Panasonic DLP Projector Pt Tw330 Operating Instructions

Setting up
ENGLISH - 21
Getting Started
Calculation formulas for projection distance Q
Any other projection distance can be obtained according to the screen dimensions (m) using the following 
calculations. The calculation result is with the "m" unit. (The calculated distance below may contain a certain 
error.) If the screen dimensions are written as "SD",
For 4*3 aspect ratioFor 16:9 aspect ratioFor 16:10 aspect ratio
Screen height (SH)= SD × 0.6= SD × 0.490= SD × 0.530
Screen width...

Setting up
22 - ENGLISH
Getting Started
Adjusting the Projector's Height
The projector is equipped with elevator feet for adjusting the image hei\
ght.
Extend the adjustable feet by rotating in the direction shown in the below picture and retract by rotating in the op-
posite direction.
Adjustable range
Rear adjustable feet * 
10 mm (0.394")
Adjustable range
Front adjustable feet * 
19 mm (0.748")
The front adjustable feet stretch to its end The rear adjustable feet stretch to its end
2.7 °6...

Connections
ENGLISH - 23
Getting Started
Before connecting to the projector
Read carefully the instruction manual for the device to be connected. z
Turn off the power switch of the devices before connecting cables. z
If any connection cable is not supplied with the device, or if no option\
al cable is available for connection of the  z
device, prepare a necessary system connection cable to suit the device.
Video signals containing too much jitter may cause the images on the scre\
en to randomly wobble or...

Connections
24 - ENGLISH
Getting Started
Connecting example: Computers
Audio equipment
Control
ComputerMonitorComputerComputer
Connecting example: AV equipment
Blu-ray disk 
playerDVD player VCR
(with built-in TBC)Audio equipment 

Powering ON/OFF
ENGLISH - 25
Basic Operation
Powering ON/OFF
Connecting the power cord
Use the supplied power cord to prevent removal of the power cord and mak\
e sure that it is fully 
inserted into the projector.
For detailed power cord handling, refer to “Read this first!” (Æ pages 2 to 6).
Attaching J
Check the shapes of the  terminal on the back side of the project\
or and the 1 ) 
power cord connector and fully insert.
Connect the power plug to an outlet.2 ) 
R
Removing J
Confirm that the projector...

Powering ON/OFF
26 - ENGLISH
Basic Operation
ON(G)/STANDBY(R) indicator
The ON(G)/STANDBY(R) indicator informs you the status of the power. Confirm the status of the  
 indicator before operating the projector.
Indicator statusStatus
No illuminationThe power plug is not connected to the outlet.
Red
Lit*1The power is switched off. (Standby mode)
Press  to start projection.
Slow
Blinking*2The power is switched off. (Standby mode)
Press  to start projection.
BlinkingThe projector is preparing to switch off...

Powering ON/OFF
ENGLISH - 27
Basic Operation
Powering On the Projector
Before switching on the projector, make sure all the other devices are correctly connected (Æpage 24) and 
remove the lens cap.
Connect the power plug to the power outlet.1 ) 
Enter Standby status when the  indicator is lighting / blinking in red. z
Press the  button on the control panel or the remote control.
When the  indicator lights up in green, the lamp is on. z
 Startup screen is displayed for about 10 seconds, then the image...

Projecting
28 - ENGLISH
Basic Operation
Check the connections of the peripheral devices and connection of the power cord (Æpage 25) and switch on the 
power (Æpage 27) to start the projector. Select the image and adjust the state of the image.
Selecting the input signal
Select an input signal.
Press  button on the control panel or the , 
, ,  button on the remote 
control.
The image of the signal being input in the selected terminal is  z
projected.
Press  button to display the [Source] menu. Press   z...

Basic operations by using the remote control
ENGLISH - 29
Basic Operation
Switching the input signal
Press this button to switch input signals.
 Buttons
Press (, , ) 
button on the remote control.
COMPUTERSwitches to Computer 1/
Computer 2 input.
HDMI Switches to HDMI input.
VIDEOSwitches to Video input. 
Note
For details, see “Selecting the input signal”. ( zÆpage 28)
 button
Press this button to display the [Lamp Power Mode] 
menu.
 Button
Press the  button on the remote 
control.
Note
For details, see...

Basic operations by using the remote control
30 - ENGLISH
Basic Operation
 button
Press this button to display the picture mode menu 
and to change the settings of the image.
   Button
Press the  button on the remote 
control.
Note
For details, see [Color Mode] menu of [Picture] menu.  z
(Æpage 34)
 button
Press this button to display the [Input] menu and to 
switch to the desired input signal.
   Button
Press the  button on the remote 
control.
Note
For details, see “Selecting the input signal”. (...