Panasonic DLP Projector PT-DZ21KU PT-DS20KU PT-DW17KU Operating Instructions

							[DISPLAY LANGUAGE] menu
ENGLISH - 81
Settings
Select [DISPLAY LANGUAGE] from the main 
menu, and display the sub-menu.
Refer to “Navigating through the menu” 
(
 page 61) for the operation of the menu 
screen.
 z Press 
▲▼ to select a language, and press the 
 button to set.
Changing the display 
language
You can select the language of the on-screen display.
ENTER
DISPLAY LANGUAGE
SELECT
SET
 zVarious menus, settings, adjustment screens, 
control button names, etc., are displayed in the 
selected language.
 z The language can be changed to English, German, 
French, Spanish, Italian, Portuguese, Japanese, 
Chinese, Russian, and Korean.
Note
 z The on-screen display language of the projector is 
set to English by default. (Factory default)
[DISPLAY LANGUAGE] menu 
						

							[3D SETTINGS] menu (PT-DZ21KU and PT- DS20KU only)
82 - ENGLISH
Settings
[3D SETTINGS] menu (PT-DZ21KU and PT- DS20KU only)
Select [3D SETTINGS] from the main menu, and 
select the item from the sub-menu.
Refer to “Navigating through the menu ” 
(
 page 61) for the operation of the menu screen.
 z After selecting the item, press 
▲▼◀▶ to set.
[3D SYSTEM SETTING]
Set a picture display method for use during 3D signal 
input as necessary for the 3D system in use.
1) Press 
▲▼ to select [3D SYSTEM 
SETTING].
2)
 
Press  ◀▶ to switch [3D SYSTEM 
SETTING].
▶z The setting will change as follows each time 
you press the button.
[SINGLE][DUAL (LEFT)][DUAL (RIGHT)]
[SINGLE] During 3D signal input, sequential 
frames of images for the right eye 
and images for the left eye are
alternately displayed.
[DUAL 
(LEFT)] Only images for the left eye are 
displayed during 3D signal input.
[DUAL 
(RIGHT)] Only images for the right eye are 
displayed during 3D signal input.
Note
 z When 2D images are input, 2D images are 
displayed regardless of [3D SYSTEM SETTING] 
settings.
[3D SYNC SETTING]
Set the way in which the  
terminal and the  terminal will be 
used.
Attention
 z Before connecting the external device with the 
cables to the  terminal and 
the  terminal, finish the [3D 
S

YNC MODE] setting and confirm that the device is 
turned off.
 z Changing [3D SYNC MODE] while connecting the 
c

ables may result in malfunctions of the projector or 
external devices connected.
1) Press  ▲▼ to select [3D SYNC 
SETTING].
2)
 
Press the  button.
▶z The precaution message related to 3D SYNC 
setting is displayed.
3) Press the  button.
▶zThe  [3D SYNC SETTING] screen is displayed.
4) Press 
▲▼ to select [3D SYNC MODE].
5)  
Press  ◀▶ to switch [3D SYNC MODE].
▶z
The setting will change as follows each time 
you press the button.
[OFF][1]
[11]
[2]
[10] [3]
[9][4]
[8][5]
[7][6]
▶zItems set in [3D SYNC1]
[OFF]
Not used.
[1] 3D trigger output
[2] 3D trigger output
[3] Stereo synch input
[4] Stereo synch input
[5] Stereo synch input
[6] Frame synch input
[7] Frame synch input
[8] Frame synch input
[9] 3D trigger output
[10] Stereo synch output
[11] 3D IR TRANSMITTER (+) output 
						

							[3D SETTINGS] menu (PT-DZ21KU and PT- DS20KU only)
ENGLISH - 83
Settings
▶zItems set in [3D SYNC2]
[OFF]
Not used.
[1] Stereo synch output
[2] 3D trigger output
[3] Through 3D SYNC1
[4] Stereo synch output
[5] 3D trigger output
[6] Through 3D SYNC1
[7] Stereo synch output
[8] 3D trigger output
[9] Frame synch output
[10] Frame synch output
[11] 3D IR TRANSMITTER (–) output
6) If you selected [1], [4], [7], or [10], 
press 
▲▼ to select [STEREO SYNC 
OUTPUT DELA
Y] and press ◀▶ to set 
the amount of delay output.
▶z Values in the following range change by units of 
10 us.
0 us to 25 000 us
▶z T

o synchronize multiple projectors to display 3D 
images, use a frame synch input and output.
Select [9] or [10] for the first projector.
Select [6], [7], or [8] for the second and 
subsequent projectors.
▶z Stereo synch is a Duty 50% signal at High 
during Left and at Low during Right.
▶zAn “H” is output to the 3D images display and 
an “L” is output to the 2D image display from 
the terminal for which 3D trigger output is 
selected.
Note
 z [1

1] of [3D SYNC SETTING] is the setting when 
the 3D IR Transmitter TY-3DTRW (Panasonic) is 
used with this projector. As for connecting method, 
consult your dealer.
[3D SIMUL INPUT SETTING]
Set to input and use simultaneous 3D images signals.
1) Press  ▲▼ to select [3D SIMUL
 INPUT 
SETTING].
2)
 
Press the  button.
▶z The  [3D SIMUL INPUT SETTING]
 screen is 
displayed.
3) Press  ▲▼ to select [LEFT
:RGB1 
RIGHT:RGB2], [LEFT:HDMI 
RIGHT:DVI-D], or [LEFT:SDI1 
RIGHT:SDI2].
4)
 
Press  ◀▶ to switch the setting.
▶z
The setting will change as follows each time 
you press the button.
[OFF][AUTO]
[OFF]
Cannot use 3D simultaneous.
[AUTO] Displays simultaneous 3D images.
Note
 z When set to [AUT

O], 3D images are displayed 
when the same 3D compatible signals are entered 
to each input. However, the P IN P status during P 
IN P is maintained.
 z This may not function properly for some external 
devices that are connected.
 zCertain signals may not function properly

. 
						

							[3D SETTINGS] menu (PT-DZ21KU and PT- DS20KU only)
84 - ENGLISH
Settings
[3D INPUT FORMAT]
Set the 3D format for the image signals being input. 
Set a 3D format that matches the input signal.
1) Press 
▲▼ to select [3D INPUT 
FORMA T].
2)
 
Press the  button.
▶z The  [3D INPUT FORMAT] screen is displayed.
3) Press 
▲▼ to select a 3D format.
4)  
Press the  button.
[AUTO]*1Automatically detects 3D format of 
input image signals and displays 
images.
[NATIVE] Forcibly displays images in 2D 
regardless of input image signals.
[SIMULTANEOUS]*2Forcibly displays 3D images in 
simultaneous format regardless of 
input image signals.
[SIDE BY  SIDE] Forcibly displays 3D images in side 
by side format regardless of input 
image signals.
[TOP AND  BOTTOM] Forcibly displays 3D images in top 
and bottom format regardless of 
input image signals.
[LINE BY  LINE]
*3
Forcibly displays 3D images in line 
by line format regardless of input 
image signals.
[FRAME 
SEQUENTIAL]*4
Forcibly displays 3D images in frame 
sequential format regardless of input 
image signals.
*1: During DVI-D or HDMI input only
*2:  During 3G-SDI level B input only
*3:
 
During signals other than interlaced signals are input
*4:

 
During RGB1, RGB2, DVI-D, and HDMI input only
Note
 zWhen set to [AUT

O], [SIMULTANEOUS], [SIDE BY 
SIDE], [TOP AND BOTTOM], [LINE BY LINE], or 
[FRAME SEQUENTIAL], images are not displayed 
in 3D as per the [3D SIMUL INPUT SETTING]. 
However, this only occurs in [AUTO] when 3D 
format can be recognized.
 z This may not function properly for some external 
devices that are connected.
[LEFT/RIGHT SWAP]
Flips the timing of the switch between the left and 
right of an image to display. Change the setting if the 
3D images you see appear strange.
1) Press 
▲▼ to select [LEFT/RIGHT 
SW AP].
2)
 
Press  ◀▶ to switch [LEFT/RIGHT 
SW

AP].
▶zThe setting will change as follows each time 
you press the button.
[NORMAL][SWAPPED]
[NORMAL] If the 3D images are displayed 
correctly, do not change the 
[NORMAL] settings.
[SWAPPED] Select when left and right 3D 
images are swapped to be 
displayed.
Note
 z This is disabled when [3D SYSTEM SETTING] is 
set to any setting other than [SINGLE].
[3D COLOR MATCHING]
Switches the color matching correction data applied to 
the displayed image.
1) Press 
▲▼ to select [3D COLOR 
MA TCHING].
2)
 
Press  ◀▶ to switch [3D COLOR 
MA

TCHING].
▶zThe setting will change as follows each time 
you press the button.
[SHARED 2D/3D][SEPARATE 2D/3D]
[SHARED 
2D/3D] 2D signals and 3D signals use the 
same correction data.
[SEPARATE  2D/3D] 2D signals and 3D signals use 
different correction data.
Note
 z Keep the signal you want to adjust input when you 
s

witch the [COLOR MATCHING] (
 page 88) setting. 
						

							[3D SETTINGS] menu (PT-DZ21KU and PT- DS20KU only)
ENGLISH - 85
Settings
[3D PICTURE BALANCE]
Correct a shift when the brightness or color differ in 
the right eye and left eye images.
1) Press 
▲▼ to select [3D PICTURE 
BALANCE].
2)
 
Press the  button.
▶z The  [3D PICTURE BALANCE]
 screen is 
displayed.
3) Press  ▲▼ to select an item, and press 
◀▶  to adjust the setting.
▶z
Correct the setting value parts of the right eye 
image based on the left eye image.
[CONTRAST] You can adjust the contrast of the 
colors.
[WHITE 
BALANCE HIGH  RED] Adjusts the high red white 
balance.
[WHITE 
BALANCE HIGH  GREEN] Adjusts the high green white 
balance.
[WHITE 
BALANCE HIGH  BLUE] Adjusts the high blue white 
balance.
[BRIGHTNESS] You can adjust the dark (black) 
part of the projected image.
[WHITE 
BALANCE LOW  RED] Adjusts the low red white balance.
[WHITE 
BALANCE LOW  GREEN] Adjusts the low green white 
balance.
[WHITE 
BALANCE LOW  BLUE] Adjusts the low blue white 
balance.
[COLOR] You can adjust the color saturation 
of the projected image.
[TINT] You can adjust the skin tone in the 
projected image.
[CLOCK  PHASE] Adjust when the screen flickers or 
outline blurs.
Note
 z [CLOCK PHASE] settings go are enabled at 
simultaneous input of RGB1 and RGB2 to adjust 
the right eye image.
 zThis is disabled when [3D SYSTEM SETTING] is 
set to any setting other than [SINGLE].
 zThis is disabled when [3D 

TEST PATTERN] is 
displayed.
 z This is disabled when [3D 

TEST MODE] is set to 
any setting other than [NORMAL] and [SIDE BY 
SIDE].
▶■ To display [3D WAVEFORM 
MONITOR]
The left eye and right eye images are divided and 
displayed in a waveform on the left and right.
4) Select [3D W AVEFORM MONITOR] in 
Step 3).
5)
 
Press  ◀▶ to switch [3D W

AVEFORM 
MONITOR].
▶z The setting will change as follows each time 
you press the button.
[OFF][ON]
[OFF] The 3D waveform monitor is not 
displayed.
[ON] The 3D waveform monitor is 
displayed.
Note
 z The 3D waveform monitor is displayed only when 
the [3D PICTURE BALANCE] screen is displayed.
 zThe normal waveform monitor cannot be displayed 
in 3D images.
[DARK TIME SETTING]
Set the black display period to be displayed between 
the right eye image and the left eye image as 
necessary for the 3D system used.
1) Press 
▲▼ to select [DARK TIME 
SETTING].
2)
 
Press  ◀▶ to switch [DARK TIME 
SETTING].
▶z The setting will change as follows each time 
you press the button.
[0.5 ms][1.0 ms][1.5 ms]
[2.7 ms][2.5 ms][2.0 ms]
Note
 z This is disabled when [3D SYSTEM SETTING] is 
set to any setting other than [SINGLE].
 zWhen the setting does not correspond to the 3D 
system in use, phenomenon such as increased 
crosstalk and darkening of displayed images may 
occur

. 
						

							[3D SETTINGS] menu (PT-DZ21KU and PT- DS20KU only)
86 - ENGLISH
Settings
[3D FRAME DELAY]
Adjust the timing of the left-right switch of an image.
1) Press 
▲▼ to select [3D FRAME 
DELA Y].
2)
 
Press  ◀▶ to switch [3D FRAME 
DELA

Y].
▶zValues in the following range change by units of 
10 us.
0 us to 25 000 us
[3D TEST MODE]
Set the image display format for use with 3D system 
adjustments.
1) Press  ▲▼ to select [3D TEST MODE].
2)  
Press  ◀▶ to switch [3D TEST MODE].
▶z
The setting will change as follows each time 
you press the button.
[NORMAL][SIDE BY 
SIDE][LEFT/LEFT]
[BLACK/RIGHT][LEFT/
BLACK][RIGHT/ RIGHT]
[NORMAL] Standard setting.
[SIDE BY SIDE] The left eye image is displayed 
on the left, next to the right eye 
image displayed on the right.
[LEFT/LEFT] Both the left eye image and right 
eye image display the left eye 
input signal.
[RIGHT/RIGHT] Both the left eye image and right 
eye image display the right eye 
input signal.
[LEFT/BLACK] The left eye input signal is 
displayed in the left eye image 
and a completely black image is 
displayed in the right eye image.
[BLACK/RIGHT] A completely black image is 
displayed in the left eye image 
and the right input signal is 
displayed in the right eye image.
Note
 z The [3D 

TEST MODE] settings return to [NORMAL] 
when the projector is switched off.
 z This is disabled when [3D SYSTEM SETTING] is 
set to any setting other than [SINGLE].
 zThis is disabled when [3D 

TEST PATTERN] is 
displayed.
[3D TEST PATTERN]
The 3D test pattern can be used to check operation 
and make adjustments even without a 3D signal.
1) Press  ▲▼ to select [3D TEST 
P ATTERN].
2)
 
Press  ◀▶ to switch [3D TEST 
P

ATTERN].
▶zThe setting will change as follows each time 
you press the button.
Menu screen
+
Entry screenMenu screen +
Left: white/
Right: blackMenu screen +
Left: black/
Right: white
Note
 z The 3D test pattern cannot be displayed when the 
following inputs are selected.
–

▶
VIDEO input
–

▶
RGB1 input (only when [RGB IN] is set to [Y/C])
 zThis is disabled when [3D SYSTEM SETTING] is 
set to any setting other than [SINGLE]. 
						

							[3D SETTINGS] menu (PT-DZ21KU and PT- DS20KU only)
ENGLISH - 87
Settings
[SAFETY PRECAUTIONS 
MESSAGE]
Set to show or hide safety precaution messages 
related to 3D viewing when the projector is switched 
on.
1) Press 
▲▼ to select [SAFETY
 
PRECAUTIONS MESSAGE].
2)
 
Press  ◀▶ to switch [SAFETY

 
PRECAUTIONS MESSAGE].
▶z The setting will change as follows each time 
you press the button.
[ON][OFF]
[ON] Shows safety precaution 
messages related to 3D viewing 
when the projector is switched on.
[OFF] Hides safety precaution messages 
related to 3D viewing when the 
projector is switched on.
Note
 z Set to [OFF] to hide the safety precautions 
message when the projector is switched on.
 zA

 confirmation window is displayed when switched 
from [ON] to [OFF]. Select [OK] in the confirmation 
window and press the  button to change 
the setting to [OFF].
Attention
 z When 3D images are viewed by unspecified 
number of people for commercial use, display 
safety precaution messages related to 3D viewing 
to notify viewers.
[3D SAFETY PRECAUTIONS]
Show safety precaution messages related to 3D 
viewing.
1) Press 
▲▼ to select [3D SAFETY
 
PRECAUTIONS].
2)
 
Press the  button.
▶z The [3D SAFETY  PRECAUTIONS] screen is 
displayed.
▶z Press 
◀▶ to turn the page.
1/2
MENU
3D SAFETY PRECAUTIONS
I\f you \biew 3D image\Ns, please note below\N.
In addition, when 3D\N images will be \bie\Nwed
by unspeci\fied numbe\Nr o\f people
or used \for commercia\Nl applications,
someone in authority\N should con\bey
the \following precau\Ntions.
To enjoy 3D images s\Na\fely and com\fortabl\Ny,
please re\fer to the\N Operating Instruct\Nions
\for in-depth descri\Nption.
CHANGE
EXIT
2/2
MENU
3D SAFETY PRECAUTIONSPl\fas\f r\f\brain \brom vi\fw\ling 3D imag\fs
i\b you do not \b\f\fl w\fll\l or ar\f \fxp\fri\fncing
visual \batigu\f.
Pl\fas\f us\f th\f cont\fnt\ls which has b\f\fn
prop\frly mad\f \bor 3D.
Vi\fw \brom at l\fast th\f \lr\fcomm\fnd\fd distanc\f.\l
(3 tim\fs th\f \f\b\b\fctiv\f\l h\fight o\b th\f scr\f\fn)\l
R\f\b\fr to th\f Op\frating\l Instructions
i\b this m\fssag\f is no \llong\fr n\f\fd\fd.
CHANGE
EXIT 
						

							[DISPLAY OPTION] menu
88 - ENGLISH
Settings
Select [DISPLAY OPTION] from the main menu, 
and select the item from the sub-menu.
Refer to “Navigating through the menu” 
(
 page 61) for the operation of the menu 
screen.
 z After selecting the item, press 
◀▶ to set.
[COLOR MATCHING]
You can correct the color difference between the sets 
when multiple sets are to be used simultaneously.
1) Press 
▲▼ to select [COLOR 
MA TCHING].
2)
 
Press  ◀▶ to switch [COLOR 
MA

TCHING].
▶zThe setting will change as follows each time 
you press the button.
[OFF][3COLORS][7COLORS]
[MEASURED][709MODE]
[OFF] Color matching adjustment is not 
carried out.
[3COLORS] The three colors [RED], [GREEN], 
and [BLUE] can be adjusted.
[7COLORS] The seven colors [RED], [GREEN], 
[BLUE], [CYAN], [MAGENTA], 
[YELLOW], and [WHITE] can be 
adjusted.
[709MODE] Refer to “To use a colorimeter to 
adjust the color matching” (
 page 89) 
for details about this mode.
[MEASURED]
▶■
To set [3COLORS] or [7COLORS]
3) Select [3COLORS] or [7COLORS] in 
Step 2).
4)
 
Press the  button.
▶z The  [3COLORS] or [7COLORS] screen is 
displayed.
5) Press  ▲▼ to select [RED], [GREEN], 
and [BLUE] (for [7COLORS]: [RED], 
[
GREEN], [BLUE], [CYAN], [MAGENTA], 
[YELLOW], and [WHITE]).
6)
 
Press the  button
▶z The  [3COLORS:RED], [3COLORS:GREEN] or 
[3COLORS:BLUE] screen is displayed.
For [7COLORS], the [7COLORS:RED], 
[7COLORS:GREEN], [7COLORS:BLUE], 
[7COLORS:CYAN], [7COLORS:MAGENTA], 
[7COLORS:YELLOW]  or [7COLORS:WHITE] 
screen is displayed.
▶z Set [AUT

O TESTPATTERN] to [ON] to display 
a test pattern of selected colors.
7) Press  ◀▶ to adjust the level.
▶z
Adjustment value will change between 0 and 
2
  048.
Note
 z Operation when correcting the adjustment color
W

hen the adjustment color and the same correction 
color are moved: The luminance of the adjustment 
color will change.
When correction color red is changed: Red is 
added to or subtracted from the adjustment color.
When correction color green is changed: Green is 
added to or subtracted from the adjustment color.
When correction color blue is changed: Blue is 
added to or subtracted from the adjustment color.
 z This adjustment should be carried out by a person 
who is familiar with the projector or by a service 
person because a high level of skill is required to 
make a successful adjustment.
 zPressing the  button will restore the 
factory default settings for all items.
 z When [COLOR MA

TCHING] adjustment has been 
set to any setting other than [OFF], the [COLOR 
TEMPERATURE] is fixed to [USER1].
 z Set [3D COLOR MA

TCHING] (
 page 84) to set 
whether 2D and 3D signals are set separately or 
whether common data is used. (PT
-DZ21KU and 
PT-DS20KU only)
 z When 2D and 3D settings are set separately

, 
[NATIVE] or [3D] is displayed in the upper right of 
the menu. (PT-DZ21KU and PT-DS20KU only)
[DISPLAY OPTION] menu 
						

							[DISPLAY OPTION] menu
ENGLISH - 89
Settings
▶■To use a colorimeter to adjust the 
color matching
Use a colorimeter that can measure chromaticity 
coordinates and luminance to change the colors 
[RED], [GREEN], [BLUE], [CYAN], [MAGENTA], 
[YELLOW], and [WHITE] to desired colors.
▶z Inputting the current luminance and 
chromaticity coordinates
1)
 
Press  ▲▼ to select [COLOR 
MA

TCHING].
2)
 
Press  ◀▶ to select [709MODE] or 
[MEASURED].
3)

 
Press the  button.
▶z The  [709MODE] or [MEASURED MODE] 
screen is displayed.
4) Press  ▲▼ to select [MEASURED 
DA TA].
5)
 
Press the  button.
▶z The  [MEASURED DATA] screen is displayed.
6) Measure the luminance (Y) and the 
chromaticity coordinates (x, y) using 
the colorimeter
.
7)
 
Press  ▲▼ to select a color

, and press 
◀▶  to adjust the setting.
▶z
Set [AUT O TESTPATTERN] to [ON] to display 
a test pattern of selected colors.
8) Once all the input is completed, press 
the  button.
▶z The  [709MODE] or [MEASURED MODE] 
screen is displayed.
▶z Inputting the coordinates of desired 
colors (for [MEASURED] only)
9)
 
Press  ▲▼ to select [T

ARGET DATA].
10) Press the  button.
▶zThe  [TARGET DATA] screen is displayed.
11) Press 
▲▼ to select a color and press 
◀▶  to input coordinates for desired 
colors.
▶z Set [AUT O TESTPATTERN] to [ON] to display 
a test pattern of selected colors.
12) Once all the input is completed, press 
the  button.
Note
 z When [709MODE] is selected in [COLOR 
MA

TCHING], the ITU-R BT.709 standard three 
primary colors are set as target data.
 z Colors are not displayed properly when target data 
is a color outside the region of this projector

.
 zThe [709MODE] may dif

fer slightly from the ITU-R 
BT.709 standard colors.
 z Set the [AUT
O TESTPATTERN] to [ON] to 
automatically display a test pattern for use in 
adjusting the selected adjustment colors.
 z Before using a colorimeter or similar instrument to 
m

easure measurement data, set [PICTURE MODE] 
to [DYNAMIC].
 z A

 difference in the color coordinates of target 
data and measurement values obtained from an 
instrument may occur for certain instruments and 
measurement environments used.
 z The [AUT

O TESTPATTERN] setting s change 
in conjunction with the [AUTO TESTPATTERN] 
settings in [EDGE BLENDING].
[LARGE SCREEN 
CORRECTION]
Corrects the phenomenon in which colors that appear 
lighter when viewed on a large screen viewed from 
a close distance compared to when viewed on an 
average screen size so that colors appear the same.
1) Press  ▲▼ to select [LARGE SCREEN 
CORRECTION].
2)
 
Press  ◀▶ to switch [LARGE SCREEN 
CORRECTION].
▶z The setting will change as follows each time 
you press the button.
[OFF] (No 
correction)[1] (Low)[2] (High) 
						

							[DISPLAY OPTION] menu
90 - ENGLISH
Settings
[SCREEN SETTING] (PT-DZ21KU 
and PT
-

DS20KU only)
Set the screen size.
When changing the aspect of a projected image, 
correct to the optimum image position for the set 
screen. Set as necessary for the screen in use.
▶■ For PT -DZ21KU
1) Press 
▲▼ to select [SCREEN 
SETTING].
2)
 
Press the  button.
▶z The  [SCREEN SETTING] screen is displayed.
3) Press 
◀▶ to switch [SCREEN 
FORMA T].
[16:10][4:3][16:9]
4) Press ▲▼ to select [SCREEN 
POSITION].
5)
 
Press  ◀▶ to adjust [SCREEN 
POSITION].
▶z When [SCREEN FORMA T] is set to [16:9], the 
vertical position can be adjusted from -60 to 
+60.
▶z When [SCREEN FORMA

T] is set to [4:3], the 
horizontal position can be adjusted from -160 to 
+160.
▶■ For PT -DS20KU
1) Press 
▲▼ to select [SCREEN 
SETTING].
2)
 
Press the  button.
▶z The  [SCREEN SETTING] screen is displayed.
3) Press 
◀▶ to switch [SCREEN 
FORMA T].
[4:3][16:9]
4) Press ▲▼ to select [SCREEN 
POSITION].
5)
 
Press  ◀▶ to adjust [SCREEN 
POSITION].
▶z When [SCREEN FORMA T] is set to [16:9], the 
vertical position can be adjusted from -132 to 
+131.
Note
 z [SCREEN POSITION] cannot be adjusted in 
PT

-DZ21KU when [SCREEN FORMAT] is [16:10], 
or in PT-DS20KU when [SCREEN FORMAT] is 
[4:3].
[AUTO SIGNAL]
Set automatic execution of auto setup.
The screen display position or signal level can be 
adjusted automatically without pressing the  button on the remote control on each 
occasion if you input unregistered signals frequently 
at meetings, etc.
1) Press  ▲▼ to select [AUT
O SIGNAL].
2)  
Press  ◀▶ to switch [AUT

O SIGNAL].
▶zThe setting will change as follows each time 
you press the button.
[OFF][ON]
[OFF]
Set input auto setup to off.
[ON] Auto setup is automatically 
executed when images are 
changed to unregistered signals 
during projection.