Panasonic DLP Projector PT-DW740E PT-DW740EL PT-DX810E PT-DX810EL Operating Instructions

							ENGLISH - 61
Chapter 4 Settings — [POSITION] menu
r
r [ASPECT]
[DEFAULT]
Pictures are displayed without changing the aspect ratio of the input si\
gnals.
[VID AUTO] The projector identifies the video ID (VID) embedded in the image signals and displays the image by 
automatically switching the screen sizes between 4:3 and 16:9. This function is effective for 
VIDEO/S-VIDEO 
(NTSC)
 signals.
[S1 AUTO] The projector identifies the S1 signal, and displays the image by automatically switching the screen sizes 
between 4:3 and 16:9. This function is effective for 
S-VIDEO (NTSC) signals.
[VID AUTO(PRI.)] The projector identifies the video ID (VID) embedded in image signals and S1 signals, and displays the 
image by automatically switching the screen sizes between 4:3 and 16:9 in accordance with VID if it detects 
VID, or S1 signal if it does not detect VID. This function is effective for 
S-VIDEO (NTSC) signals.
[AUTO] The projector identifies the video ID (VID) embedded in the image signals and displays the image by 
automatically switching the screen sizes between 4:3 and 16:9. This function is effective for 480i/480p 
signals.
[THROUGH] Pictures are displayed without changing the resolution of the input sign\
als.
[16:9] When standard signals
*1 are input, the pictures are displayed with the aspect ratio converted to 16:9. When 
wide-screen signals*2 are input, the pictures are displayed without changing the aspect ratio.
[4:3] When standard signals
*1 are input, the pictures are displayed without changing the aspect ratio. When 
wide-screen signals*2 are input, if [4:3] is selected with [SCREEN FORMAT], the pictures are displayed with 
the aspect ratio converted to 4:3. When [SCREEN FORMAT] is other than [4:3], the picture size is reduced 
without changing the aspect ratio so that the pictures will fit in the 4:3 screen.
[H FIT] The pictures are displayed using the entire width of the screen range selected with [SCREEN FORMA
T]. 
When signals have the aspect ratio vertically longer than the aspect rat\
io of the screen selected with 
[SCREEN FORMAT], the pictures are displayed with the top and bottom parts cut off.
[V FIT] The pictures are displayed using the entire height of the screen range selected with [SCREEN FORMA
T]. 
When signals have the aspect ratio horizontally longer than the aspect r\
atio of the screen selected with 
[SCREEN FORMAT], the pictures are displayed with the right and left parts cut off.
[HV FIT] The pictures are displayed in the entire screen range selected with [SCREEN FORMA
T]. When the aspect 
ratio of the input signals differs from that of the screen range, the pictures are displayed with the \
aspect 
ratio converted to that of the screen selected with [SCREEN FORMA T].
*1 Standard signals are input signals with an aspect ratio of 4:3 or 5:4.
*2  Wide-screen signals are input signals with an aspect ratio of 16:10, 16:9, 15:9 or 15:10.
Note
r
f Some size modes are not available for certain types of input signals. [DEF
AULT] cannot be selected for NTSC signals.
r
f If an aspect ratio which is different from the aspect ratio for the input signals is selected, the pictures will appear differently from the originals. 
Be careful of this when selecting the aspect ratio.
r
f If using this projector in places such as cafes or hotels to display pro\
grams for a commercial purpose or for public presentation, note that 
adjusting the aspect ratio or using the zoom function to change the scre\
en pictures may be an infringement of the rights of the original 
copyright owner for that program under copyright protection laws. Take care when using a function of the projector such as the aspect ratio\
 
adjustment and zoom function.
r
f If conventional (normal) 4:3 pictures which are not wide-screen pictures are displayed on a wide screen, the edges of the pictures may not 
be visible or they may become distorted. Such pictures should be viewed with an aspect ratio of 4:3 in the original format intended by the 
creator of the pictures.
[ZOOM]
You can adjust the size of the projected image.
When [ASPECT] is set to other than [DEFAULT] or [THROUGH]
1) Press as to select [ZOOM].
2) Press the  button.
r
f The 
[ZOOM]  screen is displayed.
3) Press as to select [INTERLOCKED].
4) Press qw to switch [INTERLOCKED].
5) Press as to select [VERTICAL] or 
[HORIZONTAL].
r
f Select 
[BOTH]  when [ON] is selected.
6) Press qw to adjust.
r
r [INTERLOCKED]
[OFF] [VERTICAL]
Set the [VERTICAL] and [HORIZONTAL] zoom ratio.
[HORIZONTAL]
[ON] [BOTH]Use [BOTH] to set zoom ratio. Horizontal and vertical can be expanded 
by units of 1.0 time.  
						

							62 - ENGLISH
Chapter 4 Settings — [POSITION] menu
Note
r
f When [ASPECT] is set to [THROUGH], [ZOOM] is not displayed.
When [ASPECT] is set to [DEFAULT]
1) Press as to select [ZOOM].
2) Press the  button.
r
f The 
[ZOOM]  screen is displayed.
3) Press as to select [MODE].
4) Press qw to switch [MODE].
5) Press as to select [INTERLOCKED].
6) Press qw to switch [INTERLOCKED].
7) Press as to select [VERTICAL] or 
[HORIZONTAL].
r
f Select 
[BOTH]  when [ON] is selected.
8) Press qw to adjust.
r
r [MODE]
[INTERNAL]
Enlarges the size within the aspect range set with [SCREEN FORMA T].
[FULL] Enlarges the size to the entire display area set with [SCREEN FORMA T].
r
r [INTERLOCKED]
[OFF] [VERTICAL]
Set the [VERTICAL] and [HORIZONTAL] zoom ratio.
[HORIZONTAL]
[ON] [BOTH]Use [BOTH] to set zoom ratio. Horizontal and vertical can be expanded 
by units of 1.0 time.
Note
r
f When [ASPECT] is set to other than [DEFAULT], [MODE] is not displayed.
[CLOCK PHASE]
You can adjust to achieve an optimal image when there is a flickering image or smeared outlines.
1) Press as to select [CLOCK PHASE].
2) Press qw or the  button.
r
f The 
[CLOCK PHASE]  individual adjustment screen is 
displayed.
3) Press qw to adjust.
r
f Adjustment value will change between 0 and +31. Adjust so that 
the amount of interference is at a minimum.
Note
r
f Optimal value may not be achieved if the output from the input computer is unstable.
r
f Optimal value may not be achieved when there is a shift in the total dot numbers.
r
f [CLOCK PHASE] can be adjusted only when a signal is input to the  terminal or the  terminal.
r
f [CLOCK PHASE] cannot be adjusted when a digital signal is input.
r
f If you press 
w while the adjustment value is [+31], the value will become [0]. If you press 
q while the adjustment value is [0], the value will 
become [+31].  
						

							ENGLISH - 63
Chapter 4 Settings — [POSITION] menu
[KEYSTONE]
You can correct the trapezoidal distortion that occurs when the projector\
 is installed tilted or when the screen is tilted.
1) Press as to select [KEYSTONE].
2) Press the  button.
r
f The 
[KEYSTONE]  screen is displayed.
3) Press as to select the item to adjust.
4) Press qw to adjust.
r
r Adjustment details
[KEYSTONE]
[SUB KEYSTONE]
[LINEARITY]
Note
r
f The menu or logo may run off the screen when various adjustments are performed with [KEYSTONE].
r
f Various adjustments with [KEYSTONE] are possible to correct up to ±40° for the tilt in vertical direction. However, the picture quality will 
degrade and it will get harder to focus with more correction. Install the projector so the correction will be as small as possible. (±30° when 
using fixed-focus lens (ET-DLE055), or super short focus zoom lens (ET-DLE080/ET-DLE085).)
r
f Image size will also change when [KEYSTONE] is used to perform adjustments.
r
f Trapezoidal distortion may occur depending on the lens shift position.
r
f Aspect ratio of the image size may shift depending on the correction or \
lens zoom value.  
						

							64 - ENGLISH
Chapter 4 Settings — [ADVANCED MENU] menu
[ADVANCED MENU] menu
Select [ADVANCED MENU] from the main menu, and select the item from the sub-menu.
Refer to “Navigating through the menu” (
x page 51) for the operation of the menu screen.
r
f After selecting the item, press 
asqw to adjust.
[DIGITAL CINEMA REALITY]
You can increase the vertical resolution and enhance the picture quality by performing the cinema processing when the PAL (or the SECAM) 
576i signal, the NTSC 480i, 1080/50i, and 1080/60i signals are input.
1) Press as to select [DIGITAL CINEMA 
REALITY].2) Press qw to switch [DIGITAL CINEMA 
REALITY].
r
f The setting will change among [AUTO], [OFF] and [25p 
FIXED]*1/[30p FIXED]*2 each time you press the button.
*1 
Only during 576i,1080/50i signal input
*2  Only during 480i,1080/60i signal input
r
r [DIGITAL CINEMA REALITY]
[AUTO]
Performs automatic detection and cinema processing. (Factory default)
[OFF] Unforced cinema processing.
[25p FIXED] Forced cinema processing (2:2 pulldown) is performed when a 576i or 1080/50i signal is input.
[30p FIXED] Forced cinema processing (2:2 pulldown) is performed when a 480i or 1080/60i signal is input.
Note
r
f When a signal other than a 2:2 pulled-down signal is set to [25p FIXED] or [30p FIXED] in [DIGIT
AL CINEMA REALITY], picture quality 
deteriorates. (Vertical resolution will degrade.)
[BLANKING]
The blanking width is adjusted when there are noise at the edge of the s\
creen or the image is slightly running out from the screen when an 
image from the VCR or other devices are projected.
1) Press as to select [BLANKING].
2) Press the  button.
r
f The 
[BLANKING]  adjustment screen is displayed.
3) Press as to select an adjustment item.
4) Press qw to adjust the blanking.
r
r Adjustment details
Blanking correction
ItemOperation Adjustment Range
Top of the screen [UPPER]Press 
q. The blanking zone 
moves upward.
PT-DW740E: 0 to 399
PT-DX810E: 0 to 383
Press 
w. The blanking zone 
moves downward.
Bottom of the screen [LOWER]Press 
w. The blanking zone 
moves upward.
Press 
q. The blanking zone 
moves downward.           
						

							ENGLISH - 65
Chapter 4 Settings — [ADVANCED MENU] menu
Blanking correction ItemOperation Adjustment Range
Left side of the screen [LEFT]Press 
w. The blanking zone 
moves to the right.
PT-DW740E: 0 to 639
PT-DX810E: 0 to 511
Press 
q. The blanking zone 
moves to the left.
Right side of the  screen [RIGHT]Press 
q. The blanking zone 
moves to the right.
Press 
w. The blanking zone 
moves to the left.
[INPUT RESOLUTION]
You can adjust to achieve an optimal image when there is a flickering image or smeared outlines.
1) Press as to select [INPUT RESOLUTION].
2) Press the  button.
r
f The 
[INPUT RESOLUTION]  screen is displayed.
3) Press as to select [TOTAL DOTS], [DISPLAY 
DOTS], [TOTAL LINES], or [DISPLAY LINES], 
then press qw to adjust it.
r
f Values corresponding to the input signal are displayed 
automatically for each item. Change the displayed values and 
adjust to the optimal image viewing the screen when there is a 
vertical banding or missing in the screen.
Note
r
f Previously mentioned vertical banding will not occur with all white sign\
al input.
r
f The image may be disrupted while performing the adjustment, but it is no\
t a malfunction.
r
f [INPUT RESOLUTION] can be adjusted only when an RGB signal is input to the  terminal or the  terminal.
r
f Certain signals may not be adjustable.
[CLAMP POSITION]
You can adjust the optimal point when the black part of the image is blun\
t or it has turned green.
1) Press as to select [CLAMP POSITION].2) Press qw to adjust.
r
r Adjustment details
Status
Rough guide for optimal value Range
The black part is blunt. The point where bluntness of the black part improves the most 
is the optimal value.
1 - 255
The black part is green. The point where the green part becomes black, and the 
bluntness improves is the optimal value.
Note
r
f [CLAMP POSITION] can be adjusted only when a signal is input to the  terminal or the  terminal.
r
f Certain signals may not be adjustable.
[EDGE BLENDING]
The edge blending function allows multiple projector images to be seamle\
ssly overlapped by using the inclination of the brightness at the 
overlapped area.
1) Press as to select [EDGE BLENDING].
2) Press qw to switch [EDGE BLENDING].
r
f The setting will change between [ON] and [OFF] each time you 
press the button.
r
f To adjust edge blending, proceed to Step 
3).
3) Press the  button when [ON] is 
selected.
r
f The 
[EDGE BLENDING]  screen is displayed.
4) Press as to specify the location to be 
corrected.
r
f When joining at top: Set [UPPER] to [ON].
r
f When joining at bottom: Set [LOWER] to [ON].
r
f When joining at left: Set [LEFT] to [ON].
r
f When joining at right: Set [RIGHT] to [ON].
5) Press qw to switch between [ON] and [OFF].
r
f To adjust edge blending without displaying the adjustment 
marker, proceed to Step 
8).
6) Press as to select [MARKER].  
						

							66 - ENGLISH
Chapter 4 Settings — [ADVANCED MENU] menu
7) Press qw to switch [ON].
r
f A marker for image position adjustment is displayed.
8) Press as to select [START] or [WIDTH], 
then press qw to adjust starting point and 
correction width.
r
f The green line is the starting point of edge blending adjusted 
with [START]. The red line is the ending point of edge blending 
adjusted with [WIDTH]. The position where the red and green 
lines overlap for the sets to join will be the optimal point.
Make sure to set the correction width for the sets to join as the 
same value. Optimal joining is not possible with the sets with 
different correction widths.
The optimal point is the point at which these lines overlap.
Green line
Red line
9) Press as to select [GAMMA].
10) Press qw to switch [GAMMA].
r
f The setting will change among [2.2], [1.8], and [2.0] each time 
you press the button.
11) Press as to select [BRIGHT ADJUST].
12) Press the  button.
r
f The 
[BRIGHT ADJUST]  screen is displayed.
13) Press as to select [BRIGHT INSIDE].
14) Press the  button.
r
f The 
[BRIGHT INSIDE]  individual adjustment screen is 
displayed.
r
f If [INTERLOCKED] is set to [OFF], [RED], [GREEN], and [BLUE] 
can be adjusted individually.
15) Press as to select an item, then press 
qw to 
adjust it.
r
f Once the adjustment is completed, press the  button to 
return to the 
[BRIGHT ADJUST]  screen.
16) Press as to select [UPPER], [LOWER], [LEFT], 
or [RIGHT] from [OUTSIDE AREA].
17) Press qw to set the region (width) of the 
[BRIGHT INSIDE] adjustment.
18) Press as to select [BRIGHT OUTSIDE].
19) Press the  button.
r
f The 
[BRIGHT OUTSIDE]  individual adjustment screen is 
displayed.
r
f If [INTERLOCKED] is set to [OFF], [RED], [GREEN], and [BLUE] 
can be adjusted individually.
20) Press as to select an item, then press 
qw to 
adjust it.
[OUTSIDE  AREA] (Right)
Projection range Edge blending [WIDTH] (Right)
[MARKER] (Red)
Edge blending [S TART ] (Right)
([MARKER] (Green))
[BRIGHT OUTSIDE]
[BRIGHT INSIDE ]
r
r [EDGE BLENDING]
[OFF]
Sets the edge blending function to off.
[ON] Use the setting value of the internal distortion of the set for the incl\
ination of the edge blending area.
r
r [GAMMA]
[2.2]
The screen becomes darker as the value increases. Set this item accordin\
g to the condition of the joined 
part.
[1.8]
[2.0]
Note
r
f [BRIGHT ADJUST] is a function that makes the increased brightness in black level of the overlapping image area difficult to notice when 
[EDGE BLENDING] is used to configure multiple screens. The optimal point of the correction is set by adjusting [BRIGHT INSIDE] so the 
black level of the overlapping image area will be the same level as the \
non-overlapping area. If the bordering part of the part where the 
image is overlapping and the non-overlapping part gets brighter after adjusting [BRIGHT
 INSIDE], adjust the width of the top, bottom, left, or 
right. Adjust [BRIGHT OUTSIDE] when the width adjustment makes only the border area darker.
r
f The joining part may look discontinuous depending on the position you ar\
e looking from when a screen with high gain or rear screen is used.
[RASTER POSITION]
This will allow the position of the image to move within the display are\
a arbitrarily when the input image is not using the whole display area.
1) Press as to select [RASTER POSITION].
2) Press the  button.
r
f The 
[RASTER POSITION]  screen is displayed.
3) Press asqw to adjust the position.  
						

							ENGLISH - 67
Chapter 4 Settings — [DISPLAY LANGUAGE] menu
[DISPLAY LANGUAGE] menu
Select [DISPLAY LANGUAGE] from the main menu, and display the sub-menu.
Refer to “Navigating through the menu” (
x page 51) for the operation of the menu screen.
r
f Press 
as to select a language, and press the  button to set.
Changing the display language
You can select the language of the on-screen display.
Ô
ÔŠ 
DISPLA Y LANGUAGE
r
f Various menus, settings, adjustment screens, control button names, etc., are displayed in the selected language.
r
f The language can be changed to English, German, French, Spanish, Italian, Japanese, Chinese, Russian, and Korean.
Note
r
f The on-screen display language of the projector is set to English by default, and also when [ALL
 USER DATA] (
x page 84) is executed 
from [INITIALIZE].     
						

							68 - ENGLISH
Chapter 4 Settings — [DISPLAY OPTION] menu
[DISPLAY OPTION] menu
Select [DISPLAY OPTION] from the main menu, and select the item from the sub-menu.
Refer to “Navigating through the menu” (
x page 51) for the operation of the menu screen.
r
f After selecting the item, press 
asqw to set.
[COLOR MATCHING]
You can correct the color difference between the sets when multiple sets are to be used simultaneousl\
y.
To adjust the color matching as desired
1) Press as to select [COLOR MATCHING].
2) Press qw to switch [COLOR MATCHING].
r
f The setting will change among [OFF], [3COLORS], [7COLORS] 
and [MEASURED] each time you press the button.
3) Select [3COLORS] or [7COLORS], and press 
the  button.
r
f The 
[3COLORS]  or [7COLORS]  screen is displayed.
4) Press as to select [RED], [GREEN] or [BLUE] 
([RED], [GREEN], [BLUE], [CYAN], [MAGENTA], 
[YELLOW], or [WHITE] for [7COLORS]).
5) Press the  button.
r
f The [3COLORS:RED], [3COLORS:GREEN], [3COLORS:BLUE], 
or [3COLORS:WHITE] screen is displayed. 
In the case of [7COLORS], the [7COLORS:RED], 
[7COLORS:GREEN], [7COLORS:BLUE], [7COLORS:CYAN], 
[7COLORS:MAGENTA], [7COLORS:YELLOW], or 
[7COLORS:WHITE] screen is displayed.
6) Press 
as to select [RED], [GREEN], or [BLUE].
r
f If [WHITE] is selected from [3COLORS], only [GAIN] can be 
adjusted.
7) Press qw to adjust.
r
f Adjustment value will change between 0* and 2 048.
* 
The lower limit differs depending on the color to be adjusted.
r
r [COLOR MATCHING]
[OFF]
Color matching adjustment is not carried out.
[3COLORS] The three colors [RED], [GREEN], and [BLUE] can be adjusted.
[7COLORS] The seven colors [RED], [GREEN], [BLUE], [CYAN], [MAGENTA], [YELLOW], and [WHITE] can be 
adjusted.
[MEASURED] Refer to “To adjust the color matching using a colorimeter” (
x page 68) for details about this mode.
Note
r
f Operation when correcting the adjustment color
When the correction color same as the adjustment color is changed: The luminance of the adjustment color changes.
When correction color red is changed: Red is added to or subtracted from\
 the adjustment color.
When correction color green is changed: Green is added to or subtracted from the adjustment color
.
When correction color blue is changed: Blue is added to or subtracted fr\
om the adjustment color.
r
f This adjustment should be carried out by a person who is familiar with t\
he projector or by a service person because a high level of skill is 
required to make a successful adjustment.
r
f Pressing the  button will restore the factory default settings for all items.
r
f When [COLOR MATCHING] is set to other than [OFF], [AI] and [COLOR CORRECTION] are fixed to [OFF], and [COLOR TEMPERATURE] 
is fixed to [USER]. (However, [WHITE BALANCE HIGH] cannot be adjusted.)
To adjust the color matching using a colorimeter
Use a colorimeter that can measure chromaticity coordinates and luminance to change the colors [RED], [GREEN], [BLUE], [CY
AN], 
[MAGENTA], [YELLOW], and [WHITE] to desired colors.
1) Press as to select [COLOR MATCHING].
2) Press qw to select [MEASURED].
3) Press the  button.
r
f The 
[MEASURED MODE]  screen is displayed.
4) Press as to select [MEASURED DATA].           
						

							ENGLISH - 69
Chapter 4 Settings — [DISPLAY OPTION] menu
5) Press the  button.
r
f The 
[MEASURED DATA]  screen is displayed.
6) Measure the current luminance (Y) and the 
chromaticity coordinates (x, y) using the 
colorimeter.
7) Press as to select a color, then press qw to 
adjust the value.
8) Once all the input is completed, press the 
 button.
r
f The 
[MEASURED MODE]  screen is displayed.
9) Press as to select [TARGET DATA].
10) Press the  button.
r
f The 
[TARGET DATA]  screen is displayed.
11) Press as to select a color, and press qw to 
input coordinates for desired colors.
12) Once all the input is completed, press the 
 button.
Note
r
f Colors are not displayed properly when target data is a color outside th\
e region of this projector.
r
f Set the [AUTO TESTPATTERN] to [ON] to automatically display a test pattern for use in adjusting the selected adjustment colors.
r
f When using a colorimeter or similar instrument to measure measurement data, measure the colors displayed with [AUT
O TESTPATTERN].
r
f A difference in the color coordinates of target data and measurement values o\
btained from an instrument may occur for certain instruments 
and measurement environments used.
[COLOR CORRECTION]
Colors can be adjusted and registered for each input signal format.
1) Press as to select [COLOR CORRECTION].2) Press qw to switch [COLOR CORRECTION].
r
r [COLOR CORRECTION]
[OFF]
Standard setting
[USER] For each of the four signal formats, VIDEO, S-VIDEO, RGB, and YC
BCR/YPBPR, six colors including red, 
green, blue, cyan, magenta, and yellow can be adjusted and registered. Press the  button to set 
details. The adjustment range is between 
-30 and +30.
[CONTRAST MODE]
There are two modes. Set according to the operating environment.
1) Press as to select [CONTRAST MODE].2) Press qw to switch [CONTRAST MODE].
r
r [CONTRAST MODE]
[NORMAL]
Maximizes brightness.
[HIGH] Maximizes contrast.
[SCREEN SETTING]
Set the screen size.
When changing the aspect of a projected image, correct to the optimum im\
age position for the set screen. Set as necessary for the screen in 
use.
1) Press as to select [SCREEN SETTING].
2) Press the  button.
r
f The 
[SCREEN SETTING]  screen is displayed.
3) Press qw to switch [SCREEN FORMAT].
r
f The setting will change between [16:10] and [16:9] for 
PT-DW740E, or [4:3] and [16:9] for PT-DX810E.
4) Press as to select [SCREEN POSITION].
5) Press qw to adjust [SCREEN POSITION].
r
r [SCREEN FORMAT]
PT-DW740E [16:10]
[SCREEN POSITION] Cannot be adjusted.
[16:9] Vertical position can be adjusted between -40 and 
40.
PT-DX810E [4:3]
Cannot be adjusted.
[16:9] Vertical position can be adjusted between 
-96 and 
96.  
						

							70 - ENGLISH
Chapter 4 Settings — [DISPLAY OPTION] menu
[AUTO SIGNAL]
Set automatic execution of auto setup.
The screen display position or signal level can be adjusted automatically without pressing the  button on the remote control on 
each occasion if you input unregistered signals frequently at meetings, \
etc.
1) Press as to select [AUTO SIGNAL].2) Press qw to switch [AUTO SIGNAL].
r
f The setting will change between [OFF] and [ON] each time you 
press the button.
r
r [AUTO SIGNAL]
[OFF]
Set input auto setup to off.
[ON] Auto setup is automatically executed when images are changed to unregistered signals during projection.
[AUTO SETUP]
You can set when adjusting a special signal or horizontally long (16:9, etc.) signal.
1) Press as to select [AUTO SETUP].
2) Press the  button.
r
f The 
[AUTO SETUP]  screen is displayed.
3) Press qw to switch [MODE].
r
f The setting will change among [DEFAULT], [WIDE], and [USER] 
each time you press the button.
r
f When [DEFAULT] or [WIDE] is selected, proceed to Step 
6).
r
f When [USER] is selected, proceed to Step 
4).
4) Press as to select [DISPLAY DOTS], and 
press qw to adjust [DISPLAY DOTS] to the 
horizontal resolution of the signal source.
5) Press as to select [MODE].
6) Press the  button.
r
f Automatic adjustment is executed. [PROGRESS] is displayed 
while automatically adjusting. When complete, the system 
returns to the 
[AUTO SETUP]  screen.
r
r [MODE]
[DEFAULT] Select when receiving a signal whose image aspect is 4:3 or 5:4. (Supported resolutions are 640 x 400, 
640 x 480, 800 x 600, 832 x 624, 1 024 x 768, 1 152 x 864, 1 152 x 870, 1 280 x 960, 1 280 x 1 024, 1 600 
x 1 200, and 1 400 x 1 050.)
[WIDE] Select when receiving a signal whose image aspect is wide-screen. (Supported resolutions are 1 280 x 
720, 1 280 x 800, 1 440 x 900, 1 680 x 1 050, 1 920 x 1 080, and 1 920 x 1 200.)
[USER] Select when receiving a signal with a special horizontal resolution (number of display dots).
[RGB IN]
Set to match the signal to input to the  terminal.
1) Press as to select [RGB IN].
2) Press the  button.
r
f The 
[RGB IN]  screen is displayed.
3) Press as to select [RGB1 SYNC SLICE 
LEVEL] or [RGB2 SYNC SLICE LEVEL].
4) Press qw to switch between [RGB1 SYNC 
SLICE LEVEL] and [RGB2 SYNC SLICE 
LEVEL].
r
f The setting will change between [LOW] and [HIGH] each time 
you press the button.
r
r [RGB1 SYNC SLICE LEVEL] and [RGB2 SYNC SLICE LEVEL]
[LOW]
Set the slice level to [LOW].
[HIGH] Set the slice level to [HIGH].
[DVI-D IN]
Switch the setting when the external equipment is connected to the  terminal of the projector and the image is not projected 
correctly.
1) Press as to select [DVI-D IN].
2) Press the  button.
r
f The 
[DVI-D IN]  screen is displayed.
3) Press as to select [DVI EDID].
4) Press qw to switch [DVI EDID].
r
f The setting will change among [EDID3], [EDID1], 
and[EDID2:PC] each time you press the button.
5) Press as to select [DVI SIGNAL LEVEL].