Panasonic DLP Projector PT-DZ680U PT-DZ680UL Operating Instructions

ENGLISH - 41
Chapter 3 Basic Operation — Switching on/off the projector
or higher, turn off the main power, and then turn on the power again.
r
f If the [PROJECTOR SETUP] menu 
→ [STANDBY MODE] (
x page 76) is set to [ECO], there may be a time lag of approximately 10 
seconds between turning on the power and starting projection compared to when the setting is [NORMAL].
r
f If the  switch was turned  during projection the last time that the direct power of
f function was used, and the  switch is turned...

42 - ENGLISH
Chapter 3 Basic Operation — Switching on/off the projector
3) Wait until the power indicator  of the projector lights in red (and 
the fan stops) for approximately 170 seconds.4) Press the  side of the  
switch to turn off the power.
Note
r
f Do not turn on the power and project images immediately after turning th\
e projector off.
Turning on the power while the lamp is still hot may shorten the lamp life.
r
f The lamp indicators will not light on for about 75 seconds after the projector is...

ENGLISH - 43
Chapter 3 Basic Operation — Projecting
Projecting
Check the projection lens attachment (
x page 33), external device connection (
x page 35) and power cord connection (
x page 39), 
and then switch on the power ( x page 40) to start projecting. Select the video for projection, and adjust ap\
pearance of the projected image.
Selecting the input signal
Select an input signal.
1) Press the input selection (, , 
, , , ) 
buttons on the control panel or the remote 
control.
r
f The image of the...

44 - ENGLISH
Chapter 3 Basic Operation — Projecting
Moving the lens to the home position
Perform the following procedure to move the lens to the home position.
1) Press the  button on the control panel 
or the  button on the remote control 
for at least three seconds.2) While the [HOME POSITION] menu is displayed 
(for approximately five seconds), press the 
 button.
MENUENTER
LENS
HOME POSITION
CANCELEXECUTE
r
f [PROGRESS] is displayed in the menu screen, and the lens 
returns to the home position....

ENGLISH - 45
Chapter 3 Basic Operation — Remote control operation
Remote control operation
Using the shutter function
If the projector is not used for a certain period of time during the meeting intermission, for example, it is possible to turn of f the image 
temporarily.
 button
1) 
Press the  button.
r
f The image disappears.
r
f This operation can be also performed using the  
button on the control panel.
2) Press the  button again.
r
f The image is displayed.
Note
r
f The power indicator  will flash...

46 - ENGLISH
Chapter 3 Basic Operation — Remote control operation
Switching the input
The input for projection can be switched.
 button
1) 
Press the input selection (, , 
, , , and ) 
buttons.
r
f This operation can be also performed by pressing the input 
selection (, , , , , 
and ) buttons on the control panel.
r
r Switching the input items

Switches to RGB1 input.
 Switches to RGB2 input.
 Switches to DVI-D input.
 Switches to VIDEO input.
 Switches to S-VIDEO input.
 Switches to HDMI input.
Using...

ENGLISH - 47
Chapter 3 Basic Operation — Remote control operation
1) Press the  button.
r
f [COMPLETE] is displayed when it has completed without any 
problem.
r
f This operation can be also performed using the  button on the control panel.
Note
r
f The CLOCK PHASE may shift even if it has completed without any incident. In such cases, adjust with the [POSITION] menu 
→ [CLOCK 
PHASE] ( x page 60).
r
f If an image with blurred edges or a dark image is input, [INCOMPLETE] may appear or adjustment may not...

48 - ENGLISH
Chapter 4 Settings
This chapter describes the settings and adjustments you can make using t\
he on-screen menu.  

ENGLISH - 49
Chapter 4 Settings — Menu navigation
Menu navigation
The on-screen menu (Menu) is used to perform various settings and adjustments of the projector .
Navigating through the menu
Operating procedure
 button
1) 
Press the  button on the remote 
control or the control panel.
r
f The 
[MAIN MENU]  screen is displayed.
(17(5
0$,10(18
3,&785(
326,7,21
$9 $1&(0(18
,63/$ 

50 - ENGLISH
Chapter 4 Settings — Menu navigation
1) Press the  button on the remote 
control.

&2175$67
$-867
Note
r
f You cannot reset all the settings to the factory default at once.
r
f To reset all the settings adjusted in the sub-menu item to the factory default at a time, perform initialization from the [PROJECTOR SETUP] 
menu 
→ [INITIALIZE] (
x page 82).
r
f Some menu items cannot be reset by pressing the  button. Adjust each item manually.
r
f The triangular mark under the bar scale in the...