Panasonic Dmc Fx35 Operating Instructions Manual

							71VQT1P09
Advanced (Playback)
∫Operations performed during slide showThe cursor displayed during playback is the same as 3/4/2/1.The menu screen is restored when [‚] is pressed.
∫Changing the slide show settingsYou can change the settings for slide show playback by selecting 
[EFFECT] or [SETUP] on the slide show menu screen.
[EFFECT]This allows you to select the screen effects or music effects when 
switching from one picture to the next.
[NATURAL], [SLOW], [SWING], [URBAN], [OFF], [AUTO]
When [URBAN] has been selected, the picture may appear in black and white as a screen effect.[AUTO] can be used only when [CATEGORY SELECTION] has been selected. The pictures are 
played back with the recommended effects in each category.
[SETUP][DURATION] or [REPEAT] can be set.
[DURATION] can be set only when [OFF] has been selected as the [EFFECT] setting.[AUDIO] will be displayed only when the [EFFECT] is set to [OFF]. Audio will be played along 
with the still picture with audio by setting the [AUDIO] to [ON].
Note
Motion pictures cannot be played back as a slide show.It is not possible to add new music effects.
Press 3 to select [START] and then press [MENU/
SET].
Press 4 to finish the slide show.
Normal playback resumes after the slide show finishes.
APlay/Pause
BStop
CBack to previous picture
¢
DAhead to next picture¢
¢These operations can be performed only in the pause mode.
EReduce volume level
FIncrease volume level
ItemSettings
[DURATION]1SEC./2SEC./3SEC./5SEC.
[REPEAT]ON/OFF
[MUSIC]/[AUDIO]ON/OFF
6
7
A
B
CD
FE
DMC-FX35P_mst.book  71 ページ  ２００８年１月１５日　火曜日　午前１０時３６分 
						

							VQT1P0972
Advanced (Playback)
[PLAYBACK] mode: ¸
Selecting Pictures and Playing them Back 
([CATEGORY PLAY]/[FAVORITE PLAY])
This mode allows you to search images by scene mode or other categories (such as 
[PORTRAIT], [SCENERY] or [NIGHT SCENERY]) and sort the pictures into each of the 
categories. You can then play back the pictures in each category.
Perform steps 1 and 2 on page 70.
Press 3/4 to select [CATEGORY PLAY], and then press [MENU/SET].
Press 3/4/2/1 to select the category and then 
press [MENU/SET] to set.
If a picture is found in a category, the category icon turns blue.It may take time to search the picture files if there are a lot on the 
card or the built-in memory.
If you press [‚] while searching, the searching will stop halfway.Pictures are sorted into the categories shown below.
¢The travel dates of images in the clipboard folder are not categorized.
Still pictures created from a motion picture cannot be played back from the motion 
pictures category in category playback.
[CATEGORY PLAY]
[CATEGORY]Recording information 
e.g. scene modes[CATEGORY]Recording information 
e.g. scene modes
* [PORTRAIT], 
[i-PORTRAIT], 
[SOFT SKIN], 
[SELF PORTRAIT], 
[NIGHT PORTRAIT], 
[i-NIGHT PORTRAIT], 
[BABY1]/[BABY2][SPORTS], [PARTY], 
[CANDLE LIGHT], 
[FIREWORKS], [BEACH], 
[SNOW], 
[AERIAL PHOTO]
, [SCENERY], 
[i-SCENERY], [SUNSET], 
[AERIAL PHOTO]
Î [BABY1]/[BABY2]
í [PET]
1 [FOOD]
. [NIGHT PORTRAIT], 
[i-NIGHT PORTRAIT], 
[NIGHT SCENERY], 
[i-NIGHT SCENERY], 
[STARRY SKY]
< [UNDERWATER]
[TRAVEL DATE]¢
Í [MOTION PICTURE]
1
2
3
DMC-FX35P_mst.book  72 ページ  ２００８年１月１５日　火曜日　午前１０時３６分 
						

							73VQT1P09
Advanced (Playback)
You can play back the pictures you have set as [FAVORITE] (P83) (Only when [FAVORITE] is set 
to [ON] and there are pictures which have been set to [FAVORITE]).
Perform steps 1 and 2 on page 70.
Press 3/4 to select [FAVORITE PLAY], and then press [MENU/SET].
Note
You can use only [ROTATE], [ROTATE DISP.], [DPOF PRINT], [PROTECT] or  [AUDIO DUB.] in 
the [PLAYBACK] menu.
[FAVORITE PLAY]
1
2
DMC-FX35P_mst.book  73 ページ  ２００８年１月１５日　火曜日　午前１０時３６分 
						

							VQT1P0974
Advanced (Playback)
[PLAYBACK] mode: ¸
Playing Back Motion Pictures/Pictures with Audio
Press 2/1 to select a picture with a motion picture 
icon (such as [ù]), and then press 3 to play back.
AThe motion picture recording time
BMotion picture icon
CMotion picture playback icon
After playback starts, the elapsed playback time is displayed on the 
upper right of the screen.
For example, 8 minutes and 30 seconds is displayed as [8m30s].
∫Operations performed during motion picture playbackThe cursor displayed during playback is the same as 3/4/2/1.
APlay/Pause
BStop
CFast rewind, Frame-by-frame rewind
¢
DFast forward, Frame-by-frame forward¢
¢These operations can be performed only in the pause mode.
EReduce volume level
FIncrease volume level
Note
Sound can be heard through the speaker. Refer to [VOLUME] (P21) for information about how 
to adjust the volume in the [SETUP] menu.
The file format that can be played back with this camera is QuickTime Motion JPEG.Please note that the bundled software includes QuickTime to play back motion picture files 
created with the camera on the PC.
Some QuickTime Motion JPEG files recorded by a PC or other equipment may not play back on 
the camera.
If you play back motion pictures that have been recorded with other equipment, the picture 
quality may deteriorate or the pictures may not play back.
When using a high capacity card, it is possible that fast rewinding may be slower than usual.
Motion pictures
Pictures with audio
Press 2/1 to select a picture with the audio icon [ ] 
and then press 3 to play back.
AAudio iconRefer to [AUDIO REC.] (P66) and [AUDIO DUB.] (P86) for information 
about how to create still pictures with audio.
ABC
A
B
CD
FE
A
DMC-FX35P_mst.book  74 ページ  ２００８年１月１５日　火曜日　午前１０時３６分 
						

							75VQT1P09
Advanced (Playback)
[PLAYBACK] mode: ¸
Creating still pictures from a motion picture
You can create a single still picture (with 1 screen or 9 screens) from a recorded motion picture. 
This is effective in moving scenes when you want to look carefully at the movement of a 
sportsperson etc.
Press 3 to pause motion picture playback.
To save the displayed image as 1 picture > go to step 3To save the motion picture as 1 picture with 9 screens > go to 
step 2
Press [MENU/SET] to display the 9 screens 
playback screen.
A: 30  frames: Display image every 1/30  second as picture
To advance frame-by-frame
3/4: Advance every 3 frames
2/1: Advance every 1 frames
Change the number of frame rate per second
Turn the zoom lever toward  [L] (W)
To end 9 screen display
Press [MENU/SET]
Press the shutter button.
Press 3 to select [YES] and then press 
[MENU/SET].
[QUALITY] is fixed to [›].
Note
You may not be able to save still pictures from a motion picture taken on other equipment.
QualityFrame rate per second
÷/ù/ý/ÿ 30>15>10>5
ü 15>5
ö/ø/þ 10>5
Picture size
Item1picture9pictures
÷/ö 0.3M 2M
ù/ø 0.3M 1M
ý/ü/ÿ/þ 2M 2M
1
A
2
3
4
DMC-FX35P_mst.book  75 ページ  ２００８年１月１５日　火曜日　午前１０時３６分 
						

							VQT1P0976
Advanced (Playback)
[PLAYBACK] mode: ¸
Using the [PLAYBACK] mode menu
You can use various functions in playback mode to rotate pictures, set protection for them etc.With [TEXT STAMP], [RESIZE], [TRIMMING] or [ASPECT CONV.], a new edited picture is 
created. A new picture cannot be created if there is no free space on the built-in memory or the 
card so we recommend checking that there is free space and then editing the picture.
You can display pictures by recording date.
Note
The recording date of the picture selected in the playback screen becomes the date selected 
when the calendar screen is first displayed.
If there are multiple pictures with the same recording date, the first picture recorded on that day 
is displayed.
You can display the calendar between January 2000 and December 2099.If the date is not set in the camera, the recording date is set as January 1st, 2008.If you take pictures after setting the travel destination in [WORLD TIME], the pictures are 
displayed by the dates at the travel destination in calendar playback.
 [CALENDAR]
Select [CALENDAR] on the [PLAYBACK] mode menu. (P18)
You can also rotate the zoom lever several times towards [L] (W) to display the 
calendar screen. (P32)
Press 3/4/2/1 to select the date to be played 
back.
3/4: Select the month
2/1: Select the date

If there were no pictures recorded during a month, the month is 
not displayed.
Press [MENU/SET] to display the pictures that were 
recorded on the selected date.
Press [‚] to return to the calendar screen.
Press 3/4/2/1 to select a picture and then press [MENU/SET].
The picture that was selected will appear.
CAL
1
2
3
4
DMC-FX35P_mst.book  76 ページ  ２００８年１月１５日　火曜日　午前１０時３６分 
						

							77VQT1P09
Advanced (Playback)
You can add text (comments) to pictures. After text has been registered, it can be included in 
prints using [TEXT STAMP] (P78). (Only alphabetic characters and symbols can be entered.)
Select [TITLE EDIT] on the [PLAYBACK] mode menu. (P18)
Press 3/4 to select [SINGLE] or [MULTI] and then 
press [MENU/SET].
Press 3/4/2/1 to select text and then press 
[MENU/SET] to register.
Press [DISPLAY] to switch text between [A] (capitals), [a] (small 
case) and [&/1] (special characters and numbers).
The cursor at the entry position can be moved to the left with 
[L], and to the right with [Z].
To enter a blank, move the cursor to [SPACE] or to delete an entered character, move 
the cursor to [DELETE], and press [MENU/SET].
To stop editing at any time during text entry, press [‚].A maximum of 30 characters can be entered.
Press 3/4/2/1 to move the cursor to [EXIT] and then press [MENU/
SET] to end text input.
Press [‚] to return to the menu screen.
¢
¢The menu screen is automatically restored when [MULTI] is selected.Press [MENU/SET] to close the menu.
∫Delete the title (for [SINGLE] only)1In step 4 when [SINGLE] (P77) is selected, delete all the texts, select [EXIT], and 
press [MENU/SET].
2Press [‚].3Press [MENU/SET] to close the menu.
 [TITLE EDIT]
Select the picture, and then 
press [MENU/SET] to set.
[’] A is displayed for pictures that 
have already been recorded with text 
in [BABY1]/[BABY2] or [PET] name 
settings in scene mode or [TITLE 
EDIT].
[MULTI] setting
Press [DISPLAY] to set (repeat), 
and then press [MENU/SET] to set.[SINGLE] [MULTI]
Press 2/1 to 
select the picture.Press 3/4/2/1 to 
select the pictures.

The setting is canceled when [DISPLAY] is pressed again.Titles cannot be changed or deleted in [MULTI].
1
2
3
A
4
5
6
DMC-FX35P_mst.book  77 ページ  ２００８年１月１５日　火曜日　午前１０時３６分 
						

							VQT1P0978
Advanced (Playback)
Note
Text can be scrolled if all of the registered text does not fit on the screen.The name setting of [BABY1]/[BABY2] or [PET] in scene mode can also be registered by using 
the operation in steps 4 and following.The name setting of [BABY1]/[BABY2] or [PET] in scene mode and [TITLE EDIT] cannot be 
registered at the same time.
You can print out texts (comments) using the “PHOTOfunSTUDIO-viewer-” bundled software on 
the CD-ROM (supplied).
You can set up to 50 pictures at one time with [MULTI].You cannot use titles edit for pictures taken with other equipment.
You can stamp the recording date/time, age, travel date or title onto the recorded pictures.
It is suitable for regular size printing. (Pictures with a picture size larger than [ ] will be resized 
when stamping the date etc. on them.)
Select [TEXT STAMP] on the [PLAYBACK] mode menu. (P18)
Press 3/4 to select [SINGLE] or [MULTI] and then 
press [MENU/SET].
Press 3/4/2/1 to select [SHOOTING DATE], [AGE], [TRAVEL DATE] 
or [TITLE] and then press [MENU/SET] to set each item.
[SHOOTING DATE]
[AGE] (P48)
If this is set to [ON], [AGE] is stamped on the pictures.
[TRAVEL DATE]
If this is set to [ON], [TRAVEL DATE] is stamped on the pictures.
[TITLE]
Text is printed together with the image for pictures that have already been recorded 
with text in [BABY1]/[BABY2] or [PET] name settings in scene mode or [TITLE 
EDIT].
 [TEXT STAMP]
Select the picture, and then 
press [MENU/SET] to set.
[‘] A appears on screen if the 
picture is stamped with text.
[MULTI] setting
Press [DISPLAY] to set (repeat), 
and then press [MENU/SET] to set.

The setting is canceled when 
[DISPLAY] is pressed again.
[SINGLE] [MULTI]
Press 2/1 to 
select the picture.Press 3/4/2/1 to 
select the pictures.
[W/OTIME]: Stamp the year, month and date.
[WITHTIME]: Stamp the year, month, day, hour and minutes.
1
2
3
A
4
DMC-FX35P_mst.book  78 ページ  ２００８年１月１５日　火曜日　午前１０時３６分 
						

							79VQT1P09
Advanced (Playback)
Press [MENU/SET].
If you set [TEXT STAMP] for a picture with a picture size larger than [ ], the picture 
size will become smaller as shown below.
The picture becomes slightly rougher.
Press 3 to select [YES] and then press [MENU/
SET].
The message [SAVE NEW PICTURES?] appears if the picture 
was recorded with a picture size [ ] or less.
Press [‚] to return to the menu screen.¢
¢The menu screen is automatically restored when [MULTI] is selected.Press [MENU/SET] to close the menu.
Note
When you print pictures stamped with text, the date will be printed over the stamped text if you 
specify printing of the date at the photo shop or on the printer.
You can set up to 50 pictures at one time in [MULTI].Depending on the printer being used, some characters may be cut at printing. Check before 
printing.
When text is stamped onto the [ ] pictures, it is difficult to read it.Text and dates cannot be stamped on the pictures taken with other equipment.
We recommend resizing to [ ] if you want to attach a picture to an e-mail or use it on a 
website. (Pictures set to the minimum number of pixels for [ASPECT RATIO] cannot be further 
reduced in size.)
Select [RESIZE] on the [PLAYBACK] mode menu. (P18)
Aspect ratio settingPicture size
X
 //> 
Y // > 
W // > 
Q
[RESIZE] Reducing the picture size (number of pixels)
Press 3/4 to select [SINGLE] or [MULTI] and then 
press [MENU/SET].
Select the picture and size.
[SINGLE] setting
1Press 2/1 to select the picture, 
and then press [MENU/SET].
2Press 2/1 to select the size¢, and 
then press [MENU/SET].
¢Only the sizes to which the pictures can 
be resized is displayed.
[SINGLE]
5
6
7
1
2
3
DMC-FX35P_mst.book  79 ページ  ２００８年１月１５日　火曜日　午前１０時３６分 
						

							VQT1P0980
Advanced (Playback)
Press 3 to select [YES] and then press [MENU/
SET].
Press [‚] to return to the menu screen.
¢
¢The menu screen is automatically restored when [MULTI] is 
selected.
Press [MENU/SET] to close the menu.
Note
You can set up to 50 pictures at one time in [MULTI].The picture quality of the resized picture will deteriorate.It may not be possible to resize pictures recorded with other equipment.
You can enlarge and then clip the important part of the recorded picture.
Select [TRIMMING] on the [PLAYBACK] mode menu. (P18)
Press [MENU/SET].
[MULTI] setting1Press 3/4 to select the size, and 
then press [MENU/SET].

When [DISPLAY] is pressed, an 
explanation of resizing is displayed.
2Press 3/4/2/1 to select the 
picture, and then press [DISPLAY].

Repeat this step for each picture, and 
press [MENU/SET] to set.
[MULTI]
 [TRIMMING]
Press 2/1 to select the picture, and then press 
[MENU/SET].
Use the zoom lever and press 
3/4/2/1 to select the parts 
to be trimmed.
Zoom lever (T): Enlargement
Zoom lever (W): Reduction
3/4/2/1: MoveReduction Enlargement
()
Move the position
()
4
5
1
2
3
4
DMC-FX35P_mst.book  80 ページ  ２００８年１月１５日　火曜日　午前１０時３６分