Panasonic DLP Projector PT-DZ770U PT-DZ770UL Operating Instructions

							Technical information
ENGLISH - 121
Appendix
ModeResolution
(Dots) Scanning 
frequency
Dots
clock
Frequency (MHz)
Format*3Plug and play*4
Horizontal (kHz)Vertical(Hz) RGB2DVI-D
EDID1 DVI-D
EDID2 DVI-D
EDID3 HDMI
MXGA 1 152 x 864 64.0 70.0 94.2 R/H/D
― ― ― ― ―
1 152 x 864 67.5 74.9 108.0 R/H/D― ― ― ― ―
1 152 x 864 77.1 85.0 119.7 R/H/D― ― ― ― ―
MAC21
1 152 x 870 68.7 75.1 100.0 R/H/D3―
3 3 3
1280 x 768 1 280 x 768 39.6 49.9 65.3 R/H/D― ― ― ― ―
1 280 x 768 47.8 59.9 79.5 R/H/D― ― ― ― ―
1280 x 8001 280 x 800 41.3 50.0 68.0 R/H/D― ― ― ― ―
1 280 x 800 49.7 59.8 83.5 R/H/D― ― ― ― ―
MSXGA
1 280 x 960 60.0 60.0 108.0 R/H/D― ― ― ― ―
SXGA1 280 x 1 024 64.0 60.0 108.0 R/H/D
3
―
3 3 3
1 280 x 1 024 80.0 75.0 135.0 R/H/D3―
3 3 3
1 280 x 1 024 91.1 85.0 157.5 R/H/D― ― ― ― ―
SXGA+ 1 400 x 1 050 65.2 60.0 122.6 R/H/D3
―
3 3 3
1 400 x 1 050 82.2 75.0 155.9 R/H/D― ― ― ― ―
WXGA+ 1 440 x 900 55.9 59.9 106.5 R/H/D― ― ― ― ―
UXGA1 600 x 1 200 75.0 60.0 162.0 R/H/D3―
3 3 3
WSXGA+ 1 680 x 1 050 65.3 60.0 146.3 R/H/D― ― ― ― ―
1920 x 1080 1 920 x 1 080*266.6 59.9 138.5 R/H/D― ― ― ― ―
WUXGA1 920 x 1 200*274.0 60.0 154.0 R/H/D3―
3 3 3
*1: When a 1 125 (1035)/60i signal was input, it is displayed as a 1125 (1080)/60i signal.
*2:  VESA  CVT-RB (Reduced Blanking) compatible
*3:
 
Signals that show formats are as follows.
V : Video
S 
: S video
D

 
: DVI-D
R

 
: RGB
Y
 : 

YC
BCR/YPBPR
H : HDMI*4: Signals with a  3 in the Plug and Play columns are signals described 
in the projector’s EDID (extended display identification 
data). If a signal has no  3 in the Plug and play columns but has an entry in the Format column, it can be entered. For signals 
without a  3 in the Plug and play columns, there are instances where resolution cannot be selected in the computer even though 
the projector supports them.
Note
 z There are 1 920 x 1 200 display dots for PT

-DZ770U. A signal with a different resolution is converted to the 
number of display dots and displayed.
 z The “i”  at the end of the resolution indicates an interlaced signal.
 zWhen interlaced signals are connected, flickering may occur on the projected image. 
						

							Specifications
122 - ENGLISH
Appendix
The following table describes the specifications of the projector.
Model No.PT-DZ770U PT-DZ770UL
Power supply AC 120 V  50 Hz/60 Hz
Power consumption 830 W (8 A)
(0.2 W when [STANDBY MODE] is set to [ECO], and 6 W when set to [NORMAL])
DLP 
chips Panel size
0.67" (aspect ratio 16:10)
Display method 1-unit DLP chips, DLP type
Number of pixels 2 304 000 pixels
(1 920 x 1 200 dots)
Lens Power zoom
1.7 to 2.4:1
Optional
Power focus F = 1.7 to 1.9
f = 25.6 mm to 35.7 mm
Luminous lamp 300 W (maximum 310 W)  UHM lamp x 2
Light output 7 000 lm 
*1 (ANSI)
Measure 
Scanning 
Frequency
For video signals
(including S 
video)Horizontal: 15.75 kHz/15.63 kHz, Vertical: 50 Hz/60 Hz
For RGB signals Horizontal: 15 kHz to 91 kHz, Vertical: 50 Hz to 85 Hz
PIAS (Panasonic Intelligent Auto Scanning) system
Dot clock frequency162 MHz or less
For YC
BCR/
YP
BPR signals 525i (480i): 
Horizontal: 15.75 kHz, Vertical: 60 Hz
525p (480p): 
Horizontal: 31.5 kHz, Vertical: 60 Hz
750 (720)/60p: 
Horizontal: 45 kHz, Vertical: 60 Hz
1125 (1035)/60i: 
Horizontal: 33.75 kHz, Vertical: 60 Hz
1125 (1080)/50i: 
Horizontal: 28.13 kHz, Vertical: 50 Hz
1125 (1080)/24sF: 
Horizontal: 27 kHz, Vertical: 48 Hz
1125 (1080)/30p: 
Horizontal: 33.75 kHz, Vertical: 30 Hz
1125 (1080)/50p: 
Horizontal: 56.25 kHz, Vertical: 50 Hz 625i (576i): 
Horizontal: 15.63 kHz, Vertical: 50 Hz
625p (576p): 
Horizontal: 31.25 kHz, Vertical: 50 Hz
750 (720)/50p: 
Horizontal: 37.5 kHz, Vertical: 50 Hz
1125 (1080)/60i: 
Horizontal: 33.75 kHz, Vertical: 60 Hz
1125 (1080)/24p: 
Horizontal: 27 kHz, Vertical: 24 Hz
1125 (1080)/25p: 
Horizontal: 28.13 kHz, Vertical: 25 Hz
1125 (1080)/60p: 
Horizontal: 67.5 kHz, Vertical: 60 Hz
 z
The SYNC/HD and VD terminals do not support 3 value SYNC.
For DVI-D signal 525p (480p), 625p (576p), 750 (720)/60p, 750 (720)/50p,
1

125 (1080)/60i, 1125 (1080)/50i, 1125 (1080)/24p, 1125 (1080)/24sF, 1125 (1080)/25p, 
1125 (1080)/30p, 1125 (1080)/60p, 1125 (1080)/50p
 z Displayable resolution: VGA

 to WUXGA (non-interlaced)
 zDot clock frequency: 25 MHz to 162 MHz zWUXGA

 signal supports only VESA CVT-RB (Reduced Blanking) signal.
For HDMI signal 525p (480p), 625p (576p), 750 (720)/60p, 750 (720)/50p,
1125 (1080)/60i, 1125 (1080)/50i, 1125 (1080)/24p, 1125 (1080)/24sF, 1125 (1080)/25p, 
1125 (1080)/30p, 1125 (1080)/60p, 1125 (1080)/50p
 z
Displayable resolution: VGA

 to WUXGA (non-interlaced)
 zDot clock frequency: 25 MHz to 162 MHz
Color system 7 standards (NTSC/NTSC4.43/P

AL/PAL-N/PAL-M/SECAM/PAL60)
Projection screen size 1.27 m (50") - 15.24 m (600")
*2
Screen aspect ratio 16:10
Projection method [FRONT/CEILING], [FRONT/FLOOR], [REAR/CEILING], [REAR/FLOOR]
Contrast ratio 2 500:1
(when [CONTRAST MODE] is [HIGH])
Specifications 
						

							Specifications
ENGLISH - 123
Appendix
Model No.PT-DZ770U PT-DZ770UL
Terminals
 
terminal1 set (BNC x 5)
RGB signals
0.7 V [p-p] 75 Ω (SYNC ON GREEN: 1.0 V [p-p] 75 Ω)SYNC/HD TTL high impedance, automatic positive/negative polarity compatibleVD TTL high impedance, automatic positive/negative polarity compatible
YP
BPR signals Y: 1.0 V [p-p] including synchronization signal, PBPR: 0.7 V [p-p] 75 Ω
 
terminal 1 set, high-density D-Sub 15p (female)
RGB signals
0.7 V [p-p] 75 Ω (SYNC ON GREEN: 1.0 V [p-p] 75 Ω)
SYNC/HD TTL high impedance, automatic positive/negative polarity compatibleVD TTL high impedance, automatic positive/negative polarity compatible
YP
BPR signals Y: 1.0 V [p-p] including synchronization signal, PBPR: 0.7 V [p-p] 75 Ω
 terminal1 set, DVI-D 24 p single link, DVI 1.0 compatible, HDCP compliant
 terminal1 set, HDMI 19 pin, (HDCP and Deep color compatible)
 terminal1 set, BNC 1.0 V [p-p] 75 Ω
 terminal1 set, Mini DIN 4 p Y 1.0 V [p-p], C 0.286 V [p-p] 75 Ω S1 signal compatible
/ 
 
terminal D-Sub 9 p, each set, RS-232C compatible, for computer control
/ 
 terminalM3 stereo mini jack, each set for remote control (wired)/for projector serial control
 
terminal 1 set D-Sub 9 p (female) for contact control
 terminal 1 set, (for RJ-45 network connection, PJLink compatible, 10Base-T/100Base-TX)
Power cable length 3.0 m (118-1/8")
Outer case Molded plastic
Dimensions Width: 498 mm (19-19/32")
Height: 175 mm (6-7/8")
(with minimum feet length)
Depth: 466 mm (18-11/32")
(including the standard zoom lens) Width: 498 mm (19-19/32")
Height: 175 mm (6-7/8")
(with minimum feet length)
Depth: 423 mm (16-21/32")
Weight Approx 16.3 k
g
 (35.9 lbs.)
*3
(including the standard zoom lens) Approx 15.4 k
g
 (34 lbs.)*3
Operating environment Operating environment temperature*4: 0°C (32°F) to 45°C (113°F)
Operating environment humidity: 20% to 80% (no condensation)
Remote 
control Power supply
DC 3 V (AA/R6 battery x 2)
Operating range Within 30 m (98'5") (when operated directly in front of signal receiver)
Weight 134 g
 (4.7 ozs.)(including batteries)
Dimensions Width: 51 mm (2")  Height: 176 mm (6-15/16")  Depth: 22.7 mm (29/32")
*1:
 
V

alue for the supplied standard zoom lens. The value varies depending on the lens. The indicated value is an average value 
of the overall projector at factory default, and is written in accordance with the specification form of the JIS X 691 1:2003 data 
projector. Measurement methods and measuring conditions comply with Appendix 2.
*2:
 
The size is maximum 200" when ET

-DLE055 lens is used.
*3:
 
A

verage value. Weight varies for each product.
*4:
 
When using the projector at high altitudes (1 400 m (4 593 ft) – 2 700 m (8 858 ft) above sea level), the operating environment 
temperature will be 5°C (41°F) lower than the maximum limit. In addition, when the projector is used with the following two 
settings, if the ambient temperature exceeds 40°C (104°F) (35°C (95°F) in [HIGH  AL

TITUDE MODE]), light output is sometimes 
reduced by 20% to protect the projector. –
 
When [LAMP

 SELECT] is set to [DUAL] in the menu
–
 
When [LAMP

 POWER] is set to [NORMAL] in the menu
 z The model numbers of accessories and optional components are subject to change without notice. 
						

							Dimensions
124 - ENGLISH
Appendix
Dimensions
 zWhen installing the projector to a ceiling, be sure to use the specified ceiling mount bracket (ET
-PKD56H: for 
high ceilings, ET -PKD55S: for low ceilings).
 zWhen installing the projector

, attach the drop-prevention set included with the ceiling mount bracket to the 
projector.
If you need the drop-prevention set (Product No. TTRA0214) separately, consult your dealer.
 z Request for a qualified technician to do the installation.
 zT

akes no responsibility for any damage to the projector resulting from use of a ceiling mount bracket not 
manufactured by Panasonic or the inappropriate choice of location for installation, even if the warranty period 
of the projector has not expired.
 z Unused products must be removed promptly by a qualified technician.
 zUse a torque screwdriver or 

Allen torque wrench to tighten bolts to their specified tightening torques. Do not 
use tools such as electric screwdrivers or impact screwdrivers.
 z For details, read the installation manual that comes with the ceiling mount bracket.
 zThe model numbers of accessories and optional components are subject to change without notice.
M6
12 mm (15/32)
Bottom view
Mo\fel No. o\b ceiling\w mount bracket: ET-PKD56H (\bor high\w ceilings)
ET-PKD55S (\bor low \wceilings)
Torque: 4± 0.5 N·m
Ceiling mount bracket safeguards
498 (19-19/32")
77.5 (3-1/16") 22 (25/32")
21 (13/16")
9 (11/32")
5 (3/16")
155 (6-3/32") 43 (1-11/16") 423 (16-21/32")
Units: mm
* The above shows the dimensions with the standard zoom lens attached.
*  
Actual dimensions may dif
 fer depending on the product. 
						

							Index
ENGLISH - 125
Appendix
Index
AAccessories ……………………………………… 18
 terminal  …………………………… 22,   37
Adjusting adjustable feet
 ………………………… 31
[ADV

ANCED MENU]  
……………………… 47,
   56
[AI]
 ………………………………………………… 52
Air filter unit

 
………………………………………106
Air filter unit compartment ………………………107
[ASPECT]

 
………………………………………… 53
 button Remote control
 ………………………… 21,

  45
Aspect function
 
…………………………………… 45
[AUT

O SETUP]
 …………………………………… 62
 button
Projector body
 ………………………… 23,

  44
Remote control
 ………………………… 21,

  44
Auto setup function
 
……………………………… 44
[AUT

O SIGNAL]
 ………………………………… 62
B[BACK COLOR] ………………………………… 65
[BLANKING]  ……………………………………… 56
[BRIGHTNESS]
 
………………………………… 49
CCautions on use ………………………………… 17
Cautions when transporting …………………… 14
Ceiling mount bracket ……………………………124
Ceiling mount bracket safeguards ………………124
[CLAMP

 POSITION]
 …………………………… 57
[CLOCK PHASE]

 
………………………………… 55
[COLOR]

 
………………………………………… 50
[COLOR CORRECTION]

 
……………………… 61
[COLOR MA

TCHING]  
…………………………… 60
[COLOR 

TEMPERATURE]  
……………………… 50
Connecting the power cord ……………………… 37
Connection ……………………………………… 34
[CONTRAST]

 
…………………………………… 49
[CONTRAST

 MODE]  
…………………………… 61
[CONTROL

 DEVICE SETUP]  
………………… 82
[COOLING CONDITION] ……………………… 69
CRESTRON RoomV

iew  
…………………… 85,
   102
[CUT OFF]
 ………………………………………… 67
D[DATE AND TIME] ……………………………… 75
 button
Remote control
 ………………………… 21,

  46
Deleting the registered data
 …………………… 78
[DIGIT

AL CINEMA REALITY]  
…………………… 56
Dimensions ………………………………………124
Direct Power Of

f Function  
……………………… 40
Display language …………………………… 48,

  59
[DISPLAY OPTION]
 ………………………… 48,

  60
[DISPLAY SETTING]
 …………………………… 81
Disposal …………………………………………… 16
 button Projector body
 ………………………… 23,

  43
Remote control
 ………………………… 21,

  43
[DVI-D IN]
 
………………………………………… 63
E[EDGE BLENDING] ……………………………… 57
 button Projector body
 ……………………………… 23
Remote control ……………………………… 21
Expanding signal lock-in range ………………… 79
FFilter indicator ……………………………………105
 button Remote control
 ………………………… 21,

  41
[FREEZE]
 ………………………………………… 66
Function button ……………………………… 44,

  75
 button Remote control
 ………………………… 21,

  44
H buttonProjector body ………………………… 23,   43
Remote control
 ………………………… 21,

  43
[HDMI IN]
 
………………………………………… 64
[HIGH 

ALTITUDE MODE]
 ……………………… 69
I buttonRemote control ………………………… 21,   24
 button
Remote control
 ………………………… 21,

  24
[INITIALIZE]
 ……………………………………… 76
Initial setting ……………………………………… 20
[INPUT

 RESOLUTION]  
………………………… 57
Installation precautions ………………………… 14
K[KEYSTONE] ……………………………………… 55
LLamp indicator ……………………………………104
[LAMP  POWER] ………………………………… 70
[LAMP
 RELAY]  
…………………………………… 70
[LAMP

 SELECT]  
………………………………… 69
Lamp unit cover ………………………………… 22
 button Projector body
 ………………………… 23,

  41
List of compatible signals
 ………………………120
[LOAD 

ALL USER DATA]  
……………………… 76
MMain menu ………………………………………… 47
Main power switch ………………………… 22,   39
Maintenance
 ………………………………………106
Managing the sub memory list ………………… 80
 button Projector body
 ………………………… 23,

  46
Remote control
 ………………………… 21,

  46
Menu item
 
………………………………………… 47
[MENU LOCK]

 
…………………………………… 82
[MENU LOCK P

ASSWORD]  
…………………… 82
NNavigating through the menu …………………… 46
[NETWORK] ………………………………… 48,   84
Network connections
 …………………………… 85
[NETWORK CONTROL] ………………………… 84
[NETWORK SETUP] …………………………… 84
[NETWORK ST

ATUS]  
…………………………… 84
[NOISE REDUCTION]

 
…………………………… 51
[NO SIGNAL

 SHUT-OFF]
 ……………………… 75
O buttonRemote control ………………………… 21,   43
[ON-SCREEN DISPLAY]
 
………………………… 64
On-screen menu ………………………………… 46
Optional accessories …………………………… 19
P[PICTURE] …………………………………… 47,   49
[PICTURE MODE]  ……………………………… 49
[POSITION] ………………………………… 47,

  53
Power cord
 ……………………………………… 37
Power indicator …………………………………… 38
Power on button Projector body
 ……………………………… 23
Remote control ……………………………… 21
Power standby button
Projector body
 ……………………………… 23
Remote control ……………………………… 21
Precautions for Use ……………………………… 14
Projecting ………………………………………… 41
[PROJECTION METHOD] ………………… 25,

  68
Projector body
 …………………………………… 22
[PROJECT

OR ID]  
………………………………… 68
[PROJECT

OR SETUP]  
…………………… 48,
   68
Protecting the registered data
 ………………… 79
R[RASTER POSITION] …………………………… 58
Read this first!  ……………………………………… 2
Registering a signal to the list ………………… 78
 terminal

 
……………………… 24
 terminal

 
…………………… 24
 terminal

 
……………………… 1
 18
[REMOTE2 MODE]
 ……………………………… 73
Remote control …………………………………… 21
Remote control operations ……………………… 43 Removing/attaching a projection lens
 ………… 32
Renaming the registered data ………………… 78
Replacing the air filter unit ………………………107
Replacing the lamp unit …………………………108
Replacing the unit…………………………………107
Resetting to the factory default

 
………………… 46
 button Projector body
 ………………………… 23,

  43
Remote control
 ………………………… 21,

  43
 button
Projector body
 ………………………… 23,

  43
Remote control
 ………………………… 21,

  43
[RGB IN]…………………………………………… 63
RoomView
 
…………………………………………102
[RS-232C]

 
…………………………………… 72,
   115
S[SAVE ALL USER DATA] ………………………… 76
[SCHEDULE]……………………………………… 71
[SCREEN SETTING]
 …………………………… 62
Security

 
…………………………………………… 16
[SECURITY]

 
………………………………… 48,
   81
[SECURITY PASSWORD]
 
……………………… 81
[SECURITY

 PASSWORD CHANGE]  
………… 81
Selecting the input signal ……………………… 41
 terminal  
…………………………… 1
 15
 terminal
 
………………………… 1
 15
[SERVICE PASSWORD]
 
………………………… 76
Setting remote control ID numbers …………… 24
Setting up

 
………………………………………… 25
[SHARPNESS]

 
…………………………………… 51
[SHIFT] …………………………………………… 53
 button Remote control
 ………………………… 21,

  41
 button
Projector body
 ………………………… 23,

  43
Remote control
 ………………………… 21,

  43
[SHUTTER SETTING]
 …………………………… 66
[SIDE BY

 SIDE]  
…………………………… 66,
   119
[SIGNAL LIST]
 ……………………………… 48,

  78
Specifications
 ……………………………………122
[ST

ANDBY MODE]  
……………………………… 70
[ST

ARTUP INPUT SELECT]  
…………………… 72
[ST

ARTUP LOGO]
 ……………………………… 65
[ST

ATUS]  
………………………………………… 74
 button
Remote control
 ………………………… 21,

  43
 button
Projector body
 ………………………… 23,

  43
Remote control
 ………………………… 21,

  43
Switching off the projector
 
……………………… 40
Switching the input signal ……………………… 43
Switch on the projector

.  
………………………… 39
[SYSTEM DA

YLIGHT VIEW]
 …………………… 51
[SYSTEM SELECT

OR]  
………………………… 52
TTemperature indicator ……………………………105
[TEST  PATTERN]  …………………………… 48,   77
 button Remote control
 ………………………… 21,

  44
[TEXT CHANGE]
 
………………………………… 82
[TINT] ……………………………………………… 50
T

roubleshooting
 ………………………………… 1
 10
V buttonProjector body ………………………… 23,   43
Remote control
 ………………………… 21,

  43
W[WHITE GAIN] …………………………………… 51
Z[ZOOM] …………………………………………… 54
 button Remote control
 ………………………… 21,

  41 
						

							W0612NN1062 -YI
Environment care information for users in China
This symbol is only valid in China. 
Information on Disposal in other Countries outside the European Union
These symbols are only valid in the European Union.
If you wish to discard this product, please contact your local authorities or dealer and ask for 
the correct method of disposal.
Panasonic System C\rommunications Comp\rany of Nort\f America\r
One Panasonic Way \S2F-13, Seca\fc\fs, NJ \S0\b094
TEL: (8\b\b) 803 - 8492
Panasonic Canada In\rc\b
5\b\b0 Ambler Drive, M\Sississa\fga, Ontario\S L4W 2T3
TEL: (905) 624 - 50\S10
0ñ1111111
10Á0ä11111111
11
Web Site : http://panasonic.net/avc/projector/
© Panasonic Corporation 2012