Panasonic DLP Projector PT-DZ780 PT-DW750 PT-DX820 Operating Instructions

Chapter 1 Preparation — Precautions for use
ENGLISH - 21
Early Warning Software
The projector supports “Early Warning Software”, which monitors the status of the display (projector and flat panel 
display) and the peripheral devices inside an intranet, and notifies of abnormality of such equipment and detects 
signs of possible abnormality. Also, maintenance can be performed in advance, because this software gives 
notification of approximate time to replace consumables of the display, to clean each part...

Chapter 1 Preparation — Precautions for use
22 - ENGLISH
 rComputer and external device connections
 fWhen connecting a computer or an external device, read this manual carefully regarding the use of power cords 
and shielded cables as well.
Accessories
Make sure that the following accessories are provided with your projector . Numbers enclosed in <    > show the 
number of accessories.
Wireless/wired remote control unit 
(N2QAYA000060)
Power cord 
(TXFSX03VBDZ)
(TXFSX02VBDZ)
(TXFSX03VARZ)
(TXFSX02UTRZ)...

Chapter 1 Preparation — Precautions for use
ENGLISH - 23
Contents of the supplied CD-ROM
The contents of the supplied CD-ROM are as follows.
Instruction/list (PDF) Operating Instructions – Functional ManualMulti Projector Monitoring & Control Software Operating Instructions
Logo Transfer Software Operating Instructions
List of Compatible Projector 
ModelsThis is a list of projectors that are compatible with the software 
contained in the CD-ROM and their restrictions.
Software Multi Projector Monitoring...

Chapter 1 Preparation — About your projector
24 - ENGLISH
About your projector
Remote control
1
3 2
4
5
7 6
8
9
10 15 12 11
13
14 16
17
Front To p
Bottom
1 Power standby  button
Sets the projector to the state where the projector is switched 
off (standby mode) when the  switch on the 
projector is set to  and in projection mode.
2
 
Power on < b

> button
Starts projection when the  switch on the 
projector is set to  when the power is switched off 
(standby mode).
3
 
Remote control indicator
Blinks if...

Chapter 1 Preparation — About your projector
ENGLISH - 25
 fThe operation of the  button is disabled in the factory default settings.  The operation is enabled when [REMOTE CONTROL] is set 
to [USER] and [VIDEO BUTT ON] of [INPUT SELECT BUTTON] is set to other than [DISABLE], from the [SECURITY] menu  → [CONTROL 
DEVICE SETUP] (x
  page   135).
Projector body
1 2 3 4 5 6
7 7
10
12
8
17 18
14
13 15
1611
914 14
Front Side
Rear
141414
141414
19
Projection direction
Bottom
Warning
Keep your hands and other...

Chapter 1 Preparation — About your projector
26 - ENGLISH
Attention
 fDo not block the ventilation ports (intake and exhaust) of the projector .
 rControl panel
9
10
11
12
13
14
2
4 3 1
5
6
7
8
1 Power on <
b > button
Starts projection when the  switch on the 
projector is set to  when the power is switched off 
(standby mode).
2
 
Power standby <
 v> button
Sets the projector to the state where the projector is switched 
off (standby mode) when the  switch on the 
projector is set to  and in projection...

Chapter 1 Preparation — About your projector
ENGLISH - 27
 rConnecting terminals
1 25
3 4
6 78 911
10
1  terminal/ terminal
These are the terminals to connect the remote control for serial 
control in a multiple projector environment.
2
 
 terminal
This is a terminal to remotely control the projector using the 
external control circuit.
3

 
 terminal
This is the RS
- 232C compatible terminal to externally control 
the projector by connecting a computer.
4
 
 terminal
This is a terminal to output the...

Chapter 1 Preparation — Preparing the remote control
28 - ENGLISH
Preparing the remote control
Inserting and removing the batteries
ii)i)
Fig. 1Fig. 2
1) Open the cover. (Fig. 1)
2)  
Insert the batteries and close the cover (insert the 
 m side first). (Fig. 2)
 fWhen removing the batteries, perform the steps in reverse order

.
When using the multiple projectors
When you use the multiple projectors together, you can control all the projectors simultaneously or each projector 
individually using single...

Chapter 1 Preparation — Preparing the remote control
ENGLISH - 29
Connecting the remote control to the projector with a cable
When you use the system with multiple projectors, use commercially available M3 stereo mini jack cables and 
connect the other devices to the / terminals of the projector.
The remote control is effective even in places where an obstacle stands in the light path or whe\
re devices are 
susceptible to outside light.
Connecting terminals Connecting to a second projector
M3 stereo...

30 - ENGLISH
Chapter 2 Getting Started
This chapter describes things you need to do before using the projector \
such as the setup and connections.