Panasonic DLP Based Projector PT-DZ570U PT-DW530U PT-DX500U Operating Instructions

							DISPLAY OPTION menu
ENGLISH - 61
Settings
[SIDE BY SIDE MODE] options 
J
MODE 1:
Projects dual screens by fully using the horizontal 
size of each screen.
The aspect ratio is held. 
z
The main and sub- 
z
screens have the same 
height.
The screens are 
 
z
centered in vertical 
direction.
MODE 2:
The main and sub-screens have a 1-to-1 
horizontal ratio.
MODE 3:
The main and sub-screens have a 2-to-1 
horizontal ratio.
MODE 4:
The main and sub-screens have a 1-to-2 
horizontal ratio.
4 : 316 : 9
4 : 316 : 9
4 : 316 : 9
4 : 316 : 9 
						

							62 - ENGLISH
Settings
PROJECTOR SETUP menu
See  
z“Navigating through the menu ”  
(
Æpage 39).
See 
 
z“MAIN MENU” and “SUB MENU ”  
(
Æpage 40).
PROJECTOR ID
The projector has an ID number setting function that 
helps the user to control two or more projectors either 
simultaneously or separately with a single remote 
control.
Press ▲▼ to select [PROJECTOR ID].
1  ) 
Press ◄► to switch [PROJECTOR ID].
2  ) 
The setting will change as follows each time  
z
◄► is pressed.
ALL1
6 2
Note
The ID number can be set to [ALL], or selected from [1] 
 
z
to [6].
If the projectors are given ID numbers, their remote 
 
z
controls must be assigned the same ID numbers, 
respectively.
If the ID number of a projector is set to [ALL], it can be 
 
z
controlled by the remote control or the PC with any ID 
number.
If multiple projectors are used and some of them 
have their IDs set to “ALL”, they cannot be controlled 
separately from the projectors with other ID numbers. 
For details on remote control ID setting, refer to “Setting 
projector ID number to remote control” (
Æpage 21).
INSTALLATION
A projection scheme can be chosen depending on 
the installation of the projector. If the picture is shown 
upside down or in reverse, change the projection 
scheme.
Select the setting by displaying the on-screen 
 
z
indications using buttons of the remote control or 
the control panel on the main unit.
Press ▲▼ to select [INSTALLATION].
1  ) 
Press ◄► to switch [INSTALLATION].
2  ) 
The setting will change as follows each time  
z
◄► is pressed.
FRONT/FLOORFRONT/CEILING
REAR/CEILINGREAR/FLOOR
FRONT/ 
FLOOR Setting on a desk/floor and 
projecting from front
FRONT/ 
CEILING Mounting on the ceiling and 
projecting from front
REAR/ 
FLOOR Setting on a desk/floor and 
projecting from rear
REAR/ 
CEILING Mounting on the ceiling and 
projecting from rear
COOLING
 CONDITION
You can control the fan speed for projecting 
angle. When the projector is angled, [COOLING 
CONDITION] setting must be set correctly. Failure to 
observe this may result in malfunctions, or the life of 
the lamp or the other components may be shortened.
Press ▲▼ to select [COOLING 
1  ) 
CONDITION].
Press  button.
2  ) 
The [COOLING CONDITION] screen will be  
z
displayed.
Press ▲▼ to select cooling condition.
3  ) 
Press  button.
4  ) 
When the confirmation message is 
5  ) 
displayed, select [OK] or [CANCEL].
CEILING   
SETTING
30° 30°
VERTICAL DOWN  SETTING
30° 30°
VERTICAL UP 
 
SETTING
FLOOR  
SETTING 
						

							PROJECTOR SETUP menu
ENGLISH - 63
Settings
HIGH ALTITUDE MODE
If you use the projector at high elevation (1 400 m to 
2 700 m), the [HIGH ALTITUDE MODE] setting needs 
to be [ON] to set the fan speed high.
Press ▲▼ to select [HIGH ALTITUDE 
1  ) 
MODE].
Press ◄► to switch [HIGH ALTITUDE 
2  ) 
MODE] and press  to select.
The setting will change as follows each time  
z
◄► is pressed.
OFFON
OFF Select this when using in normal 
environment (less than 1 400 m 
above sea level)
ON Select this when using at high 
altitude (above 1 400 m and less 
than 2 700 m above sea level)
When the confirmation message is 
3  ) 
displayed, select [OK] or [CANCEL].
Note
The loudness of fan noise depends on the [HIGH 
 
z
ALTITUDE MODE] setting.
The separately-sold Smoke Cut Filter cannot be used 
 
z
when the [HIGH ALTITUDE MODE] is [ON].
LAMP POWER
Can switch the electric power of projector lamp. Set 
the lamp power to meet the environment and purpose 
of projection.
Press ▲▼ to select [LAMP POWER].
1  ) 
Press ◄► to switch [LAMP POWER].
2  ) 
The setting will change as follows each time the  
z
button is pressed.
NORMALECO
NORMAL Sets the normal lamp intensity.
ECO Sets the reduced lamp intensity.
Note The [ECO] mode can reduce the power 
 
z
consumption, reduce the operation noise, and 
increase the service life of projector lamp.
The [LAMP POWER] may not drop automatically if:
 
z
You have set the [LAMP POWER] to [NORMAL].• 
Automatic power drop may fail immediately after • 
the lamp is turned on or the [LAMP POWER] is 
set.
ECO MANAGEMENT
Can optimize lamp power and reduce the power 
consumption according to the application.
Press ▲▼ to select [ECO 
1  ) 
MANAGEMENT].
Press  button.
2  ) 
The [ECO MANAGEMENT] screen is displayed. 
z
Press ▲▼ to select ECO 
3  ) 
MANAGEMENT.
Press ◄► to switch the setting.
4  ) 
AUTO POWER SAVE 
J
[AMBIENT LIGHT DETECTION], 
[SIGNAL
 DETECTION], and [AV MUTE DETECTION] 
functions can be used.
Select [AUTO POWER SAVE] in Step 3.
1. 
Press ◄► to switch [AUTO POWER 
2. 
SAVE] setting.
The setting will change as follows each time the  
z
button is pressed.
ONOFF
Press ▲▼ to select AUTO POWER 
3. 
SAVE conditions.
AMBIENT LIGHT 
DETECTION Adjusts the lamp power according 
to the ambient brightness.
SIGNAL 
DETECTION Drops the lamp power when no 
signal is input.
AV MUTE 
DETECTION Drops the lamp power in the AV 
Mute mode.
Press ◄►to enable or disable the 
4. 
selected condition.
The setting will change as follows each time the  
z
button is pressed
ONOFF 
						

							PROJECTOR SETUP menu
64 - ENGLISH
Settings
NO SIGNAL SHUT-OFF 
J
If no signal is input within a preset time, the projector 
power is automatically switched to the standby state.
Select [NO SIGNAL SHUT-OFF] in Step 
1. 
3.
Press ◄► to switch [NO SIGNAL 
2. 
SHUT-OFF] setting.
DISABLE The NO SIGNAL SHUT-OFF is 
ineffective.
10 to 90 minutes The Auto Power-Off time can be 
set in 10 minute increments.
STANDBY MODE 
J
This function can set the electric power when the 
projector is standing by.
Select [STANDBY MODE] in Step 3.
1  ) 
Press ◄► to switch [STANDBY MODE] 
2  ) 
setting.
The setting will change as follows each time the  
z
button is pressed.
NORMALECO
Note
If STANDBY MODE is set to [ECO], you cannot use 
 
z
network functions when the projector is standing by. Also, 
you cannot use some RS-232C protocol commands. 
When you turn the POWER switch [ON], display of 
the initial image may be delayed for approximately 
10 seconds when compared with [NORMAL] mode 
operation.
If set to [NORMAL], you can use network functions when 
 
z
the projector is standing by.
SCHEDULE
This sets the command execution schedule for each 
day of the week.
 
JHow to enable the SCHEDULE 
function
Press ▲▼ to select [SCHEDULE].
1  ) 
Press ◄► to switch [SCHEDULE].
2  ) 
The setting will change as follows each time  
z
◄► is pressed.
ONOFF
Note
If [SCHEDULE] is set to [ON], the setting for [STANDBY 
 
z
MODE] is automatically set to [NORMAL] and cannot be 
changed. Even if [SCHEDULE] is then set to [OFF] when 
in this state, the setting of [STANDBY MODE] remains at 
[NORMAL].
 
JHow to assign a program
With [SCHEDULE] switched to [ON], 
1  ) 
press  button.
The [SCHEDULE] screen will be displayed. 
z
Select and assign program to each day 
2  ) 
of week.
Press ▲▼ to select a day of week and press  
z
◄► to select a program number.
You can set the program from No.1 to No.7. 
 
z
“- - -” indicates that the program number has 
not been set yet.
 
JHow to set a program
You can set up to 16 commands to each program.
On the [SCHEDULE] screen, press ▲▼ 
1  ) 
to select [PROGRAM EDIT].
Press ◄► to select a program number 
2  ) 
to be set and press  button.
Press ▲▼ to select a command 
3  ) 
number and press  button.
You can change the page using ◄►. 
z 
						

							PROJECTOR SETUP menu
ENGLISH - 65
Settings
Press ▲▼ to select [TIME] or 
4  ) 
[COMMAND] and change the setting 
according to the instructions of the 
menu.
TIME Set the time at which the command 
will be executed using ▲▼ buttons.
COMMAND Select a command to execute at the 
set time from the following.
POWER ON
• 
STANDBY• 
AV MUTE ON• 
AV MUTE OFF• 
INPUT RGB1• 
INPUT RGB2• 
INPUT VIDEO• 
INPUT S-VIDEO• 
INPUT DVI-D• 
INPUT HDMI• 
INPUT • 
NETWORK
LAMP POWER 
• 
NORMAL
LAMP POWER 
• 
ECO SIDE BY SIDE 
• 
MODE OFF
SIDE BY SIDE 
• 
MODE1
SIDE BY SIDE 
• 
MODE2
SIDE BY SIDE 
• 
MODE3
SIDE BY SIDE 
• 
MODE4
IN STANDBY 
• 
MODE (AUDIO) 
ON
IN STANDBY 
• 
MODE (AUDIO) 
OFF
VOLUME
• 
PT-DZ570U/PT-DW530U only
: 
Û
Press ▲▼ to select [STORE] and 
5  ) 
press  button.
Note
If you try to register a setting that would cause the lamp to  
z
flash for a short time, an error message will be displayed on 
the screen. Set the [TIME] and [COMMAND] again.
To delete a command which has been set, press 
 
z
 button.
If multiple commands have been set for the same time, 
 
z
they are executed in chronological order starting from the 
smallest command number.
The setting time operates under the local time.   
 
z
(
Æpage 67)
If an operation is executed with the remote control or 
 
z
control panel of the projector or with a control command 
before the command set in the schedule is executed, the 
command set with this function may not be executed.
RS-232C
This sets the communication parameters at the serial 
terminals.
Press ▲▼ to select [RS-232C].
1  ) 
Press  button.
2  ) 
The [ 
zRS-232C ] screen will be displayed.
Press ▲▼ to select communication 
3  ) 
conditions.
press ◄► to change the setting.
4  ) 
Note
Refer to 
 
z “Serial terminal
” (Æpage 82).
 
JSelecting items in [EMULATE]
When using the control commands for one of our 
projectors that you have previously purchased to 
control this projector using a computer via its serial 
input terminal, set up the EMULATE function as 
follows. This will allow you to use the control software 
etc. designed for our existing projectors.
Select [EMULATE] in step 3).
1. 
Press  button.
2. 
Press ▲▼ to select the required item.
3. 
Press  button.
4. 
● DEFAULT DZ570 Series, DW530 Series, 
DX500 Series
L730  
SERIES L520 Series, L720 Series, 
L730 Series
L780  
SERIES L750 Series, L780 Series
L735  
SERIES L735 Series
L785  
SERIES L785 Series
F SERIES F100 Series, FW100 Series, 
F200 Series, F300 Series, 
FW300 Series 
LB SERIES LB75 Series, LB78 Series, 
LB80 Series, LB90 Series, 
LB1 Series, LB2 Series, 
ST10 Series  
						

							PROJECTOR SETUP menu
66 - ENGLISH
Settings
REMOTE MODE
You can customize the [REMOTE IN] terminal 
function.
Press ▲▼ to select [REMOTE MODE].
1  ) 
Press ◄► to switch [REMOTE MODE].
2  ) 
The setting will change as follows each time  
z
◄► is pressed.
DEFAULTUSERF SERIES
DEFAULT The pin assignment of the [REMOTE 
IN] terminal is used as the projector 
default setting. (
Æpage 85)
USER This is used for changing the settings 
for the REMOTE terminal.
Any settings you make for pins 2 
to 8 become valid once you press 
 button.
F SERIES Use the setting for F Series-compatible 
REMOTE terminal.
FUNCTION BUTTON
Three function buttons () on the 
remote control and the  button on the 
projector can be assigned to any frequent operations. 
They can be used as a useful shortcut button.
 buttons
Press any of the  
1  ) 
buttons on the remote control or the 
 button on the projector.
Press  button on the remote 
2  ) 
control or the projector to select a 
menu option (Main Menu, Submenu or 
Advanced Menu).
For the on-screen menu selection, see  
z“On-
screen menu ". (
Æpage 39)
Hold down any of the  buttons on the remote control 
or the  button on the 
projector more than 3 seconds.
Note
For details, see 
 
z “FUNCTION BUTTON” section of 
“PROJECTOR SETUP”. (
Æpage 66)
AUDIO SETTING
VOLUME 
J
Y
ou can adjust the volume of the built-in monaural 
speaker and VARIABLE AUDIO OUT terminal. ◄ Decrease
 
z
► Increase 
z
BALANCE 
J
You can adjust to hear the sound played equally 
through both right and left from VARIABLE AUDIO 
OUT, or shift the balance so more sound plays 
through the left or right side.
◄ More sound plays through the left side
 
z
► More sound plays through the right side 
z
IN STANDBY MODE 
J
You can switch on/off the sound output in standby 
mode.
OFF  No sound in standby mode.
 
z
ON  Output audio in standby mode. 
z
 
JAUDIO IN SELECT
A sound input terminal of [AUDIO IN 1], [AUDIO IN 
2], [AUDIO IN 3], [HDMI AUDIO IN] and [NETWORK 
AUDIO IN] can be selected.
Press ▲▼ to select a [AUDIO IN 
1  ) 
SELECT] terminal.
Press ◄► to switch [AUDIO IN 
2  ) 
SELECT].
The setting will change as follows each time the  
z
button is pressed.
AUDIO IN 1AUDIO IN 2AUDIO IN 3
NETWORK 
AUDIO IN *2HDMI AUDIO  IN *1
An input terminal having the HDMI port only
*1 : 
An input terminal having the network port only
*2 : 
AUDIO IN 1 Sound is output from AUDIO IN 1 
terminal when video of preset input 
terminal is projected.
AUDIO IN 2 Sound is output from AUDIO IN 2 
terminal when video of preset input 
terminal is projected.
AUDIO IN 3 Sound is output from AUDIO IN 3 
terminal when video of preset input 
terminal is projected.
HDMI  
AUDIO IN Sound is output from HDMI terminal 
when video of preset input terminal is 
projected.
NETWORK  AUDIO IN Sound is output from NETWORK 
terminal when video of preset input 
terminal is projected. 
						

							PROJECTOR SETUP menu
ENGLISH - 67
Settings
STATUS
Displays the status of the projector.
Press ▲▼ to select [STATUS].
1  ) 
Press  button.
2  ) 
Press ◄► to move to the next page.
3  ) 
INPUT Displays the input selection 
state.
SIGNAL NAME Displays the input signal name.
SIGNAL  
FREQUENCY Displays the frequency of the 
input signal.
PROJECTOR   RUNTIME Displays the projector runtime.
LAMP ECO:
 
z
LAMP POWER: Shows the 
lamp lighting time in ECO 
mode.
NORMAL:
 
z
LAMP POWER: Shows the 
lamp lighting time in NORMAL 
operation.
TOTAL:
 
z
Shows the total lamp lighting 
time.
INTAKE  
AIR TEMP. Displays the intake air 
temperature of the projector.
OPTICS   
MODULE TEMP. Displays the temperature inside 
the projector.
AROUND  
LAMP TEMP. Displays the temperature around 
the lamp of the projector.
NUMBER OF  
ENTRY SIGNAL Displays the number of 
registered signals.
REMOTE   STATUS Displays [REMOTE] control 
status.
PROJECTOR   TYPE Displays type of projector.
SERIAL  
NUMBER Displays the serial number of the 
projector.
LAMP UNIT  
MODEL NO. Displays the component number 
of the lamp unit.
LAMP SERIAL   NUMBER Displays the serial number for 
lamp.
MAIN VERSION Displays the main version of the 
firmware of the projector unit.
SUB VERSION Displays the sub version of the 
firmware of the projector unit.
NETWORK   VERSION Displays the network version of 
the projector unit.
EMULATE Displays the set emulate mode.
ON COUNT POWER ON TIMES :
 
z
Displays the number of times 
the power has been turned 
on.
LAMP ON :
 
z
Displays the number of times 
LAMP has been lit.
*1 : 
Lamp replacement time =    
    LAMP POWER [NORMAL] lighting time 
+ (LAMP POWER [ECO] lighting time x 2 ÷ 3)
DATE AND TIME
This lets you set the time zone and the current date 
and time for the projector’s internal clock.
 
JSetting the TIME ZONE
Press ▲▼ to select [DATE AND TIME].
1  ) 
Press  button.
2  ) 
Press ▲▼ to select [TIME ZONE].
3  ) 
Press ◄► to switch [TIME ZONE].
4  ) 
 
JAdjusting the date and time 
manually
Press ▲▼ to select [DATE AND TIME].
1  ) 
Press  button.
2  ) 
Press ▲▼ to select [ADJUST CLOCK].
3  ) 
Press  button.
4  ) 
The [ADJUST CLOCK] screen will be displayed. 
z
Press ▲▼ to select the item to be set, 
5  ) 
and press ◄► to set the local time.
Press ▲▼ to select [APPLY], and 
6  ) 
press  button.
This completes setting of the time. 
z 
						

							PROJECTOR SETUP menu
68 - ENGLISH
Settings
 
JAdjusting the date and time 
automatically
Press ▲▼ to select [DATE AND TIME].
1  ) 
Press  button.
2  ) 
Press ▲▼ to select [ADJUST CLOCK].
3  ) 
Press  button.
4  ) 
The [ADJUST CLOCK] screen will be displayed. 
z
Press ▲▼ to select [NTP 
5  ) 
SYNCHRONIZATION] and press ◄► to 
switch to [ON].
The setting will change as follows each time  
z
◄► is pressed.
OFFON
Press ▲▼ to select [APPLY], and 
6  ) 
press  button.
This completes setting of the time. 
z
Note
To set the date and time automatically, the projector must 
 
z
be connected to the network.
If synchronization with the NTP server fails just after 
 
z
[NTP SYNCHRONIZATION] is turned [ON], or if [NTP 
SYNCHRONIZATION] is turned [ON] while the NTP 
server is not set, [NTP SYNCHRONIZATION] will return 
to [OFF].
Access the projector via a web browser to set the NTP 
 
z
server.
SAVE ALL USER DATA
This saves various setting va lues as a backup to the 
internal memory of the projector.
Press ▲▼ to select [SAVE ALL USER 
1  ) 
DATA].
Press  button.
2  ) 
The [SECURITY PASSWORD] screen will be  
z
displayed.
Enter the password set for the 
3  ) 
[SECURITY PASSWORD].
The confirmation screen will be displayed. 
z
Press ◄► to select [OK], and press 
4  ) 
 button.
LOAD ALL USER DATA
This loads various setting values that were saved as a 
backup to the internal memory of the projector.
Press ▲▼ to select [LOAD ALL USER 
1  ) 
DATA].
Press  button.
2  ) 
The [SECURITY PASSWORD] screen will be  
z
displayed.
Enter the password set for the 
3  ) 
[SECURITY PASSWORD].
The confirmation screen will be displayed. 
z
Press ◄► to select [OK], and press 
4  ) 
 button.
Note
If this is executed, the projector enters a standby state in 
 
z
order to reflect the setting values. 
						

							PROJECTOR SETUP menu
ENGLISH - 69
Settings
INITIALIZE
This returns various setting values to their factory 
default settings.
Press ▲▼ to select [INITIALIZE].
1  ) 
Press  button.
2  ) 
The [SECURITY PASSWORD] screen will be  
z
displayed.
Enter the password set for the 
3  ) 
[SECURITY PASSWORD].
The [INITIALIZE] screen will be displayed. 
z
Press ▲▼ to select the desired 
4  ) 
initialize item.
ALL USER  
DATA All setting values including [ENTRY 
SIGNAL], [NETWORK/E-MAIL], and 
[LOGO IMAGE] are returned to their 
factory default values.
The projector enters a standby state 
in order to reflect the setting values.
ENTRY  
SIGNAL All setting values saved for each of 
the input signals are cleared.
To clear just some registered 
signals, perform the procedure 
described in 
“Deleting a registered 
data” (
Æpage 71).
NETWORK/  E-MAIL All setting values in [NETWORK 
SETUP] and [E-mail setup] settings 
will return to factory settings.
LOGO IMAGE The registered image data for 
[LOGO1] will return to factory 
settings.
Press  button.
5  ) 
The confirmation screen will be displayed. 
z
Press ◄► to select [OK], and press 
6  ) 
 button.
SERVICE PASSWORD
This function is used by a service  person. 
						

							70 - ENGLISH
Settings
TEST PATTERN menu
See  
z“Navigating through the menu ”  
(
Æpage 39).
See 
 
z“MAIN MENU” and “SUB MENU ”  
(
Æpage 40).
TEST PATTERN
Results of adjustment of the position, size and other 
factors are not reflected in test patterns. Ensure the 
input signal is displayed before performing various 
kinds of setting.
Press ◄► to select the required test 
1  ) 
pattern.
 
JCycle of displayed internal test 
patterns
The setting will change as follows each time ◄► 
is pressed.
MENU screen
+
FocusMENU screen +
Entry screen
MENU screen +
Color bars  
(HORIZONTAL) MENU screen
+
All white
MENU screen +
Color bars  
(VERTICAL) MENU screen
+
All black
MENU screen +
Window (inversion) MENU screen
+
Flag
MENU screen +
WindowMENU screen +
Flag (inversion)