Panasonic Dmc Fx35 Operating Instructions Manual

							101VQT1P09
Others
Message Display
Confirmation messages or error messages will be displayed on the screen in some cases.
The major messages are described below as examples.
[THIS MEMORY CARD IS LOCKED]
>The Write-Protect switch on the SD Memory Card and the SDHC Memory Card are 
moved to [LOCK]. Move the switch back to unlock it. (P15)
[NO VALID PICTURE TO PLAY]
>Record a picture or insert a card with a recorded picture and then play it.
[THIS PICTURE IS PROTECTED]
>Delete the picture after canceling the protect setting. (P85)
[THIS PICTURE CANNOT BE DELETED]/[SOME PICTURES CANNOT BE DELETED]

Pictures not based on the DCF standard cannot be deleted.
>If you want to delete some pictures, format the card after saving necessary data on a PC 
etc. (P24)
[NO ADDITIONAL SELECTIONS CAN BE MADE]

The number of pictures, which can be set at one time when [MULTI] has been selected for 
[DELETE MULTI] (P34), [FAVORITE] (P83), [TITLE EDIT] (P77), [TEXT STAMP] (P78) or 
[RESIZE] (P79) has been exceeded.
>Reduce the number of pictures set, and then repeat the operation.
More than 999 favorites have been set.
[CANNOT BE SET ON THIS PICTURE]

[TITLE EDIT], [TEXT STAMP] or [DPOF PRINT] cannot be set for pictures not based on the 
DCF standard.
[NOT ENOUGH SPACE ON BUILT-IN MEMORY]/[NOT ENOUGH MEMORY ON THE 
CARD]

There is no space left on the built-in memory or the card.–When you copy pictures from the built-in memory to the card (batch copy), the pictures are 
copied until the capacity of the card becomes full.
[SOME PICTURES CANNOT BE COPIED]/[COPY COULD NOT BE COMPLETED] 

The following pictures cannot be copied.–When a picture with the same name as the picture to be copied exists in the copy 
destination. (Only when copying from a card to the built-in memory.)
–Files not based on the DCF standard.Moreover, pictures recorded or edited by other equipment may not be copied.
[BUILT-IN MEMORY ERROR FORMAT BUILT-IN MEMORY?]

This message will be displayed when you formatted the built-in memory on a PC.
>Format the built-in memory on the camera again. (P24) The data on the built-in memory 
will be deleted.
[MEMORY CARD ERROR FORMAT THIS CARD?]

This card has a format which is not recognized by the camera.
>Format the card again with the camera after saving necessary data on a PC etc. (P24)
DMC-FX35P_mst.book  101 ページ  ２００８年１月１５日　火曜日　午前１０時３６分 
						

							VQT1P09102
Others
[PLEASE TURN CAMERA OFF AND THEN ON AGAIN]

This message appears when the camera is not operating properly.
>Turn the camera off and on. If the message persists, contact the dealer or your nearest 
Service Center.
[MEMORY CARD PARAMETER ERROR]
>Use a card compatible with this unit. (P15)You can only use an SDHC Memory Card if using cards with 4 GB or more capacity.
[MEMORY CARD ERROR PLEASE CHECK THE CARD]

An error has occurred accessing the card.
>Insert the card again.
[READ ERROR PLEASE CHECK THE CARD]

An error has occurred reading the data.
>Insert the card again.
[WRITE ERROR PLEASE CHECK THE CARD]

An error has occurred writing the data.
>Turn the camera off and remove the card. Insert the card again and turn the camera on. 
Make sure the camera is turned off before removing or inserting the card to avoid damage.
[MOTION RECORDING WAS CANCELLED DUE TO THE LIMITATION OF THE 
WRITING SPEED OF THE CARD]

When you set the picture quality to [÷], [ý], [ü] or [ÿ], we recommend using a 
high-speed card with “10MB/s” or greater displayed on the package.
Depending on the type of SD Memory Card or SDHC Memory Card, motion picture recording 
may stop in the middle.
[A FOLDER CANNOT BE CREATED]

A folder cannot be created because there are no remaining folder numbers that can be used. 
(P89)
>Format the card after saving necessary data on a PC etc. (P24) If you execute 
[NO.RESET] in the [SETUP] menu after formatting, the folder number is reset to 100. 
(P22)
[PICTURE IS DISPLAYED FOR 4:3 TV]/[PICTURE IS DISPLAYED FOR 16:9 TV]

The AV cable is connected to the camera.
>Press [MENU/SET] if you want to delete this message at once.
>Select [TV ASPECT] in the [SETUP] menu if you want to change the TV aspect. (P23)
This message also appears when the USB connection cable is connected to the camera only.
In this case, connect the other end of the USB connection cable to a PC or a printer. (P88, 90)
[PRINTER BUSY]/[PLEASE CHECK THE PRINTER]

The printer cannot print.
>Check the printer.
DMC-FX35P_mst.book  102 ページ  ２００８年１月１５日　火曜日　午前１０時３６分 
						

							103VQT1P09
Others
Functions that cannot be set or will not work under 
some conditions
Due to the camera’s specifications, it may not be possible to set some of the functions or some 
functions may not work in some of the conditions under which the camera is used.
The table below lists these functions and the corresponding conditions.
For the functions which cannot be set or will not work in the Intelligent auto mode, refer to 
“Settings in Intelligent auto mode” (P28).
For the functions which cannot be set or will not work in the clipboard mode, refer to “Settings 
During Clipboard” (P69).
Functions that cannot be set 
or will not workMain conditions in which the functions cannot be set or will not 
work
[AUTO POWER LCD]/
[HIGH ANGLE] (P20)( mode
[POWER SAVE] (P21)When using the AC adaptorWhen connecting to a PC or a printerWhen recording or playing back motion picturesDuring a slide show[AUTO DEMO]
[AUTO LCD OFF] (P21)When using the AC adaptorWhile the menu screen is displayedWhile the self-timer is setWhile recording motion picturesWhen connecting to a PC or a printer
[AUTO REVIEW] (P22)$ mode
Extended Optical Zoom 
(P30)9 and ô in [SCENE MODE]$ mode
[DIGITAL ZOOM] (P30)-, :, ;, í, 9 and ô in [SCENE MODE]When Intelligent ISO is set
[HISTOGRAM] (P37)$ modeDuring multi playbackDuring playback zoom[CALENDAR]
[FLASH] (P38)When auto bracket has been setWhen the burst mode is set,, /, ï, ô, 5, 4 and 7 in [SCENE MODE]$ mode
[SELFTIMER] (P42)ô and < in [SCENE MODE]$ mode
[EXPOSURE] (P43)5 in [SCENE MODE]
[AUTO BRACKET] (P44)ô and 5 in [SCENE MODE]$ mode
[PICTURE SIZE] (P57)9, ô in [SCENE MODE]$ mode
[QUALITY] (P58)$ mode
DMC-FX35P_mst.book  103 ページ  ２００８年１月１５日　火曜日　午前１０時３６分 
						

							VQT1P09104
Others
[ASPECT RATIO] (P58)9 and ô in [SCENE MODE]
[INTELLIGENT ISO] (P58)[SCENE MODE]$ mode
[SENSITIVITY] (P59)[SCENE MODE]$ modeWhen Intelligent ISO is set
[WHITE BALANCE] (P59),, ., /, 1, 2, 3, ï, 5, 4, 6, 8, 7 and < in 
[SCENE MODE]
[WB ADJUST.] (P60)[B/W], [SEPIA], [COOL] or [WARM] in [COLOR MODE] is set
[QUICK AF] (P63)., /, 5 and 4 in [SCENE MODE]$ mode
[BURST] (P63)ô and 5 in [SCENE MODE]$ mode[AUDIO REC.]
[I.EXPOSURE] (P64)[SCENE MODE]$ mode
[COLOR MODE] (P64)[SCENE MODE]
[MIN. SHTR SPEED] (P65)[SCENE MODE]$ modeWhen Intelligent ISO is set
[AUDIO REC.] (P66)[AUTO BRACKET][BURST]ô and 5 in [SCENE MODE]$ mode
[AF ASSIST LAMP] (P66)0, ,, /, ï, 4 and 7 in [SCENE MODE]
Playback Zoom (P33)When playing back motion picturesStill pictures with audio (when playing back audio)
[TITLE EDIT] (P77)Motion picturesProtected picturesWhen component cable is connected
[TEXT STAMP] (P78)Pictures recorded without setting the clock Motion picturesStill pictures with audioPictures stamped with [TEXT STAMP]When component cable is connected
[RESIZE] (P79)Motion picturesStill pictures with audioPictures stamped with [TEXT STAMP]When component cable is connected
[TRIMMING] (P80)Motion picturesStill pictures with audioPictures stamped with [TEXT STAMP]When component cable is connected
[ASPECT CONV.] (P81)Pictures taken with Y or XMotion picturesStill pictures with audioPictures stamped with [TEXT STAMP]When component cable is connected
DMC-FX35P_mst.book  104 ページ  ２００８年１月１５日　火曜日　午前１０時３６分 
						

							105VQT1P09
Others
[ROTATE] (P82)Motion picturesProtected pictures
[ROTATE DISP.] (P82)Multi playback[CALENDAR]
PRINT WITH DATEPictures stamped with [TEXT STAMP]
[AUDIO DUB.] (P86)Motion picturesProtected picturesWhen component cable is connected
[COPY] (P87)When component cable is connected
DMC-FX35P_mst.book  105 ページ  ２００８年１月１５日　火曜日　午前１０時３６分 
						

							VQT1P09106
Others
Troubleshooting
First, try out the following procedures (P106–111).

The battery is not inserted correctly. (P14)The battery is exhausted.
Is [AUTO LCD OFF] (P21) of the [ECONOMY] mode active?
>Press the shutter button halfway to cancel these modes.
The battery is exhausted.
The battery is exhausted.If you leave the camera on, the battery will be exhausted.
>Turn the camera off frequently by using the [ECONOMY] mode etc. (P21)
Is the temperature of the battery excessively high or low? If it is, it will take longer than usual to 
charge the battery or charging may remain incomplete.
Are the terminals of the charger or battery dirty?
>Wipe off the dirt using a dry cloth.
Is the [REC]/[PLAYBACK] selector switch at the [!] setting? (P25)Is the mode dial correctly set?Is there any memory remaining on the built-in memory or the card?
>Delete the pictures which are not necessary to increase the available memory. (P34)
The picture can become whitish if there is dirt e.g. fingerprints on the lens.
>If the lens is dirty, turn on the camera, eject the lens barrel (P11) and gently wipe the lens 
surface with a soft dry cloth.
Was this picture taken with the flash at the close range when the zoom is near [W] (1k)?
>Zoom in a little, and then take the pictures. (P30)
>Check that the exposure is correctly compensated. (P43)
Setting the [MIN. SHTR SPEED] to faster speed might make the picture darker.
If the problem is not resolved, it may be improved by selecting [RESET] (P22) on the 
[SETUP] menu when taking pictures.
Battery and power source
The camera cannot be operated even when it is turned on.
The LCD monitor turns off while the camera is turned on.
The camera turns off immediately after it is turned on.
The [CHARGE] lamp flashes.
Recording
The picture cannot be recorded.
The recorded picture is whitish.
The area around where the pictures were taken becomes dark.
The recorded picture is too bright or dark.
DMC-FX35P_mst.book  106 ページ  ２００８年１月１５日　火曜日　午前１０時３６分 
						

							107VQT1P09
Others
>Set the [MIN. SHTR SPEED] to slower speed. 
>Set auto bracket (P44), [HI-SPEED BURST] (P49) in scene mode or [BURST] (P63) of the 
[REC] mode menu to [OFF].
The focus range varies depending on the recording mode.
>Set to the proper mode for the distance to the subject.
The subject is beyond the focus range of the camera. (P29)There is camera shake (jitter) or the subject is moving slightly. (P30)
>The shutter speed becomes slower when pictures are taken in dark places so hold the 
camera firmly with both hands to take the pictures. (P26)
>When taking pictures at a slow shutter speed, use the self-timer. (P42)
Is the number of recordable pictures 2 or less?
Is the ISO sensitivity high or the shutter speed slow?
(ISO sensitivity is set to [AUTO] when the camera is shipped. Therefore, when taking pictures 
indoors etc. noise will appear.)
>Decrease the ISO sensitivity. (P59)
>Set [COLOR MODE] to [NATURAL]. (P64)
>Take pictures in bright places.
Has [HIGH SENS.] or [HI-SPEED BURST] in the scene mode been set? If so, the resolution of the 
recorded picture decreases slightly because of high sensitivity processing, but this is not a malfunction.
If recording under fluorescent light, the brightness or the hue may change slightly when the shutter 
speed becomes fast. This occurs due to the characteristics of fluorescent light. It is not a malfunction.
Are you using a MultiMediaCard? This unit does not support MultiMediaCards.
>When you set the picture quality to [÷], [ý], [ü], or [ÿ], we recommend using a 
high-speed card with “10MB/s” or greater displayed on the package.
Depending on the type of the card, recording may stop in the middle.
2 or 3 pictures are taken at one time.
The subject is not focused properly.
The recorded picture is blurred. 
The optical image stabilizer is not effective.
Taking pictures using auto bracket is not possible.
The recorded picture looks rough. 
Noise appears on the picture.
The brightness or the hue of the recorded picture is different from the actual 
scene.
A reddish vertical line (smear) appears on the LCD monitor during picture-taking.
This is a characteristic of CCDs, and it appears when the subject has a 
bright part. Some unevenness may occur in the surrounding areas, but 
this is not a malfunction.
It is recorded in motion pictures but is not recorded on still pictures.
It is recommended that you take pictures while taking care not to expose 
the screen to sunlight or any other source of strong light.
Motion picture recording stops in the middle.
DMC-FX35P_mst.book  107 ページ  ２００８年１月１５日　火曜日　午前１０時３６分 
						

							VQT1P09108
Others
It is possible that the subject may be warped slightly, or the borders get colored, depending on 
the zoom magnification, due to the characteristics of the lens. Also, the peripherals of the 
image might look warped because the perspective is enhanced when the wide angle is used. 
This is not a malfunction.
The LCD monitor turns off and the status indicator lights when [AUTO LCD OFF] (P21) is 
selected for the [ECONOMY] mode. 
[This does not happen when using the AC adaptor (DMW-AC5PP; optional).] 
If the remaining battery power is low, it may take longer for the flash to be charged, and the time 
during which the LCD monitor is turned off may become longer.
This phenomenon appears when you press the shutter button halfway to set the aperture value 
and does not affect the recorded pictures.
The LCD monitor may flicker for a few seconds after turning the camera on indoors under 
fluorescent light. This is not a malfunction.
>Adjust the brightness of the screen. (P20)
[POWER LCD] or [HIGH ANGLE] is activated. (P20)
This is not a malfunction.
These pixels do not affect the recorded pictures.
In dark places, noise may appear to maintain the brightness of the LCD monitor. This does not 
affect the pictures you are recording.
Is the flash setting set to [Œ]?
>Change the flash setting. (P38)
Flash mode is not available when auto bracket (P44) or [BURST] (P63) in [REC] mode menu 
has been set.
The flash is activated twice when red-eye reduction (P38) has been set.
Lens
Recorded image may be warped, or nonexistent color is surrounding the subject.
LCD monitor
The LCD monitor turns off although the camera is turned on.
The LCD monitor becomes darker or brighter for a moment.
The LCD monitor flickers indoors.
The LCD monitor is too bright or dark.
Black, red, blue and green dots appear on the LCD monitor.
Noise appears on the LCD monitor.
Flash
The flash is not activated.
The flash is activated 2 times.
DMC-FX35P_mst.book  108 ページ  ２００８年１月１５日　火曜日　午前１０時３６分 
						

							109VQT1P09
Others
[ROTATE DISP.] (P82) is set to [ON].You can rotate pictures with the [ROTATE] function. (P82)
Is the [REC]/[PLAYBACK] selector switch set to [(]? (P32)Is there a picture on the built-in memory or the card?
>The pictures on the built-in memory appear when a card is not inserted. The picture data on 
the card appears when a card is inserted.
Is this a picture whose file name has been changed in the PC? If it is, it cannot be played back by this unit.
Has [CATEGORY PLAY] or [FAVORITE PLAY] been set for playback?
>Change to [NORMAL PLAY]. (P32)
Is this a non-standard picture, a picture which has been edited using a PC or a picture which 
was taken by another make of digital camera?
Did you remove the battery immediately after picture-taking or did you take the picture using a 
battery with a low remaining charge?
>Format the data to delete the pictures mentioned above. (P24)
(Other pictures will be deleted as well and it will not be possible to restore them. Therefore, 
check well before formatting.)
Is the clock in the camera set properly? (P16)When pictures edited using a PC or pictures taken by other equipment are searched, they may 
be displayed on dates differing from the actual dates on which the pictures were taken.
Is it a picture that has been recorded with other equipment? In such cases, these pictures may 
be displayed with a deteriorated picture quality.
This unit automatically adjusts the aperture during motion picture recording. At such times, a clicking 
sound is heard, and this sound may be recorded on the motion pictures. This is not a malfunction.
Playback
The picture being played back is rotated and displayed in an unexpected 
direction.
The picture is not played back.
The recorded pictures are not displayed.
The folder number and the file number are displayed as [—] and the screen turns 
black.
With a calendar search, pictures are displayed on dates differing from the actual 
dates on which the pictures were taken.
White round spots like soap bubbles appear on the recorded picture.

If you take a picture with the flash in a dark place or indoors, white 
round spots may appear on the picture caused by the flash reflecting of 
particles of dust in the air. This is not a malfunction. 
A characteristic of this is that the number of round spots and their 
position differ in every picture.
[THUMBNAIL IS DISPLAYED] appears on the screen.
A clicking sound is recorded in the motion pictures.
DMC-FX35P_mst.book  109 ページ  ２００８年１月１５日　火曜日　午前１０時３６分 
						

							VQT1P09110
Others
Is the camera connected to the TV correctly?
>Set the TV input to external input mode.
Output from the  [COMPONENT OUT] socket is not possible when it is connected to the PC or 
the printer.
>Connect it only to the TV.
Depending on the TV model, the pictures may be extended horizontally or vertically or they may 
be displayed with their edges cut off.
Are you trying to play back the motion pictures by directly inserting the card in the card slot of the TV?>Connect the camera to the TV with the AV  cable (supplied), or with the component cable 
(DMW-HDC2; optional), and then play back the motion pictures on the camera. (P94, 95)
>Check [TV ASPECT] setting. (P23)
Is the camera connected to the PC correctly?Is the camera recognized by the PC correctly?
>Set to [PC] in [USB MODE]. (P22, 88)
>
Disconnect the USB connection cable. Connect it again while the card is inserted in the camera.When the mode dial is set to  [¨] , contents of the built-in memory will be displayed.
>Set the mode dial to anything except  [¨].
Pictures cannot be printed using a printer which does not support PictBridge.
>Set to [PictBridge(PTP)] in [USB MODE]. (P22, 90)
>When using a printer with a trimming or borderless printing function, cancel this function 
before printing. (For details, refer to the operating instructions for the printer.)
>When you order photo studios to print pictures, ask the photo studio if the pictures can be 
printed with both ends.
>Press [MENU/SET], select the [SETUP] menu icon [ ] and then select the [~] icon to set 
the desired language. (P24)
TV, PC and printer
The picture does not appear on the television.
The display areas on the TV screen and the camera’s LCD monitor are different.
The motion pictures cannot be played back on a TV.
The picture is not displayed fully on the TV.
The picture cannot be transferred when the camera is connected to a PC.
The card is not recognized by the PC. (The built-in memory is recognized.)
The picture cannot be printed when the camera is connected to a printer.
The ends of the pictures are cut at printing.
Others
An unreadable language was selected by mistake.
DMC-FX35P_mst.book  110 ページ  ２００８年１月１５日　火曜日　午前１０時３６分