Panasonic DLP Projector Pt Tw330 Operating Instructions

							On-screen Display Menus
ENGLISH - 31
Settings
How to operate menu
Operation steps J
Press  button on the remote control or on the control panel.1 ) 
Main Menu displays. z
Use ▲▼ to select any item in the Main Menu.2 ) 
The selected item is highlighted in orange. z
Press 3 ) ►.
Items in the Sub Menu can be selected. z
Use ▲▼ to select any item in the Sub Menu.4 ) 
The selected item is highlighted in yellow.  z
Press 5 ) ► to display adjusting box.
Use ▲▼ to switch or adjust all settings.6 ) 
Press  button to go back to the Sub Menu and press again to go bac\
k to the 7 ) 
Main Menu, press  button once more to close the Main Menu.
PT-TW330
Note
Some items may not be adjusted or used for certain signal formats input to the projector . The MENU items that cannot be  z
adjusted or used are shown in gray characters, and they cannot be select\
ed.
Some items can be adjusted even if signals are not input. z
If there is no operation to the projector for about 30 seconds, the Menu screen and the adjusting screen will disappear  z
automatically.
See pages 32 and 33 for details on the items of Sub Menu. z
Main Menu
Sub Menu
Setting Value
or
Adjusting Value
On-screen Display Menus
Settings 
						

							On-screen Display Menus
32 - ENGLISH
Settings
Menu Tree
Main MenuSub Menu2nd Sub MenuDefault ValueRange
Picture
Color ModeDynamic / PC / Movie / Game / User
Wall colorWhite / Light Yellow / Light Blue / 
Pink / Dark Green
White
Brightness0 ~ 100
Contrast0 ~ 100
Sharpness0 ~ 31
Saturation0 ~ 100
Hue0 ~ 100
Gamma0 ~ +3
Color Temp.Low / Mid / High
Color SpaceAuto / RGB / YUVAuto
Position
Aspect RatioAuto / 4:3 / 16:9 / 16:10Auto
Phase0 ~ 31
Clock-5 ~ 5
H. Position
V. Position
Digital Zoom00 ~ 10
V Keystone0-40 ~ 40
Ceiling MountFront / Front Ceiling / Rear / Rear 
Ceiling
Front
Setting
LanguageEnglish / German / Spanish / French / 
Italian / Dutch / Portuguese /
Japanese/ Simplified Chinese / 
Polish / Korean / Russian / Swedish /
Traditional Chinese/Arabic / 
Norwegian / Turkish / Thai / Czech /
Hungarian / Kazakh
English
Menu LocationLeft Top / Right Top / Center / Left 
Bottom / Right Bottom
Center
Closed CaptionOff / CC1 / CC2 / CC3 / CC4Off
VGA Out (Standby)On / OffOff
Test PatternOn / OffOff
Remote IDAll / ID1 / ID2 / ID3 / ID4 / ID5 / ID6All
Startup LogoOn / OffOn
UART ModeLAN / RS-232LAN
LAN (Standby)On / OffOff
ResetYes / NoNo
Audio
MuteOn / OffOff
Volume200 ~ 32
In Standby Mode 
(Audio)
On / OffOff 
						

							On-screen Display Menus
ENGLISH - 33
Settings
Main MenuSub Menu2nd Sub MenuDefault ValueRange
Options
Auto SourceOn / OffOn
InputHDMI, Computer 1, Computer 2,
Video
Auto Power Off (Min)00~120
Lamp Settings
Lamp Hours Used (Normal)0
Lamp Hours Used (ECO)0
Lamp Life 
Reminder
Off/OnOn
Lamp
Power
Mode
Normal / Auto / ECO1 / 
ECO2 for PT-TW330E / 
PT-TX300E.
Normal / Auto / ECO for 
PT-TW240E.
Normal
Clear 
Lamp 
Hours
Yes / NoNo
High AltitudeOn / OffOff
Dust Filter ReminderFilters Remind (Hour)00 ~ 1000
Cleaning 
up 
reminder
Yes / NoNo
InformationModel Name
Source
Resolution
Software Version
Color Space
Aspect Ration
LAN
DHCPOn / OffOff
IP Address 192.168.10.100
Subnet Mask255.255.255.0
Gateway192.168.10.1
DNS0.0.0.0
StoreYes / No
ResetYes / No
Note
  Please note that the on-screen display (OSD) menus vary according to the signal type selected and the projector model  z
you are using.
[Sharpness], [Saturation] and [Hue] are only supported in Video mode.  z 
						

							Picture
34 - ENGLISH
Settings
Picture
Select [Picture] from the Main Menu (see “How 
to operate menu” on page 31) and then select 
the item from the Sub Menu.
PT-TW330
Color Mode
There are many factory presets optimized for various 
types of images.
Press ▲▼ to select [Color Mode].1 ) 
Press ► to display the choosing dialog 2 ) 
box.
Press ◄► to select the desired item.3 ) 
DynamicFor bright room.
PCFor computer or notebook.
MovieFor home theater.
GameFor amusing games.
UserFor user's favorite image mode.
Note
When [Dynamic], [PC], [Movie] or [Game] is selected,  z
the value of [Brightness], [Contrast], [Sharpness], 
[Saturation], [Hue], [Gamma], [Color Temp] will be fixed.
When [Brightness], [Contrast], [Sharpness], [Saturation],  z
[Hue], [Gamma], [Color Temp] is adjusted, [Color Mode] 
will change to [User].
The value of [User] depends on the type of the input  z
signal. 
Video, 480i/576i, 480p/576p, 720p, 1080i, 1080p, 
RGB, HDMI (YUV), HDMI (RGB).
Wall color
Select an appropriate color for wall projection.
Press ▲▼ to select [Wall color].1 ) 
Press ► to display the choosing dialog 2 ) 
box.
Press ◄► to select the desired item.3 ) 
WhiteFor White color.
Light YellowFor Light Yellow color.
Light BlueFor Light Blue color.
PinkFor Pink color.
Dark GreenFor Dark Green color.
Note
[Wall Color] does not support movie-based video signals. z
Brightness
You can adjust the dark (black) part of the projected image.
Press ▲▼ to select [Brightness].1 ) 
Press ► to display the adjustment 2 ) 
dialog box.
Press ◄► to adjust the setting value.3 ) 
OperationAdjustmentAdjustment 
range
Press ►.
Increases the 
brightness of the 
dark (black) parts of 
the screen.
Maximum 
value 100
Press ◄.
Reduces the 
brightness of the 
dark (black) parts of 
the screen.
Minimum 
value 0
Contrast
You can adjust the contrast of the colors.
Press ▲▼ to select [Contrast].1 ) 
Press ► to display the adjustment 2 ) 
dialog box.
Press ◄► to adjust the setting value.3 ) 
OperationAdjustmentAdjustment 
range
Press ►.
Brightens the screen 
and makes the color 
of image deeper.
Maximum 
value 100
Press ◄.
Darkens the screen 
and makes the color 
of image lighter.
Minimum 
value 0
Sharpness
You can adjust the sharpness of the projected image.
Press ▲▼ to select [Sharpness].1 )  
						

							Picture
ENGLISH - 35
Settings
Press ► to display the adjustment 2 ) 
dialog box.
Press ◄► to adjust the setting value.3 ) 
OperationAdjustmentAdjustment range
Press ►.Contours become sharper.Maximum value 31
Press ◄.Contours become softer.Minimum value 0
Note
During Video input signal, [Sharpness] can be adjusted. z
When [RGB] is selected at [Color Space] menu,  z
[Sharpness] is disable. 
Saturation
Adjust a video image from black and white to fully 
saturated color.
Press ▲▼ to select [Saturation].1 ) 
Press ► to display the adjustment 2 ) 
dialog box.
Press ◄► to adjust the setting value.3 ) 
OperationAdjustmentAdjustment range
Press ►.Increase the intensity of the color.Maximum value 100
Press ◄.Decrease the intensity of the color.Minimum value 0
Note
During Video input signal, [Saturation] can be adjusted. z
When [RGB] is selected at [Color Space] menu,  z
[Saturation] is disable. 
Hue
Adjust the skin tone.
Press ▲▼ to select [Hue].1 ) 
Press ► to display the adjustment 2 ) 
dialog box.
Press ◄► to adjust the setting value.3 ) 
OperationAdjustmentAdjustment range
Press ►.Adjust the skin tone to be green.Maximum value 100
Press ◄.Adjust the skin tone to be red.Minimum value 0
Note
During Video input signal and when the color mode is  z
NTSC or NTSC 4.43, [Hue] can be adjusted.
When [RGB] is selected at [Color Space] menu, [Hue] is  z
disable. 
Gamma
Adjust the gamma table when the dark areas or bright 
areas of the image is not clear.
Press ▲▼ to select [Gamma].1 ) 
Press ► to display the adjustment 2 ) 
dialog box.
Press ◄► to adjust the setting value.3 ) 
OperationAdjustmentAdjustment range
Press ►.Emphasize detail in dark areas of image.Maximum value +3
Press ◄.Emphasize detail in bright areas of image.
Minimum value 0
Color Temp
Select the color temperature.
Press ▲▼ to select [Color Temp].1 ) 
Press ► to display the choosing dialog 2 ) 
box.
Press ◄► to select the desired item.3 ) 
LowThe screen looks warmer.
MidThe medium color temperature.
HighThe screen looks colder.
Color Space
Select an appropriate color matrix type from Auto, 
RGB or YUV.
Press ▲▼ to select [Color Space].1 ) 
Press ► to display the choosing dialog 2 ) 
box.
Press ◄► to select the desired item.3 ) 
AutoSwitched automatically according to the input signal.
RGBFor computer input.
YUVFor component input.
Note
During Video input signal, [Color Space] will be in gray  z
and can not be operated. 
						

							Position
36 - ENGLISH
Settings
Position
Select [Position] from the Main Menu (see “How 
to operate menu” on page 31) and then select 
the item from the Sub Menu.
PT-TW330
Aspect Ratio
Use this function to choose your desired aspect ratio.
Press ▲▼ to select [Aspect Ratio].1 ) 
Press ► to display the choosing dialog 2 ) 
box.
Press ◄► to select the desired item.3 ) 
Auto
The projector identifies the video ID 
(VID) embedded in the image signals 
and displays the image by automatically 
switching the screen sizes between 4:3 
and 16:9.
4:3
When standard signals*1 are input, the 
pictures are displayed without changing 
the aspect ratio.
When wide-screen signals*2 are input, 
the pictures are displayed with the 
aspect ratio converted to 4*3.
16:9
When standard signals*1 are input, the 
pictures are displayed with the aspect 
ratio converted to 16:9.
When wide-screen signals*2 are input, 
the pictures are displayed without 
changing the aspect ratio.
16:10This format is for 16:10 input sources, 
like wide screen laptop.
*1:   Standard signals are input signals with an aspect 
ratio of 4:3 or 5:4.
*2:  Wide-screen signals are input signals with an 
aspect ratio of 16:10, 16:9, 15:9 or 15:10. 
Note
If an aspect ratio which is different from the aspect ratio  z
for the input signals is selected, the pictures will appear 
differently from the originals. Be careful of this when 
selecting the aspect ratio.
If using this projector in places such as cafes or hotels to  z
display programs for a commercial purpose or for public 
presentation, note that adjusting the aspect ratio or using 
the zoom function to change the screen pictures may 
be an infringement of the rights of the original copyright 
owner for that program under copyright protection laws. 
Take care when using a function of the projector such as 
the aspect ratio adjustment, zoom function, etc.
If conventional (normal) 4:3 pictures which are not wide- z
screen pictures are displayed on a wide screen, the 
edges of the pictures may not be visible or they may 
become distorted. Such pictures should be viewed as 
with an aspect ratio of 4*3 in the original format intended 
by the creator of the pictures.
Phase
Adjust to achieve an optimal image when there is a 
flickering image.
Press ▲▼ to select [Phase].1 ) 
Press ► to display the adjustment 2 ) 
dialog box.
Press ◄► to adjust the level.3 ) 
Note
During Computer input signal, [Phase] can be adjusted. z
Clock
Adjust to achieve an optimal image when there is a 
vertical flicker in the image.
Press ▲▼ to select [Clock].1 ) 
Press ► to display the adjustment 2 ) 
dialog box.
Press ◄► to adjust the level.3 ) 
Note
During Computer input signal, [Clock] can be adjusted. z
H Position
Shift the projected image position horizontally.
Press ▲▼ to select [H Position].1 ) 
Press ► to display the adjustment 2 ) 
dialog box.
Press ◄► to adjust the level.3 ) 
Note
During Computer input signal, [H Position] can be  z
adjusted. 
						

							Position
ENGLISH - 37
Settings
V Position
Shift the projected image position vertically.
Press ▲▼ to select [V Position].1 ) 
Press ► to display the adjustment 2 ) 
dialog box.
Press ◄► to adjust the level.3 ) 
Note
During Computer input signal, [V Position] can be  z
adjusted.
Digital Zoom
Adjust the magnification of the image. Magnification 
can be set from 1.0x to 2.0x in 0.1 increments.
Press ▲▼ to select [Digital Zoom].1 ) 
Press ► to display the adjustment 2 ) 
dialog box.
Press ◄► to adjust the level.3 ) 
Note
When the [Digital Zoom] is in the enlarge status, exits the  z
menu screen and the [Zoom] picture will display at the 
bottom left of the screen. This indicates the zoom 
function is in use. 
Under the enlarge status, press ▲▼◄► to move the  z
enlarged image.
If the input signal is changed under the enlarge status,  z
the magnification of [Digital Zoom] will be reset.
V Keystone
This function is used to adjust keystone distortion of 
the projected image.
Press ▲▼ to select [V Keystone].1 ) 
Press ► to display the adjustment 2 ) 
dialog box.
Press ◄► to adjust the level.3 ) 
Use the  (▲▼) buttons on the  z
remote control to adjust. 
OperationScreen image
Press the ▲► on 
the remote  control 
or the ► on the 
control panel to 
adjust the upper of 
the keystone.
Press the ▼◄ on 
the remote control 
or the ◄ on the 
control panel to 
adjust the bottom of 
the keystone.
Note
The adjusted keystone distortion will store automatically  z
even when the signal is interrupted or the AC power cord 
is plugged out or turned off the projector.
When the larger amount of keystone correction, the  z
picture quality will degrade and it will get harder to focus 
with more correction. Set the projector so the correction 
will be as small as possible.
When keystone correction is performed, the screen size  z
will also change.
Part of Closed caption may not be displayed when high  z
compensation values are set in [V Keystone].
Ceiling Mount
This function is used to project the image from a 
ceiling-mounted projector.
Press ▲▼ to select [Ceiling Mount].1 ) 
Press ► to display the choosing dialog 2 ) 
box.
Press ◄► to select the desired item.3 ) 
FrontWhen setting on a desk/floor and 
projecting from forward.
Front
Ceiling
When mounting on the ceiling and 
projecting forward.
Rear
When setting on a desk/floor and 
projecting rear (Using translucent 
screen).
Rear
Ceiling
When mounting on the ceiling and 
projecting from rear (Using translucent 
screen). 
						

							Setting
38 - ENGLISH
Settings
Setting
Select [Setting] from the Main Menu (see “How 
to operate menu” on page 31) and then select 
the item from the Sub Menu.
PT-TW330
Language
The language used in the On-Screen Menu is 
available in English, German, Spanish, French, Italian, 
Dutch, Portuguese, Japanese, Simplified Chinese, 
Polish, Korean, Russian, Swedish, Traditional 
Chinese, Arabic, Norwegian, Turkish, Thai, Czech, 
Hungarian and Kazakh.
Press ▲▼ to select [Language].1 ) 
Press ► to display the language dialog 2 ) 
box.
Press ▲▼ to select the desired item 3 ) 
and press ► to choose.
Menu Location
Switch the menu location on the display screen.
Change order: Left Top  z Right Top  Center 
 Left Bottom  Right Bottom.
Press ▲▼ to select [Menu Location].1 ) 
Press ► to display the setting dialog 2 ) 
box.
Press ◄► to select the desired item.3 ) 
Closed Caption
[Only for NTSC input].
Press ▲▼ to select [Closed Caption].1 ) 
Press ► to display the setting dialog box.2 ) 
Press ◄► to select the desired item.3 ) 
OffDo not display Closed Caption.
CC1Displays the CC1 data.
CC2Displays the CC2 data.
CC3Displays the CC3 data.
CC4Displays the CC4 data.
Note
The closed caption is mainly used in the north America.  z
This function shows the text  information contained in the 
image signal. Captions may not be displayed on some 
devices or software.
You can select [Closed Caption] only when NTSC signal  z
is input.
When Menu screen is displayed, the caption will not be  z
displayed.
Part of Closed caption may not be displayed when high  z
compensation values are set in [V Keystone].
VGA Out (Standby)
When in standby mode, choose whether to output the 
signal from  to  
terminal.
Press ▲▼ to select [VGA Out (Standby)].1 ) 
Press ► to display the setting dialog 2 ) 
box.
Press ◄► to switch [On]/[Off].3 ) 
On
Output image signal from  
 terminal when the 
projector is in standby mode.
Off
Image signal from  
terminal can not be output when the 
projector is in standby mode.
Test Pattern
Use this function to display built-in test pattern when 
installing the projector.
Press ▲▼ to select [Test Pattern].1 ) 
Press ► to display the setting dialog 2 ) 
box.
Press ◄► to switch [On]/[Off].3 ) 
If you want to return the normal mode to the  z
previous image, set [Test Pattern] to [Off] in the 
[Setting] menu.
OnDisplay the built-in Test Pattern.
OffDisable the function. 
						

							Setting
ENGLISH - 39
Settings
Remote ID
When you use the system with multiple projectors, 
you can operate all the projectors simultaneously or 
each projector individually using single remote control, 
if a unique ID number is assigned to each projector.
There are 7 different remote control IDs: [All], 
[ID1]~[ID6].
Press ▲▼ to select [Remote ID].1 ) 
Press ► to display the setting dialog 2 ) 
box.
Press ◄► to select the desired item.3 ) 
Attention
When operating the projector under [All] code, you can  z
operate several projectors at the same time.
If you want to control the projector with a specified  z
remote control ID, make sure the remote control ID on 
the remote control fit to the remote control ID on the 
projector. (Æpage 18)
Startup Logo
Set this function to display the Panasonic logo when 
the projector is turning on.
Press ▲▼ to select [Startup Logo].1 ) 
Press ► to display the setting dialog 2 ) 
box.
Press ◄► to switch [On]/[Off].3 ) 
OnThe logo will display when the 
projector is turning on.
OffThe logo will not display when the 
projector is turning on.
UART Mode
Use this function to select RS-232 or LAN function.
Press ▲▼ to select [UART Mode].1 ) 
Press ► to display the setting dialog 2 ) 
box.
Press ◄► to select the desired item.3 ) 
LANControl the projector via  
terminal.
RS-232Control the projector via  terminal.
Note
When [RS-232] is selected, [LAN(Standby)] and the  z
items of [LAN] are disable.
LAN (Standby)
Use this function to use network function when the 
projector is in standby mode.
Press ▲▼ to select [LAN (Standby)].1 ) 
Press ► to display the setting dialog 2 ) 
box.
Press ◄► to switch [On]/[Off].3 ) 
OnLAN function is available when in 
standby mode.
OffLAN function is unavailable when 
in standby mode.
Reset
Return all data that has been set in the [Setting] menu 
to the factory defaults.
Press ▲▼ to select [Reset].1 ) 
Press ► to display the setting dialog 2 ) 
box.
Press ▲▼ to select [Yes].3 ) 
Press ► to execute.4 ) 
Note
Lamp used time has been set by user in the [Options] z 
menu will not be reset. 
						

							Audio
40 - ENGLISH
Settings
Audio
Select [Audio] from the Main Menu (see “How 
to operate menu” on page 31) and then select 
the item from the Sub Menu.
PT-TW330
Mute
Temporarily turn off the sound.
Press ▲▼ to select [Mute].1 ) 
Press ► to display the setting dialog 2 ) 
box.
Press ◄► to switch [On]/[Off].3 ) 
OnMute.
OffOutput audio.
Press z  button on the remote control 
can also turn on/off the sound.
Volume
Adjust the volume.
Press ▲▼ to select [Volume].1 ) 
Press ► to display the adjustment 2 ) 
dialog box.
Press ◄► to adjust the volume.3 ) 
OperationAdjustmentAdjustment 
range
Press ►.Turn up the volumeMaximum value 32
Press ◄.Turn down the 
volumeMinimum value 0
You can also press the  buttons  z
on the remote control or on the control panel.
In Standby Mode (Audio)
This function is used to switch the output audio signal 
from the  terminal On/Off at 
standby mode.
Press ▲▼ to select [In Standby Mode 1 ) 
(Audio)].
Press ► to display the adjustment 2 ) 
dialog box.
Press ◄► to switch [On]/[Off].3 ) 
On
Output the audio signal from the 
 terminal 
when in Standby mode.
Off
Mute the audio signal from the 
 terminal 
when in Standby mode.
Note
When setting the [In Standby Mode (Audio)] function to  z
[On] and in Standby mode status, the connected audio 
signal to  terminal can be output from the 
 terminal. The audio signal 
output level is fixed and cannot be adjusted.