Panasonic Dmc Fx100 Operating Instructions Manual

							Advanced (Playback)
81VQT1F52
 If there are 1000 or more pictures, you 
can make a slide show with up to 999 
pictures.
3Press 2 to return to the category 
playback screen.
 ] and then press [MENU/SET] 
to close the menu.
 You cannot play back motion pictures as a 
slide show. 
 Still pictures created from a motion picture 
(P74) cannot be played back from the 
motion pictures category   in category 
playback.
Press [ ] to display the [PLAY] mode 
menu and select the item to set. (P76)
This mode allows you to automatically 
display pictures vertically if they were 
recorded holding the camera vertically or 
rotate pictures manually in 90° steps.
∫Rotate display
(The picture is automatically rotated and 
displayed.)
1Press 4 to select [ON] and then 
press [MENU/SET].
 The pictures are displayed without 
being rotated when you select [OFF].
 Refer to P32 for information about how 
to play back pictures.
2Press [MENU/SET] to close the 
menu.
∫Rotate
(The picture is rotated manually.)
1Press 2/1 to select the picture 
and then press 4.
 The [ROTATE] function is disabled 
when [ROTATE DISP.] is set to [OFF].
 Motion pictures and protected pictures 
cannot be rotated.
2Press 3/4 to select the direction 
to rotate the picture and then 
press [MENU/SET].
3Press [MENU/SET] twice to close 
the menu.
[ROTATE DISP.]/[ROTATE]
To display the picture rotated
MENU/SET
MENU/SET
The picture rotates clockwise in 
steps of 90°.
The picture rotates 
counter-clockwise in steps of 90°.
MENU/SET
DMC-FX100ENG.book  81 ページ  ２００７年５月１６日　水曜日　午後３時２２分 
						

							Advanced (Playback)
82VQT1F52
 If you take pictures when aiming the 
camera up or down, it may not be possible 
to display the pictures vertically.
 The picture may be slightly blurred when 
the camera is connected to the TV with 
the AV cable (supplied) and played back 
vertically.
 When you play back pictures on a PC, 
they cannot be displayed in the rotated 
direction unless the OS or software is 
compatible with Exif. Exif is a file format 
for still pictures which allows recording 
information etc. to be added. It was 
established by “JEITA (Japan Electronics 
and Information Technology Industries 
Association)”.
 Rotated pictures are displayed rotated 
when they are played back in review 
playback and playback zoom however are 
displayed without being rotated when they 
are played back in multi playback.
 It may not be possible to rotate pictures 
that have been recorded with other 
equipment.
Press [ ] to display the [PLAY] mode 
menu and select the item to set. (P76)
You can stamp the date and time of 
recording, the age and the travel date on 
the recorded pictures.
It is suitable for regular size printing. 
(Pictures with a picture size larger than 
[ ] will be resized when stamping the 
date etc. on them.)
Press 3/4 to select [SINGLE] or 
[MULTI] and then press [MENU/
SET].
 The date information cannot be 
stamped on the following pictures.
– Pictures recorded without setting the 
clock
– Pictures recorded with other 
equipment
– Pictures that were previously stamped 
with [DATE STAMP]
– Motion pictures
– Pictures with Audio
∫Single setting
1Press 2/1 to select the picture 
and then press4.
2Press 3/4/2/1 to select 
[SHOOTING DATE], [AGE] or 
[TRAVEL DATE] and then press 
[MENU/SET] to set each item.
[DATE STAMP]
Stamping information such as the 
date on the recorded pictures
MENU/SET
MENU/SET
MENU/SET
DMC-FX100ENG.book  82 ページ  ２００７年５月１６日　水曜日　午後３時２２分 
						

							Advanced (Playback)
83VQT1F52
[SHOOTING DATE]
[AGE]
If this is set to [ON], the age is stamped 
on pictures recorded when the camera 
was set to [WITH AGE].
[TRAVEL DATE]
If this is set to [ON], the travel date is 
stamped on pictures recorded when 
[TRAVEL DATE] was set to [ON].
3Press [MENU/SET].
 If you set [DATE STAMP] for a picture 
with a picture size larger than [ ], the 
picture size will become smaller as 
shown below.
 The picture becomes slightly rougher.
4Press 3/4 to select [YES] or 
[NO] and then press [MENU/SET].
(The screen shown appears when you 
select a picture recorded with a [ ] 
picture size.)
 The message [DELETE ORIGINAL 
PICTURE?] appears if the picture was 
recorded with a picture size [ ] or 
less. The picture is overwritten when you 
select [YES]. Pictures stamped with 
date stamp cannot be restored when 
they are overwritten.
 The picture stamped with date stamp is 
newly created when you select [NO].
 If the original picture is protected, you 
cannot overwrite it. Select [NO] and 
newly create the picture stamped with 
date stamp.
5Press [MENU/SET] twice to close 
the menu.
 The date stamp icon [ ]  A appears 
on the screen if the picture has been 
stamped with the date stamp.
 Use the playback zoom (P72) to check 
the stamped date information B.
∫Multi setting
1Press 2/1 to select the picture 
and then press 4 to SET/
CANCEL.
 Repeat this step. [W/O TIME]Stamp the year, month 
and date.
[WITH TIME]Stamp the year, month, 
day, hour and minutes.
Aspect ratio 
settingPicture size
//>
//>
//>
MENU/SET[SET]The [DATE STAMP] icon A 
appears.
[CANCEL]The [DATE STAMP] icon A 
disappears.
A
B
A
DMC-FX100ENG.book  83 ページ  ２００７年５月１６日　水曜日　午後３時２２分 
						

							Advanced (Playback)
84VQT1F52
2Press [MENU/SET].
After performing step 2, perform 
step 2 onwards in “Single setting”.
When you print pictures stamped with 
the date stamp, the date will be printed 
over the stamped date if you set date 
printing at the photo printing store or 
on the printer.
 We recommend setting date stamp when 
there is plenty of space on the built-in 
memory or the card.
 You can set up to 50 pictures at one time 
in [MULTI].
 If you select [YES] in step 
4 when the 
pictures selected in [MULTI] include 
protected pictures, the message appears 
and only the protected pictures cannot be 
stamped with date stamp.
 Depending on the printer being used, 
some characters may be cut at printing. 
Check before printing.
 You cannot use the following functions if 
the date information has been stamped on 
the picture.
– [DATE STAMP]
– The [PRINT WITH DATE] setting for 
DPOF print 
–[RESIZE]
–[TRIMMING]
– [ASPECT CONV.]
Press [ ] to display the [PLAY] mode 
menu and select the item to set. (P76)
DPOF “Digital Print Order Format” is a 
system that allows the user to select which 
pictures to print, how many copies of each 
picture to print and whether or not to print 
the recording date on the pictures when 
using a DPOF compatible photo printer or photo printing store. For details, ask at your 
photo printing store.
When you want to use a photo printing 
store to print pictures recorded on the 
built-in memory, copy them to a card (P90) 
and then set the DPOF setting.
For more information visit:
http://panasonic.jp/dc/dpof_110/
white_e.htm
Press 3/4 to select [SINGLE], 
[MULTI] or [CANCEL] and then 
press [MENU/SET].
 You cannot select [CANCEL] if there 
are no prints that have been set in the 
DPOF print settings.
∫Single setting
1Press 2/1 to select the picture to 
print and then press 3/4 to set 
the number of prints.
 The number of prints icon [ ] A 
appears.
 The number of prints can be set from 
0 to 999. The DPOF print setting is 
canceled when the number of prints is 
set to [0].
2Press [MENU/SET] twice to close 
the menu.
[DPOF PRINT]
Setting the picture to print and the 
number of prints
MENU/SET
MENU/SET
A
DMC-FX100ENG.book  84 ページ  ２００７年５月１６日　水曜日　午後３時２２分 
						

							Advanced (Playback)
85VQT1F52
∫Multi setting
1Press 2/1 to select the picture to 
print and then press 3/4 to set 
the number of prints.
 The number of prints icon [ ] B 
appears.
 Repeat the above procedure. (You 
cannot set all the pictures at one time.)
 The number of prints can be set from 
0 to 999. The DPOF print setting is 
canceled when the number of prints is 
set to [0].
2Press [MENU/SET] twice to close 
the menu.
∫To cancel all settings
1Press 3 to select [YES] and then 
press [MENU/SET].
2Press [MENU/SET] to close the 
menu.
 DPOF print settings on the built-in 
memory are canceled when a card is 
not inserted. DPOF print settings on the 
card are canceled when a card is 
inserted.
∫To print the date
After setting the number of prints, set/
cancel printing with the recording date by 
pressing [DISPLAY].
 The date print icon [ ] C appears.
 When you go to a photo printing store for 
digital printing, be sure to order the 
printing of the date additionally if required.
 Depending on the photo printing store or 
the printer, the date may not be printed 
even if you set to print the date. For further 
information, ask at your photo printing 
store or refer to the operating instructions 
for the printer.
 You cannot set date printing if the pictures 
have been stamped with the date stamp.
 If you set [DATE STAMP] for pictures that 
have been set for date printing, the date 
printing setting is canceled.
 DPOF is an abbreviation of “Digital Print 
Order Format”. This feature allows you to 
write print information to media and then 
use the information on a DPOF-compliant 
system.
 DPOF print setting is a convenient 
function when printing pictures with a 
printer that supports PictBridge. The date 
printing setting on the printer may take 
priority over the date printing setting on 
the camera. Check the date printing 
setting on the printer also. (P94)
 It is necessary to delete all previous 
DPOF print information made on other 
equipment when setting DPOF print on 
the camera.
 If the file is not based on the DCF 
standard, the DPOF print setting cannot 
be set.
B
MENU/SET
C
DATE
DMC-FX100ENG.book  85 ページ  ２００７年５月１６日　水曜日　午後３時２２分 
						

							Advanced (Playback)
86VQT1F52
Press [ ] to display the [PLAY] mode 
menu and select the item to set. (P76)
You can set protection for pictures you do 
not want to be deleted by mistake.
Press 3/4 to select [SINGLE], 
[MULTI] or [CANCEL] and then 
press [MENU/SET].
∫Single setting
1Press 2/1 to select the picture 
and then press 4 to SET/
CANCEL.
2Press [MENU/SET] twice to close 
the menu.
∫Multi setting/To cancel all settings
Perform the same operation as in 
“[DPOF PRINT]”. (P84 to 85)
 If you press [MENU/SET] while canceling 
protection, the canceling will stop halfway.
 The protect setting may not be effective 
on other equipment.
 If you want to delete protected pictures, 
cancel their protection.
 Even if you protect pictures in the built-in 
memory or a card, they will be deleted if 
the built-in memory or the card is 
formatted.
 Even if you do not protect pictures on an 
SD Memory Card or an SDHC Memory 
Card, they cannot be deleted when the 
card’s Write-Protect switch B is set to 
[LOCK].
 The following functions cannot be used 
with protected pictures.
–[ROTATE]
– [AUDIO DUB.]
Press [ ] to display the [PLAY] mode 
menu and select the item to set. (P76)
You can add the audio after taking a 
picture.
1Press 2/1 to select the picture 
and then press 4 to start audio 
recording.
[PROTECT]
Preventing accidental erasure of 
pictures
[SET]The protect icon [ ] A 
appears.
[CANCEL]The protect icon [ ] A 
disappears.
MENU/SET
MENU/SET
A[AUDIO DUB.] 
Adding audio after taking pictures
2
MENU/SET
DMC-FX100ENG.book  86 ページ  ２００７年５月１６日　水曜日　午後３時２２分 
						

							Advanced (Playback)
87VQT1F52
 The message [OVERWRITE AUDIO 
DATA?] screen appears when audio has 
already been recorded. Press 3 to 
select [YES] and then press [MENU/
SET] to start audio recording. (The 
original audio is overwritten.)
 Audio dubbing cannot be used with the 
following pictures.
– Motion pictures
– Protected pictures
2Press 4 to stop recording.
 The audio recording stops 
automatically if 4 is not pressed after 
about 10 seconds.
3Press [MENU/SET] twice to close 
the menu.
 Audio dubbing may not work properly on 
pictures recorded by other equipment.
Press [ ] to display the [PLAY] mode 
menu and select the item to set. (P76)
We recommend resizing to   if you want 
to attach a picture to an e-mail or use it on 
a website.
1Press 2/1 to select the picture 
and then press 4.
2Press 2/1 to select the size and 
then press 4.
 Sizes smaller than the recorded picture 
are displayed.
 The message [DELETE ORIGINAL 
PICTURE?] appears.
3Press 3/4 to select [YES] or 
[NO] and then press [MENU/SET].
 The picture is overwritten when you 
select [YES]. Resized pictures cannot 
be restored when they are overwritten.
 A resized picture is newly created when 
you select [NO].
 If the original picture is protected, you 
cannot overwrite it. Select [NO] and 
newly create a resized picture.
4Press [MENU/SET] twice to close 
the menu.
[RESIZE]
Making the picture size smaller
MENU/SET
Aspect ratio 
settingPicture size
///
/
//
//
MENU/SET
DMC-FX100ENG.book  87 ページ  ２００７年５月１６日　水曜日　午後３時２２分 
						

							Advanced (Playback)
88VQT1F52
 The following pictures cannot be resized.
– Motion pictures
– Pictures with audio
– Pictures stamped with [DATE STAMP]
 It may not be possible to resize pictures 
recorded with other equipment.
Press [ ] to display the [PLAY] mode 
menu and select the item to set. (P76)
You can enlarge and then clip the important 
part of the recorded picture.
1Press 2/1 to select the picture 
and then press 4.
 The following pictures cannot be 
trimmed.
– Motion pictures
– Pictures with audio
– Pictures stamped with [DATE STAMP]
2Enlarge or decrease the parts to 
be trimmed with the zoom lever.
3Press 3/4/2/1 to move the 
position of the part to be trimmed.
4Press the shutter button.
 The message [DELETE ORIGINAL 
PICTURE?] appears.
5Press 3/4 to select [YES] or 
[NO] and then press [MENU/SET].
 The picture is overwritten when you 
select [YES]. The trimmed pictures 
cannot be restored when they are 
overwritten.
 A trimmed picture is newly created 
when you select [NO].
 When the original picture is protected, 
you cannot overwrite it. Select [NO] and 
newly create a trimmed picture.
6Press [MENU/SET] twice to close 
the menu.
 Depending on the cut size, the picture size 
of the trimmed picture may become 
smaller than that of the original picture.
 The picture quality of the trimmed picture 
will deteriorate.
 It may not be possible to trim pictures 
recorded with other equipment.
Aspect ratio 
settingPicture size
[TRIMMING]
Enlarging a picture and trimming it
MENU/SET
MENU/SET
DMC-FX100ENG.book  88 ページ  ２００７年５月１６日　水曜日　午後３時２２分 
						

							Advanced (Playback)
89VQT1F52
Press [ ] to display the [PLAY] mode 
menu and select the item to set. (P76)
You can convert pictures taken with a 
[ ] aspect ratio to a [ ] or a [ ] 
aspect ratio.
1Press 3/4 to select [ ] or 
[ ] and then press [MENU/SET].
 The following pictures cannot be 
converted.
– Motion pictures
– Pictures with audio
– Pictures stamped with [DATE STAMP]
2Press 2/1 to select a picture and 
then press 4.
 If you select and set a picture with an 
aspect ratio other than [ ], the 
message 
[CANNOT BE SET ON THIS PICTURE] 
is displayed on the screen.
3Press 2/1 to determine the 
horizontal position and press the 
shutter button to set.
 Use 3/4 to set the frame position for 
pictures rotated vertically.
 The message [DELETE ORIGINAL 
PICTURE?] appears.
4Press 3/4 to select [YES] or 
[NO] and then press [MENU/SET].
 The picture is overwritten when you 
select [YES]. If you convert the aspect 
ratio of a picture and then overwrite it, 
you cannot restore it.
 A picture with the converted aspect 
ratio is newly created when you select 
[NO].
 When the original picture is protected, 
you cannot overwrite it. Select [NO] and 
newly create a picture with the 
converted aspect ratio.
5Press [MENU/SET] twice to close 
the menu.
 After converting the aspect ratio, the 
picture size may become larger than that 
of the original picture.
 Files that do not conform to the DCF 
standard cannot be converted.
 You may not be able to convert pictures 
taken on other equipment.
[ASPECT CONV.]
Changing the aspect ratio of a 16:9 
picture
MENU/SET
MENU/SET
MENU/SET
DMC-FX100ENG.book  89 ページ  ２００７年５月１６日　水曜日　午後３時２２分 
						

							Advanced (Playback)
90VQT1F52
Press [ ] to display the [PLAY] mode 
menu and select the item to set. (P76)
You can copy recorded picture data from 
the built-in memory to a card or vice versa.
1Press 3/4 to select the copy 
destination and then press 
[MENU/SET].

All the picture data in the built-in 
memory are copied onto the card at 
one time. > step 
3.

One picture at a time is copied from the 
card to the built-in memory. > step 
2.
2Press 2/1 to select the picture 
and then press 4.
(Only when selecting [ ])
3Press 3 to select [YES] and then 
press [MENU/SET].
(The illustration shows the screen when 
pictures are copied from the built-in 
memory to a card.)
 The message [COPY THIS PICTURE 
TO BUILT-IN MEMORY?] appears when 
you copy pictures from the card to the 
built-in memory. If you press [MENU/SET] while copying 
pictures from the built-in memory to the 
card, the copying will stop halfway.
 Do not turn the camera off or perform 
any other operations before copying is 
finished. The data on the built-in 
memory or the card may be damaged 
or lost.
4Press [MENU/SET] several times 
to close the menu.
 If you copy from the built-in memory to 
a card, all the pictures are copied and 
then the screen automatically returns to 
the playback screen.
 If you copy picture data from the built-in 
memory to a card which does not have 
sufficient free space, the picture data will 
only be copied halfway. We recommend 
using a card which has more free space 
than the built-in memory (about 27 MB). 

f a picture exists with the same name 
(folder number/file number) as the picture to 
be copied in the copy destination when
 
[] is selected, a new folder is 
created and the picture is copied.
If a picture exists with the same name 
(folder number/file number) as the picture 
to be copied in the copy destination when 
[] is selected, that picture is not 
copied.
 It may take time to copy the picture data.
 Only pictures recorded with a Panasonic 
digital camera (LUMIX) will be copied.
(Even if the pictures were recorded with a 
Panasonic digital camera, you may not be 
able to copy them if they were edited with 
a PC.)
 DPOF settings on the original picture data 
will not be copied. Set the DPOF settings 
again after copying is finished. (P84)
[COPY]
Copying the picture data
MENU/SET
MENU/SET
MENU/SET
DMC-FX100ENG.book  90 ページ  ２００７年５月１６日　水曜日　午後３時２２分