5.25 to 5.35 GHz and 5.65 to 5.85 GHz bands. These 
radar stations can cause interference with and/or damage this product.
The available scientific evidence does not show that any health problems 
are associated with using low power wireless devices. 
There is no proof, however, that these low power wireless devices are 
absolutely safe.
Low power Wireless devices emit low levels of radio frequency energy 
(RF) in the microwave range while being used. 
Whereas high levels of RF can produce health effects (by heating tissue), 
exposure to low-level RF that does not produce heating effects causes no 
known adverse health effects.
Many studies of low-level RF exposures have not found any biological 
effects. Some studies have suggested that some biological effects might 
occur, but such findings have not been confirmed by additional research. 
Wireless LAN adaptor (DY-WL10) has been tested and found to comply 
with FCC/IC radiation exposure limits set forth for an uncontrolled 
equipment and meets the FCC radio frequency (RF) Exposure Guidelines 
in Supplement C to OET65 and RSS-102 of the IC radio frequency (RF) 
Exposure rules. 
THE FOLLOWING APPLIES ONLY IN THE U.S.A.
FCC Note:
This equipment has been tested and found to comply with the limits for a 
Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against 
harmful interference in a residential installation. This equipment 
generates, uses and can radiate radio frequency energy and, if not 
installed and used in accordance with the instructions, may cause harmful 
interference to radio communications. 
However, there is no guarantee that interference will not occur in a 
particular installation. If this equipment does cause harmful interference to 
radio or television reception, which can be determined by turning the 
equipment off and on, the user is encouraged to try to correct the 
interference by one or more of the following measures:
≥ Reorient or relocate the receiving antenna.
≥ Increase the separation between the equipment and receiver.
≥ Connect the equipment into an outlet on a circuit different from that to 
which the receiver is connected.
≥ Consult the dealer or an experienced radio/TV technician for help.
FCC caution: To maintain compliance with FCC regulations, shielded 
interface cables must be used with this equipment. Operation with 
non-approved equipment or unshielded cables may result in interference 
to radio and TV reception. Any changes or modifications not approved by 
the party responsible for compliance could void the user’s authority to 
operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject 
to the following two conditions: 
(1) This device may not cause harmful interference, and 
(2) this device must accept any interference received, including 
interference that may cause undesired operation.
Responsible Party:
Panasonic Corporation of North America
One Panasonic Way
Secaucus, NJ 07094
Support Contact:
Panasonic Consumer Electronics Company
Telephone No.: 1-800-211-PANA (7262)
THE FOLLOWING APPLIES ONLY IN CANADA.This Class B digital apparatus complies with Canadian ICES-003.
Product Identification Marking is located on the bottom of unit.
The socket outlet shall be installed near the equipment and easily 
accessible. The mains plug of the power supply cord shall remain 
readily operable.
To completely disconnect this apparatus from the AC Mains, disconnect 
the power supply cord plug from AC receptacle.
AC power supply cord 
(included)
To a household AC outlet
DMP-BD85VQT2H76_eng.book  11 ページ  ２００９年１２月８日　火曜日　午後８時０分 
						

							12VQT2H76
STEP 5 : Setting
After connecting your new player for the 1st time and pressing 
the power button, a screen for the basic settings will appear.
PreparationTurn on the television and select the appropriate video 
input on the television.
1Press [ÍPOWER].
Setup screen appears.
If this unit is connected to a Panasonic TV (VIERA) 
supporting HDAVI Control 2 or later via an HDMI cable, 
then the setting information on the TV is acquired by this 
TV.
2Follow the on-screen instructions and 
make the settings with [ 3,4] and press 
[OK].
After completing “Easy Setting”, you can perform “Network 
Easy Setting”.
	≥ You can perform this setup anytime by selecting “Easy Setting” in the 
Setup menu. (>29)
≥ Initial setting is set to “2ch (Downmix) + 5.1ch”,  so you will need to select 
“7.1ch” if using the 7.1ch output.
After completing “Easy Setting”, you can continuously perform 
“Network Easy Setting”.
≥ Before you perform the wireless network settings on this 
unit, confirm the set up of your Wireless router (Access 
point) is done correctly on your PC.
1Select “Wired” or “Wireless” and press 
[OK].
2Follow the on-screen instructions and 
make the settings with [ 3,4,2,1] and 
press [OK].
For wireless LAN connection:
If you are using a Wireless router (Access point) that supports 
WPS, you can easily perform the settings by selecting “WPS 
(PUSH button method)”.
Otherwise, perform the settings by selecting “Search for 
access point” or “Manual setting” in “Other methods”.
≥ WPS (Wi-Fi Protected Setup) is a function that facilitates 
settings relating to the connection and security of wireless 
LAN devices. To see whether your Wireless router (Access 
point) supports WPS, check the Wireless router operating 
instructions.
Easy Setting
OKRETURN
Analog Audio  Output
Set unit’s analog audio output.
Select only “7.1ch” to enjoy audio from a
receiver through 7.1ch analog connections.
Otherwise, select “2ch (Downmix) + 5.1ch.” 
2ch (Downmix) + 5.1ch7.1ch
Network Easy Setting
OKRETURN
Network Easy Setting (Connection Check)
Wired
Wireless
A settings check for home network and Internet connections
is now being conducted.
Please select a connection mode first.
 
 Current setting  :  Wired
 
LAN cable connection:
 Connect a LAN cable to the unit and select “Wired.”
Wireless LAN connection:
 Insert a compatible Wireless LAN Adaptor to USB port 
 and select “Wireless.”
 Access point is necessary for Wireless LAN connection.
OKRETURN
Access Point Connection Setting
Select a connection method to use with an access point 
of Wireless LAN.
Please refer to the operating instructions of the access
point about connection methods.
WPS (PUSH button method)
Other methods
p
WPS (PIN code method)
Search for access point
Manual setting
DMP-BD85VQT2H76_eng.book  12 ページ  ２００９年１２月３日　木曜日　午後４時５７分 
						

							13VQT2H76
Connections & Settings
Access Point Connection Setting
Network Easy Setting (Connection Check)Network Easy Setting (Internet Connection Check)
	≥
Refer to the operating instructions of the hub or router.
≥ You can perform this setup anytime by selecting “Network Easy Setting” in 
the Setup menu. (
>29)
≥ You can redo these settings individually using “Network Settings”. (>29)
≥ If you experience problems after selecting “Wireless”, you should 
first confirm the setting of your Wireless router (Access point) 
connected to your home network using your PC.
≥ After performing network settings on this unit, the settings (encryption 
level, etc.) of the Wireless router (Access point) might change. When you 
have trouble getting online on your PC, perform the network settings on 
your PC in accordance with the settings of Wireless router (Access point).
When you experience 
problems with settings
DisplayCheck the following
A conflict with another 
device occurred. ≥
Please wait a few moments, 
and then try again.
A time out error occurred. ≥
Setting of the Wireless 
router (Access point) for 
MAC Address etc.
≥ The signal may be weak. 
Using the included USB 
extension cable, adjust the 
position of the Wireless LAN 
Adaptor.
≥ The SSID and the 
encryption key of the 
Wireless router (Access 
point).
≥ Please wait a few moments, 
and then try again.
An authentication error or a 
time out error occurred.
A device error occurred.
≥
Connection of Wireless LAN 
Adaptor
If there is no improvement in 
symptom, contact our 
Customer Service Center.
DisplayCheck the 
following
1. LAN cable connection or  
Connection to access point :Fail≥
Connection of 
the LAN 
cables ( >10)
2. IP address setting : Fail
3. Connection to gateway : Fail
OK
Access Point Connection Setting
Failed to connect to the access point.
A conflict with another device occurred.
Do you want to configure Access Point Connection
Setting again ?
Yes No
OK
Network Easy Setting (Connection Check)
YesNo
Complete.
1. LAN cable connection         
2. IP address setting
3. Connection to gateway
LAN cable is not connected.
Please check the connection.
Select “Yes” and press [OK] to check network
connection again. Select “No” and press [OK]
to finish Network Easy Setting.
: Fail
: Fail
: Fail
1. LAN cable connection or 
Connection to access point :Pass≥
Connection 
and settings 
of the hub 
and router
≥ Settings of 
“IP Address/
DNS 
Settings” 
(> 29)
2. IP address setting : Fail
3. Connection to gateway : Fail
1. LAN cable connection or
 
Connection to access point :Pass
2. IP address setting : Pass
3. Connection to gateway : Fail
DisplayCheck the following
Cannot find the server.
(Error code: B019) ≥
Settings of “IP Address/DNS 
Settings” ( >29)
Failed to connect to 
the server.
(Error code: B020) ≥
The server may be busy or the 
service may have been 
suspended. Please wait a few 
moments, and then try again.
≥ Settings of “Proxy Server 
Settings” ( >29) and the router
OK
Network Easy Setting (Internet Connection Check)Complete.
- Connection to the Internet       :   Fail(Error code: B019)
Failed the connection test.
Cannot find the server.(Error code: B019)
Please refer to the operating instructions for the cause
of the error and the solution for it.
Press [OK].
DMP-BD85VQT2H76_eng.book  13 ページ  ２００９年１２月８日　火曜日　午後８時０分 
						

							14VQT2H76
Occasionally, Panasonic may release updated firmware for 
this unit that may add or improve the way a feature operates. 
These updates are available free of charge.
This unit is capable of checking the firmware automatically 
when connected to the Internet via a broadband connection.
When a new firmware version is available, the following 
screen is displayed. 
DO NOT DISCONNECT the unit from the AC power or 
perform any operation while the update takes place.
After the firmware is installed, “FINISH” will be displayed on 
the unit’s display. Unit will restart and the following screen will 
be displayed.
	≥You can perform update anytime by selecting  “Firmware Update” in the 
Setup menu . (>29)
≥ If downloading on this unit fails or this unit is not connected to the 
Internet, then you can download the latest firmware from the 
following website and burn it to a CD-R to update the firmware.
http://panasonic.co.jp/pavc/global/cs
(This site is in English only.)
To show the firmware version on this unit. (
>29, “System 
Information”)
≥ Downloading will require several minutes. It may take longer or the 
Int
ernet may not be connected depending on the connection environment. ≥If you do not want to check for the latest firmware version, set “Automatic 
Update Check” to “Off”. (>29)
STEP 6 : 
Reprogramming the 
remote control
Change “Remote Control Code” ( >29) on the main unit and 
the remote control (the two must match) if you place other 
Panasonic products close together and it responds to this 
remote control.
You can operate the TV or amplifier/receiver using the unit’s 
remote control.
1For televisions
Input the code (>38) with the numbered 
buttons while pressing [ ÍTV POWER]. 
For amplifiers/receivers
Input the code (>38) with the numbered 
buttons while pressing 
[RECEIVER jVOL].
e.g., 0001: [0]  B [0] B [0] B [1] 
2Test by turning on the television or 
adjusting the volume of the amplifier/
receiver.
	≥ If your television or amplifier/receiver brand has more than one code 
listed, select the one that allows correct operation.
Firmware updates
Firmware Update
  Latest Online Version: x.xx
  Current Installed Version: x.xx
Do you want to start firmware update?
For the update information, please visit the
following website:
http://panasonic.net/support/
RETURNOK
Ye s No
The firmware was updated.Current Installed Version: x.xx
RETURNOK
For other Panasonic products
For TV or amplifier/receiver
VQT2H76~Body_eng.fm  14 ページ  ２００９年１２月１０日　木曜日　午後１時３１分 
						

							15VQT2H76
Connections & Settings
Playback
Playback
Inserting or removing a 
media
≥When inserting a media, ensure that it is facing the right 
way up.
≥ When indicator on this units display blinks, do not turn off 
the unit or remove the media. Such action may result in loss 
of the media’s contents.
≥ When removing the SD card, press on the center of the card 
and pull it straight out.
≥ If you connect a Panasonic product with a USB connection 
cable, setup screen may be displayed on connected 
equipment. For details, refer to the instructions for the 
connected equipment.
∫ To switch drives
Press [DRIVE SELECT] to select “BD/DVD/CD”, “SD card” 
or “USB device”.
≥If a media is inserted while the unit is stopped, the drive 
switches automatically depending on the inserted media.
FUNCTIONS menu
Major functions of this unit can be operated from the 
FUNCTIONS menu.
Press [ 3,4 ] to select the item and press [OK].
To exit the screen
Press [FUNCTION MENU].
	≥ Items to be displayed may vary with the media.
≥ If FUNCTIONS screen is not displayed, press [FUNCTION MENU].
SD CARD
PlaybackPlay back the contents.
To p  M e n u(> 16)
Menu(>16)
Viewing Picture(>20)
Viewing Video(>16)
Listening Music(>21)
NetworkDisplays the Home screen of 
the VIERA CAST ( >23)
BD/DVD/CD
Switches to each drive.SD Card
USB device
Other 
Functions Playlists
You can play playlists created 
on DVD-VR.
Setup
(> 26)
Card 
Management
(> 18)
Playback
Top Menu
USB device
SD Card
Blu-ray Disc Player
FUNCTIONS
BD-Video
Other Functions
Network
OKRETURN
VQT2H76~Body_eng.fm  15 ページ  ２００９年１２月９日　水曜日　午後７時３３分 
						

							16VQT2H76
Playing video contents
Preparation
Turn on the television and select the appropriate video input 
on the television.
1Press [ÍPOWER] to turn on the unit.
2Insert the media.
Play starts.
≥If the menu is displayed, press [ 3,4, 2,1 ] to select 
the item and press [OK].
≥ If play does not start, press [ 1](PLAY).
∫ To show menus
You can show Top Menu, Direc t Navigator or Pop-up Menu.
Press [TOP MENU/DIRECT NAVIGATOR] or [POP-UP 
MENU].
≥ Press [ 3,4 ,2, 1] to select the item and press [OK].
≥ Pop-up menu also appears by  pressing [SUB MENU] and 
selecting “Pop-up Menu”.
∫ To show the status messages
While playing, press [STATUS].
The status messages give you information about what is 
currently being played. Each time you press [STATUS], the 
information displayed will change.
	≥DISCS CONTINUE TO ROTATE WHILE MENUS ARE DISPLAYED. 
Press [∫] when you finish to preserve the unit’s motor and your television 
screen.
≥ Depending on media and contents, the display may change or may not 
appear.
≥ DivX: Successive play is not possible.
≥ It is not possible to playback AVCHD and MPEG2 video which have 　
been dragged and dropped, copied and pasted to the media.
These functions may not work depending on the media and 
contents.
Press [ ∫].
The stopped position is memorized.
Resume play function
Press [ 1] (PLAY) to restart from this position.
≥ The position is cleared if the  tray is opened or you press [∫] 
several times to display “STOP” on unit’s display.
≥ On BD-Video discs including BD-J ( >39), the resume 
play function does not work.
Press [ ;].
≥ Press [ ;] again or [ 1] (PLAY) to restart play. 
Search
While playing, press [ 6] or [ 5].
≥ Music and MP3: The speed is fixed to a single step.
Slow-motion
While paused, press [ 6] or [ 5].
≥ BD-Video and AVCHD: Forward direction [ 5] only.
The speed increases up to 5 steps.
≥ Press [ 1] (PLAY) to revert to normal playback speed.
While playing or paused, press [ :] or [9 ].
Skip to the title, chapter or track you want to play.
≥ Each press increases the number of skips.
While paused, press [ 2] (2; ) or [1] (;1 ).
≥ Press and hold to change in succession forward or 
backward.
≥ Press [ 1] (PLAY) to revert to normal playback speed.
≥ BD-Video and AVCHD: Forward direction [ 1] (;1 ) only.
Press [AUDIO].
You can change the audio channel number or soundtrack 
language ( >24), etc.BDDVDCDSDUSB
1
PlayBD-Video T1     C1     0:05.140:20.52
e.g.BD-Video
To t a l  t i m e
Elapsed time in the title
Current position
T: Title, C: Chapter, PL: Playlist
Other operations during play 
Stop
Pause
Search/Slow-motion
Skip
Frame-by-frame
Changing audio
VQT2H76~Body_eng.fm  16 ページ  ２００９年１２月８日　火曜日　午後８時８分 
						

							17VQT2H76
Playback
1Press [SUB MENU].
2Select an item, then press [OK].
≥Depending on the played contents if you perform “Screen 
Aspect”, there may be not effect.
≥ When “TV Aspect” ( >28) is set to “4:3 Pan & Scan” or “4:3 
Letterbox”, the “Zoom” effect in “Screen Aspect” is disabled. 
	≥ Depending on the media and contents, displayed items are different.
Useful functions
While Direct Navigator screen is displayed
PropertiesTo display the titles properties (recording 
date, etc.)
View 
ChaptersTo select the chapter
To  p i c t u r ePlaying still pictures (> 20)
Select 
FolderTo switch to another folder
While playing
Screen 
AspectWhen black bars are shown at the top, 
bottom, left, and right sides of the screen, you 
can enlarge the image to fill the screen.
Top MenuTo display Top Menu.
Pop-up 
MenuTo display Pop-up Menu.
MenuTo display Menu.
DMP-BD85VQT2H76_eng.book  17 ページ  ２００９年１１月３０日　月曜日　午後５時３２分 
						

							18VQT2H76
What is BONUSVIEW?
BONUSVIEW allows you to enjoy functions such as 
picture-in-picture or secondary audio etc.
What is BD-Live?
In addition to the BONUSVIEW function, BD-Live allows you 
to enjoy more functions such  as subtitles, exclusive images 
and online games by connecting th is unit to the Internet.
≥ The usable functions and the operating method may vary 
with each disc, please refer to the instructions on the disc 
and/or visit their website.
To turn on/off secondary video
Press [PIP].
To turn on/off secondary audio
[DISPLAY] >  select “Disc” > [1] >  select 
“Signal Type” > [OK] >  set “Soundtrack” in 
“Secondary Video” to
 “On” or “Off”
	≥ During search/slow-motion or frame-by-frame, only the primary video is 
displayed.
≥ When “BD-Video Secondary Audio” in “Digital Audio Output” is set to “Off”, 
secondary audio will not be played (
>27).
Some BD-Live content available on the Blu-ray discs may 
require an Internet account to  be created in order to access 
the BD-Live content. Follow the screen display or instruction 
manual of the disc for information on acquiring an account.
1Connect to the network. (>10)
2Insert an SD card (with 1 GB or more free space).
SD card is used as the local storage ( >39).
3Insert the disc.
∫Deleting data/Formatting SD cards
1 Insert an SD card.
2 Press [FUNCTION MENU].
3 Press [ 3,4 ] to select “Other Functions” and press [OK].
4 Press [ 3,4 ] to select “Card Management” and press 
[OK].
5 Press [ 3,4 ] to select “BD-Video Data Erase” or “Format 
SD Card” and press [OK].
6 Press [ 2,1 ] to select “Yes” and press [OK].
7 Press [ 2,1 ] to select “Start” and press [OK].
	≥ To use the above functions, it is recommended that you format the card on\
 
this unit. If the SD card you use is formatted, all data on the card will be 
erased. It cannot be recovered.
≥ “BD-Live Internet Access” may need to be changed for certain discs 
(
>26) .
≥ When discs supporting BD-Live are played back, the player or disc IDs 
may be sent to the content provider via the Internet.
Enjoying BD-Live or 
BONUSVIEW in BD-Video
Playing picture-in-picture
Secondary video
Primary video
Enjoying BD-Live discs with 
Internet
Card Management No. of Files    6
Free space    300 MB
SD card
Format this SD Card.
BD-Video Data Erase
Format SD Card
OKRETURN
DMP-BD85VQT2H76_eng.book  18 ページ  ２００９年１２月３日　木曜日　午後４時５７分 
						

							19VQT2H76
Playback
ABOUT DIVX VIDEO:
DivX® is a digital video format created by DivX, Inc. This is an 
official DivX Certified device that plays DivX video. Visit 
www.divx.com for more information and software tools to 
convert your files into DivX video.
ABOUT DIVX VIDEO-ON-DEMAND:
This DivX Certified
® device must be registered in order to play 
DivX Video-on-Demand (VOD) content. 
To generate the registration code, locate the DivX VOD 
section in the device setup menu. 
Go to vod.divx.com with this code to complete the registration 
process and learn more about DivX VOD.
≥ It is not possible to playback DivX VOD content recorded on 
the USB device.
Display the unit’s registration code.
(> 29, “DivX Registration” in “Others”)
≥ After playing DivX VOD content for first time, the registration 
code is not displayed.
≥ If you purchase DivX VOD content using a registration code 
different from this unit’s code, you will not be able to play 
this content. (“Authorization Error” is displayed.)
Cancel the unit’s registration.
(> 29, “DivX Registration” in “Others”)
Press [ 2,1] to select “Yes” in “DivX Registration”.
Use the deregistration code to cancel the registration in 
www.divx.com.
Regarding DivX VOD content that can only be played a 
set number of times
Some DivX VOD content can only be played a set number of 
times. When you play this content, the remaining number of 
plays is displayed. You cannot play this content when the 
number of remaining plays is zero. (“Rental Expired.” is 
displayed.)
≥ The remaining number of plays decreases each time a 
program is played. However, when playing from the point 
where play was previously  stopped, the remaining number 
of plays does not decrease due to the resume play function.
∫ Displaying subtitles text
You can display subtitles text on the DivX video disc with this 
unit. This function has no relation to the subtitles specified in 
DivX standard specifications  and has no clear standard.
The 
operation might be different or  it may not operate properly 
depending on the way the file was made or the state of this 
unit (playing, stopped, etc.).
Set “Subtitle” in “Disc” ( >24)
	≥DivX video files that do not display “Text” do not contain subtitles text.
≥ If the subtitles text are not displayed correctly, try changing the language 
settings. (
>26)
Regarding DivX
DivX Registration
The registration code is necessary to
register this unit to play protected
DivX videos.
Registration Code: XXXXXXXXXX
Please register at www.divx.com/vod/
10 alphanumeric 
characters
VQT2H76~Body_eng.fm  19 ページ  ２００９年１２月９日　水曜日　午後７時３３分 
						

							20VQT2H76
Playing still pictures
(BD-RE, DVD-RAM/-R/-R DL, CD-R/RW, SD Card, 
USB device)
1Insert a disc, SD card or USB device.
If the menu is displayed, press [3,4] to select the item 
and press [OK].
2BD-RE, DVD-RAM
Press [ 3,4 ,2, 1] to select the album 
and press [OK]. 
3Press [ 3,4 ,2, 1] to select the still 
picture and press [OK].
Press [ 2,1 ] to display the previous or next still picture.
To exit the screen
Press [TOP MENU/DIRECT NAVIGATOR].
∫ To show the picture properties
While playing, press [STATUS] twice.
To exit the screen
Press [STATUS].
1Press [SUB MENU].
2Select an item, then press [OK].
	≥Depending on the media and contents, displayed items are different.
≥ When a still picture with large number of pixels is played, the display 
interval may become longer. Even if the setting is changed, the display 
interval may not become shorter.
≥ When both the music CD and the USB device with MP3 recorded is 
inserted to this unit, the music CD has a priority to be played back as 
Background Music.
BDDVDCDSDUSB
RG
 Total 8
106_DVD
 Total 132006  9  12
VideoPicture
Press [OK] to go to Picture View.
Previous Next
Slideshow
Video Picture Page  02/02BY
DIRECT NAVIGATORAlbum ViewDVD-RAM(VR)
SUB
MENUOKRETURN
DIRECT NAVIGATORDVD-RAM(VR)Picture View
SUB
MENU PlayRETURN
Video
Picture2006  9  12
Page  001/001
0001
0005
0009 0006 0007 0008 0002 0003 0004
                                    
Photo     11/12/2007            Total        3/9
e.g. JPEG on DVD-RAM Shooting date
Useful functions
While “Album View” or “Picture View” screen is displayed
Start 
SlideshowYou can display still pictures one by one at a 
constant interval.
Slideshow 
Settings
Display Interval
Change the display interval.
Transition Effect
Set display method.
Repeat Play
Repeat slideshow.
Soundtrack
The MP3 that is recorded on the USB device 
or the music CD can be played back as 
Background Music during the slideshow.
Soundtrack Folder
A folder to playback can be selected when a 
USB device with MP3 recorded is connected 
to this unit.
Press [3,4, 2,1 ] to select “Set” and 
press [OK].
Select Root 
folderTo switch to another higher folder
≥ Only if there is a multiple number of higher 
folders recognizable
Select 
FolderTo select the still pictures in another folder
To  Vi d e oPlaying video contents ( >16)
To album 
viewTo display album view.
While playing (except for slideshow)
Rotate RightRotate the still picture.Rotate Left
Zoom out
Reduce the still picture
≥ This function is only available for 
small-sized still pictures.
Zoom inCancel “Zoom out”
DMP-BD85VQT2H76_eng.book  20 ページ  ２００９年１２月５日　土曜日　午後６時２１分