Panasonic DLP Based Projector PT-DZ110XE PT-DS100XE PT-DW90XE Operating Instructions

							Technical Information
ENGLISH - 121
Appendix
REMOTE 2 IN terminal
Using the [REMOTE 2 IN] terminal provided on the connection terminals of\
 the main unit, it is possible to operate 
the projector from a control panel etc. furnished in a distant location \
where infrared remote control signal cannot 
be received.
 
JPin assignments and control
D-Sub 9-pin (Outside view) Pin No.
Signal name Open (H)Short (L)
GND —GND
POWER OFFON
RGB1Other RGB1
RGB2Other RGB2
VIDEOOtherVIDEO
S-VIDEO OtherS-VIDEO
DVIOther DVI
SHUTTER OFFON
RST/SETControlled by 
remote control Controlled by 
external contact
Attention
Be sure to short-circuit Pins 
 
z and  when controlling.
When pin 
 
z
 and pin  are short-circuited, the following buttons on the projector's control panel and on the remote control 
cannot be used.
 button,  button
In addition, the RS-232C commands and network functions that correspond \
to these functions cannot be used either.
When pin 
 
z
 and pin  are short-circuited and then any one of pins  to  is short-circuited to pin , the following buttons 
on the projector's control panel and on the remote control cannot be used.
 button,  buttons (RGB1, RGB2, DVI-D, SDI, VIDEO, S-VIDEO),  b\
utton
In addition, the RS-232C commands and network functions that correspond \
to these functions cannot be used either.
The above is explanation in the case where “REMOTE2 MODE” of “PROJECT OR SETUP” 
 
z (
Æpage
 85) is set to 
“STANDARD”.
S-VIDEO VIDEO
DVI-D
RGB2
Control panel located in a different room
LAMP
ON
RGB1 Standby
External control
Remote control/External control
Remote control
Projector set up in a meeting room 
						

							Technical Information
122 - ENGLISH
Appendix
Two window display combination list
Subwindow
Main window RGB1
RGB2
VIDEO input S- 
VIDEO  input DVI
HDMI*3
SDI
RGB 
input YP
BPR 
input RGB 
input YPBPR 
input
*1
Moving  image 
system
*2
RGB 
system
*1
Moving  image 
system
*2
RGB 
system
RGB1 RGB input
YPBPR input
RGB2RGB inputYPBPR input
VIDEO input
S-VIDEO input
DVIMoving image 
system *1
RGB  
system *2
HDMI Moving image 
system *1
RGB  
system *2
SDI *3
 : P IN P (Picture in Picture) combination is possible
 : P IN P (Picture in Picture) combination is impossible
Only 480p, 576p, 720/60p, 720/50p, 1 080/60i, 1 080/50i, 1 080/24sF, 1 080/24p, 1 080/25p, 1 080/30p, 
*1 : 
1 080/50p, and 1 080/60p are supported.
VGA (640 × 480) - WUXGA (1 920 × 1 200)
*2 : 
non-interlace signal, Dot clock frequency : 25 MHz - 162 MHz
(The WUXGA signals support only VESA CVT-RB (Reduced Blanking) signals.)
PT-DZ110XE/PT-DS100XE only
*3 : 
Note
If the horizontal resolution of the input signal of the sub window is 1 280 pixels or above, the picture quality of the sub 
 
z
window may be lowered.
Restoring the MENU LOCK PASSWORD to default
 Press  button for more than 2 seconds.
 Press ▼ for more than 2 seconds. 
						

							Technical Information
ENGLISH - 123
Appendix
List of compatible signals
The following table specifies the types of signals compatible with the projector.
Format :    V = VIDEO, S = S-VIDEO, D = DVI, H : HDMI, R : RGB, Y : YP
BPR, SDI Û
Mode Display resolution 
 
(dots) Scanning 
frequency Dot clock 
frequency  (MHz) Format PnP 
*1
H  
(kHz) V  
(Hz) RGB2DVI-D 
 
EDID1 DVI-D 
 
EDID2 DVI-D 
 
EDID3 HDMI
NTSC/NTSC4.43/  PAL-M/PAL60 720 × 480i
15.759.9 — V/S
PAL/PAL-N/SECAM 720 × 576i15.650.0 — V/S
525i (480i) 720 × 480i15.759.9 13.5 R/Y/SDI
625i (576i) 720 × 576i15.650.0 13.5 R/Y/SDI
525p (480p) 720 × 48331.559.9 27.0 D/H/R/Y
625p (576p) 720 × 57631.350.0 27.0 D/H/R/Y
1 125 (1 080)/60i *21 920 × 1 080i 33.860.0 74.3 D/H/R/Y/SDI
1 125 (1 080)/50i 1 920 × 1 080i28.150.0 74.3 D/H/R/Y/SDI
1 125 (1 080)/24p 1 920 × 1 08027.024.0 74.3 D/H/R/Y/SDI
1 125 (1 080)/24sF 1 920 × 1 080i27.024.0 74.3 D/H/R/Y/SDI
1 125 (1 080)/25p 1 920 × 1 08028.125.0 74.3 D/H/R/Y/SDI
1 125 (1 080)/30p 1 920 × 1 08033.830.0 74.3 D/H/R/Y/SDI
1 125 (1 080)/60p 1 920 × 1 08067.560.0 148.5 D/H/R/Y
1 125 (1 080)/50p 1 920 × 1 08056.350.0 148.5 D/H/R/Y
750 (720)/60p 1 280 × 72045.060.0 74.3 D/H/R/Y/SDI
750 (720)/50p 1 280 × 72037.550.0 74.3 D/H/R/Y/SDI
VESA400 640 × 400
31.570.1 25.2 D/H/R
640 × 400 37.985.1 31.5 D/H/R
VGA480 640 × 480
31.559.9 25.2 D/H/R
640 × 480 35.066.7 30.2 D/H/R
640 × 480 37.972.8 31.5 D/H/R
640 × 480 37.575.0 31.5 D/H/R
640 × 480 43.385.0 36.0 D/H/R
SVGA 800 × 600
35.256.3 36.0 D/H/R
800 × 600 37.960.3 40.0 D/H/R
800 × 600 48.172.2 50.0 D/H/R
800 × 600 46.975.0 49.5 D/H/R
800 × 600 53.785.1 56.3 D/H/R
MAC16 832 × 62449.774.6 57.3 D/H/R
XGA 1 024 × 768
39.650.0 51.9 D/H/R
1 024 × 768 48.460.0 65.0 D/H/R
1 024 × 768 56.570.1 75.0 D/H/R
1 024 × 768 60.075.0 78.8 D/H/R
1 024 × 768 65.581.6 86.0 D/H/R
1 024 × 768 68.785.0 94.5 D/H/R
1 024 × 768 80.0100.0 105.0 D/H/R
1 024 × 768 96.7120.0 130.0 D/H/R
MXGA 1 152 × 864
53.760.0 81.6 D/H/R
1 152 × 864 64.071.2 94.2 D/H/R
1 152 × 864 67.574.9 108.0 D/H/R
1 152 × 864 76.785.0 121.5 D/H/R
MAC21 1 152 × 87068.775.1 100.0 D/H/R
1 280 × 720 1 280 × 720
37.149.8 60.5 D/H/R
1 280 × 720 44.859.9 74.5 D/H/R
1 280 × 768 1 280 × 768
39.649.9 65.3 D/H/R
1 280 × 768 47.859.9 79.5 D/H/R
1 280 × 768 
*347.4 60.0 68.3 D/H/R
1 280 × 768 60.374.9 102.3 D/H/R
1 280 × 768 68.684.8 117.5 D/H/R
PT-DZ110XE/PT-DS100XE only
: 
Û 
						

							Technical Information
124 - ENGLISH
Appendix
ModeDisplay resolution 
 
(dots) Scanning 
frequency Dot clock 
frequency  (MHz) Format PnP 
*1
H  
(kHz) V  
(Hz) RGB2DVI-D 
 
EDID1 DVI-D 
 
EDID2 DVI-D 
 
EDID3 HDMI
1 280 × 800 1 280 × 800
41.350.0 68.0 D/H/R
1 280 × 800 49.759.8 83.5 D/H/R
1 280 × 800 
*349.3 59.9 71.0 D/H/R
1 280 × 800 62.874.9 106.5 D/H/R
1 280 × 800 71.684.9 122.5 D/H/R
MSXGA 1 280 × 96060.060.0 108.0 D/H/R
SXGA 1 280 × 1 024
52.450.0 88.0 D/H/R
1 280 × 1 024 64.060.0 108.0 D/H/R
1 280 × 1 024 72.366.3 125.0 D/H/R
1 280 × 1 024 78.272.0 135.1 D/H/R
1 280 × 1 024 80.075.0 135.0 D/H/R
1 280 × 1 024 91.185.0 157.5 D/H/R
1 366 × 768 1 366 × 768
47.759.8 84.8 D/H/R   
 *4    *4    *4    *4
1 366 × 768 39.649.9 69.0 D/H/R
SXGA+ 1 400 × 1 050
54.150.0 99.9 D/H/R
1 400 × 1 050 64.060.0 108.0 D/H/R
1 400 × 1 050 65.260.0 122.6 D/H/R
1 400 × 1 050 65.360.0 121.8 D/H/R
1 400 × 1 050 78.872.0 149.3 D/H/R
1 400 × 1 050 82.275.0 155.9 D/H/R
WXGA+ 1 440 × 900
55.959.9 106.5 D/H/R
1 440 × 900 46.349.9 86.8 D/H/R
UXGA60 1 600 × 1 20075.060.0 162.0 D/H/R
WSXGA+ 1 680 × 1 050
65.360.0 146.3 D/H/R
1 680 × 1 050 54.150.0 119.5 D/H/R
1 920 × 1 080 1 920 × 1 080
55.649.9 141.5 D/H/R
1 920 × 1 080 
*366.6 59.9 138.5 D/H/R
1 920 × 1 080 *667.2 60.0 173.0 R
WUXGA 1 920 × 1 200
61.849.9 158.3 D/H/R
1 920 × 1 200 
*374.0 60.0 154.0 D/H/R    *5    *5
1 920 × 1 200 *674.659.9 193.3 R
Where marked “
*1 : ” signals indicates in Plug and Play is compatible with EDID of projector. Unmarked 
signals in Plug and Play may also be compliant if input terminals are wr\
itten in the format list. Where Plug 
and Play is unmarked and nothing is written in the format list, difficulties in projecting image may occur even 
when computer and projector appear to have same resolution.
If a signal of 1 125 (1 035)/60i is input, it will be displayed as a signal of 1 125 (1 080)/60i.
*2 : 
VESA CVT-RB (Reduced Blanking) compatible.
*3 : 
PT-DW90XE only
*4 : 
PT-DZ110XE only
*5 : 
Some loss of data occurs to make projection easier.
*6 : 
Note
The number of display dots of the PT-DZ110XE is 1 920 × 1 200, and the number of display dots of the PT-DS100XE is 
 
z
1 400 × 1 050.
A signal of a different resolution than the above data is converted to the number of disp\
lay dots and then displayed.
The “i” appearing after the resolution indicates an interlaced sig\
nal.
 
z
Flicker (line flicker) may be caused in images if interlace is connected.
 
z 
						

							Specifications
ENGLISH - 125
Appendix
Specifications
Model No.PT-DZ110XE PT-DS100XE PT-DW90XE
Power supply AC220 V-240V    50 Hz/60 Hz
Power consumption 920 W
900 W
When [STANDBY MODE] is [ECO] : Approx. 0.3 W
When [STANDBY MODE] is [NORMAL] : Approx. 8 W
Amps 5.0 A 4.8 A
DLP chip Panel size
24.4 mm (0.96")  
(aspect ratio 16 : 10) 24.1 mm (0.95")  
(aspect ratio 4 : 3) 21.6 mm (0.85")  
(aspect ratio 16 : 9)
Display system Three-unit DLP chip, DLP type
Number of pixels 2 304 000 pixels 
 
(1 920 × 1 200 dots) × 3 1 470 000 pixels 
 
(1 400 × 1 050 dots) × 3 1 049 088 pixels 
 
(1 366 × 768 dots) × 3
Lens Option
Projection lamp 2 bulbs × 355 W UHM lamp
Optical output 
*110 600 lm (ANSI) 9 600 lm (ANSI)
*2
Applicable 
scanning 
frequencyFor RGB signal
H : 15 kHz - 100 kHz, V : 24 Hz - 120 Hz
PIAS (Panasonic Intelligent Auto Scanning) system
Dot clock frequencyLess than 162 MHz
For YP
BPR signal [480i]
[480p]
[720/50p]
[1 035/60i]
[1 080/60i]
[1 080/25p]
[1 080/30p]
[1 080/50p] H: 15.73 kHz, 
H: 31.5 kHz, 
H: 37.5 kHz, 
H: 33.75 kHz, 
H: 33.75 kHz, 
H: 28.13 kHz, 
H: 33.75 kHz, 
H: 56.25 kHz,  V: 59.94 Hz
V: 59.94 Hz
V: 50 Hz
V: 60 Hz
V: 60 Hz
V: 25 Hz
V: 30 Hz
V: 50 Hz [576i]
[576p]
[720/60p]
[1 080/50i]
[1 080/24p]
[1 080/24sF]
[1 080/60p]
H: 15.63 kHz, 
H: 31.25 kHz, 
H: 45 kHz, 
H: 28.13 kHz, 
H: 27 kHz, 
H: 27 kHz, 
H: 67.5 kHz,  V: 50 Hz
V: 50 Hz
V: 60 Hz
V: 50 Hz
V: 24 Hz
V: 48 Hz
V: 60 Hz
HD/SYNC, VD terminals are not compliant with 3 value composite SYNC.
 
z
For video signal 
(S-video  
included) H : 15.75 kHz/15.63 kHz, V : 50 Hz/60 Hz
For DVI-D/HDMI 
signal 480p, 576p, 720/60p, 720/50p, 1
 080/60p, 1  080/50p, 1  080/60i, 1  080/50i, 1  080/24sF, 1  080/30p, 
1 080/25p, 1 080/24p
Displayable resolution : VGA - WUXGA (non-interlace)
 
z
Dot clock frequency : 25 MHz - 162 MHz 
z
For SDI signal SMPTE259M compatible:  
[480i], [576i]
SMPTE292M compatible:   [720/60p], [720/50p], [1 035/60i], 
[1 080/60i], [1 080/50i], [1 080/25p], 
[1 080/24p], [1 080/24sF], [1 080/30p] —
Color system 7 standards (NTSC/NTSC4.43/PAL/PAL-N/PAL-M/SECAM/PAL60)
Screen size 1 778 mm - 15 240 mm (70" - 600") 
*3
Screen aspect ratio16 : 104 : 316 : 9
Projection scheme Menu-selectable from front/rear/ceiling mount, and floor mounting
Contrast ratio 10 000 : 1 (when [DYNAMIC IRIS] has been set to [3])
Terminals RGB1 IN
1 set, BNC × 5
[RGB signal]
0.7 V [p-p]
HD/SYNC
VD75 Ω (G-SYNC : 1.0 [p-p] 75 Ω)
TTL high impedance, automatic positive/negative polarity compatible
TTL high impedance, automatic positive/negative polarity compatible
[YP
BPR signal] Y : 1.0 V [p-p] Synchronization signal included, PBPR : 0.7 V [p-p] 75 Ω
RGB2 IN 1 set of high density, D-sub 15-pin (female)
[RGB signal]
0.7 V [p-p]
HD/SYNC
VD75 Ω (G-SYNC : 1.0 [p-p] 75 Ω)
TTL high impedance, automatic positive/negative polarity compatible
TTL high impedance, automatic positive/negative polarity compatible
[YP
BPR signal] Y : 1.0 V [p-p] Synchronization signal included, PBPR : 0.7 V [p-p] 75 Ω 
						

							Specifications
126 - ENGLISH
Appendix
Model No.PT-DZ110XE PT-DS100XE PT-DW90XE
Terminals VIDEO IN
1 set, BNC, 1.0 V [p-p] 75 Ω
S-VIDEO IN 1 set, Mini DIN 4-pin, Y: 1.0 V [p-p], C: 0.286 V [p-p] 75 Ω, compatible with S1 signal
DVI-D IN 1 set, DVI-D 24-pin (Single link), DVI 1.0 compatible, HDCP compatible
HDMI IN 1 set, HDMI 19-pin (HDCP/Deep color compatible)
SDI IN 1 set, BNC, Y/CB/CR/4 : 2 : 2, 10 bits
SMPTE259M/SMPTE292M compatible —
SERIAL IN/OUT 1 set, D-sub 9-pin, RS-232C compatible, computer control use
REMOTE 1  
IN/OUT 1 set, M3 pin jack, wired remote control use, multiple connection use
REMOTE 2 IN 1 set, D-sub 9-pin, external control use
LAN 1 set, RJ-45, network connection use, PJLink compatible, 10 Base-T/100Ba\
se-TX
Power cord length 3.0 m
Cabinet Moulded plastic
Dimensions Width : 530 mm (20 7/8"), Length : 200 mm (7 7/8"),  
Height : 548.5 mm (21 19/32") (540 mm (21 1/4") : not including surface projection parts)
Weight Approx. 24.0 kg (52.9 lbs.) 
*4
Operating environmentTemperature *5 : 0 °C to 45 °C
Humidity : 10 % to 80 % (no condensation)
Remote 
control Power supply
DC 3 V (AA/R6 battery × 2)
Operating range Approx. 30 m (98'5") (when operated directly in front of signal receptor)
Weight 134 g (4.7 ozs.) (including batteries)
Dimensions Width : 51 mm (2"), Length : 176 mm (6 15/16"), Height : 28 mm (1 3/32") 
Options Ceiling bracket
For high ceiling : ET-PKD310H
For low ceiling : ET-PKD310S
Ceiling Mount Attachment : ET-PAD310
Projection lens ET-D75LE6, ET-D75LE1, ET-D75LE2, ET-D75LE3, ET-D75LE4
ET-D75LE5, ET-D75LE8
ET-D75LE10, ET-D75LE20, ET-D75LE30
Lens Motor 
Cover ET-D75MC1
Replacement 
Lamp Unit ET-LAD310 (1 bulb), ET-LAD310W (2 bulbs)
Replacement 
filter unit ET-ACF310
Smoke Cut Filter ET-SFD310
Frame ET-PFD310
Measurement, measuring conditions and method of notation all comply with\
 ISO21118 international 
*1 : 
standards.
For details of video signals that can be projected using this projector, refer to 
*2 :  “List of compatible signals” 
(
Æpage  123).
If ET-D75LE5 is installed, screen size is 1 778 mm - 7 620 mm (70" - 300").
*3 : 
This is the average value. It may differ depending on each product.
*4 : 
When using this projector at high elevations 1 400 - 2 700 m (4 593 - 8 858 ft) sea level, temperature will be 
*5 : 
5 °C lower than this higher limit.   
When a Smoke Cut Filter is used, the ambient temperature is 0 °C to 35 °C. However, use at high altitudes 
is not possible.
The part numbers of accessories and separately sold components are subje\
ct to change without notice.
 
z 
						

							Specifications
ENGLISH - 127
Appendix
Specifications
Trademark AcknowledgementMicrosoft
 
z® and its logos, Windows®, Windows® XP, Windows Vista®, Windows® 7, and Internet Explorer® 
are the registered trademarks or trademarks of Microsoft Corporation in \
the United States and/or other 
countries.
Macintosh, Mac OS and Safari are the trademarks of Apple Inc. registered in the United States and other 
 
z
countries.
PJLink™ is a pending trademark in Japan, the United States, and other\
 countries and regions.
 
z
HDMI, the HDMI logo and High-Definition Multimedia Interface are the trademarks or registered trademarks  
z
of HDMI Licensing LLC.
Other types of names such as company names and product names appearing i\
n this instruction manual are 
 
z
trademarks or registered trademarks of their respective holders.
The ® and TM marks are not indicated in this instruction manual. 
Dimensions
About brand
8.5 (11/32")
540 (21 - 1/4")
462 (18 - 7/32")
530 (20 - 7/8")
200 (7 - 7/8")
100 (3 - 15/16")
468 (18 - 7/16")
26 (1 - 1/32") 
						

							128 - ENGLISH
Appendix
Ceiling mount bracket safeguards
When installing the ceiling mount bracket to the projector, install the accessory Drop-prevention bracket (Safety 
cables) to the projector.
(The projector will still be safe if they are not used, however they wi\
ll help prevent the possibility of accidents 
caused by the projector falling down if the screws happen to become loos\
e.)
Ceiling bracket :  For high ceiling : ET-PKD310H, For low ceiling : ET-PKD310S,  
Ceiling Mount Attachment : ET-PAD310
Installation work of the ceiling mount bracket should only be carried by\
 a 
qualified technician according to the following procedure.
Panasonic takes no responsibility for any losses or damage occurring as \
a result of using a ceiling mount  
z
bracket not manufactured by Panasonic, or if damage to the projector occ\
urs as a result of an inappropriate 
location used for installing the ceiling mount bracket, even if the projector’s warranty period has not yet expired.
Use a torque screwdriver or similar tool to tighten the screws. Do not u\
se tools such as electric screwdrivers or 
 
z
impact screwdrivers.
An unused ceiling mount bracket should be removed promptly by qualified technician.
 
z
Do not use the screw holes of the front leg adjusters for the projector \
installation. 
z
Do not attach the safety cable to the burglar hook port and suspend the \
projector on it. 
z
For how to install wire ropes to the ceiling, see the installation manua\
l for the ceiling mount bracket. 
z
For details, see the installation manual for the ceiling mount bracket. 
z
The part numbers of accessories and separately sold components are subje\
ct to change without notice. 
z
Attachment procedure
Turn the projector upside down and 
1  ) 
place it gently on a soft cloth.
Put the plain washer on the wire rope 
2  ) 
fixing screw.
Put the wire rope through the wire rope 
3  ) 
fixing screw.
Install the wire rope fixing screws to the 
4  ) 
projector and tighten them.
Install the wire ropes to the 2 places in a similar  
z
manner.
Wire rope fixing screw: M6 x L20.
Tightening torque of fixing screw: 4 ± 0.5 Nm
Attention
Do not use other than the provided Wire rope fixing screw (x2), washers (x4) and Safety cables (x2).
 
z
Install the wire ropes so that they do not sag between the installation \
portions on the body and those on the ceiling.
 
z
Ceiling bracket   
(Metal fitting attached to the ceiling mount bracket or projector  metal fitting for the ceiling mount bracket)
Wire rope
Positions to install 
wire ropes to body Plain washer
Wire rope fixing screw
Washer Please also attach the washer 
which is additional accessory to 
the ceiling mount.
Ceiling mount 
						

							ENGLISH - 129
Appendix
Index
A
About brand .................................. 127
Accessories  .................................... 17
ADVANCED MENU  ........................ 64
ASPECT  ......................................... 59
AUTO SETUP  ................................. 72
AUTO SETUP function  ...................48
AUTO SIGNAL ................................ 72
B
BACK COLOR ................................ 75
BLANKING  ..................................... 64
BRIGHTNESS  ................................ 54
BRIGHTNESS CONTROL  .............. 78
C
Ceiling mount bracket  ................... 128
CLAMP POSITION  ......................... 65
CLOCK PHASE  .............................. 61
COLOR  ........................................... 54
COLOR MATCHING  .......................69
COLOR TEMPERATURE  ...............55
Connecting AV equipment  .......................... 36
Before connection to the  projector  .............................. 35
Computers  .............................. 37
Connecting the power cord .............39
CONTRAST  .................................... 54
Control commands via LAN  .......... 116
CONTROL DEVICE SETUP  ........... 94
COOLING CONDITION  .................. 77
D
DATE AND TIME  ............................ 85
DIGITAL CINEMA REALITY  ........... 64
Dimensions  ................................... 127
Direct power off function  .................41
Display language  ............................ 68
DISPLAY LANGUAGE menu  ..........68
DISPLAY OPTION menu  ................69
DISPLAY SETTING  ........................ 93
DVI-D IN  ......................................... 73
DYNAMIC IRIS  ............................... 57
E
EDGE BLENDING ..........................65
F
FILTER COUNTER RESET  ............ 86
FILTER indicator  ........................... 109
FOCUS Adjusting  ................................. 42
FRAME DELAY  .............................. 67
FREEZE  ......................................... 75
Front leg adjusters  .......................... 34
FUNCTION  ............................... 48, 85
G
GAMMA .......................................... 56
GEOMETRY  ................................... 61
H
HDMI IN .......................................... 74
HIGH ALTITUDE MODE  .................76
I
Important Safety Notice  ....................2
INITIALIZE  ...................................... 87
INPUT RESOLUTION  ....................65
Input signal  ..................................... 47
INSTALLATION  .............................. 76
Internal test pattern .........................48
K
KEYSTONE .................................... 63
L
LAMP indicator ............................. 108
LAMP POWER  ............................... 78
LAMP RELAY  ................................. 77
LAMP SELECT  ............................... 77
LARGE SCREEN CORRECTION ..... 70
LENS CALIBRATION  .....................86
Lens position  .................................. 43
List of compatible signals  ............. 123
LOAD ALL USER DATA  .................. 87
M
MAIN MENU  ................................... 51
Managing the indicated problems ... 108
MENU LOCK  .................................. 93
MENU LOCK PASSWORD  ..........122
Menu Navigation ............................. 50
N
Navigating through the menu  ......... 50
NETWORK menu  ...........................95
NOISE REDUCTION  ......................57
NO SIGNAL SHUT-OFF  ................. 85
O
On-screen display .....................47, 74
P
Picture Aspect ratio .........................49
PICTURE menu  .............................. 53
PICTURE MODE  ............................ 53
P IN P function  ................................ 88
P IN P menu  ................................... 88
PJLink protocol  ............................. 115
POSITION menu  ............................ 59
Powering off the projector  ...............41
Powering up the projector ...............40
Precautions with regard to safety  ..... 9
Projecting ........................................ 42
Projection lens  ................................ 38
Projection method ...........................22
Projector body  ................................ 19
PROJECTOR ID  ............................. 76
PROJECTOR SETUP menu  ..........76
R
RASTER POSITION  ....................... 67
REMOTE 2 IN terminal  .................121
REMOTE2 MODE  ..........................85
Remote control  ............................... 18
Replacement  ................................ 110
RGB IN  ........................................... 73
RS-232C  ......................................... 83
S
SAVE ALL USER DATA .................. 87
SCHEDULE  .................................... 82
SCREEN SETTING  ........................70
Screen size and throw distance ......23
SDI IN  ............................................. 74
SECURITY menu  ...........................92
SECURITY PASSWORD  ................92
Selecting the input signal ................42
Serial terminal............................... 118
SERVICE PASSWORD  ..................87
Setting projector ID number to   
remote control  ............................. 21
Setting up  ....................................... 22
SHARPNESS  ................................. 57
SHIFT  ............................................. 59
SHUTTER function  .........................47
SIGNAL LIST  .................................. 90
Registering a signal  ................ 90
SIGNAL LIST menu  ........................90
Specifications  ............................... 125
STANDBY MODE  ...........................82
STARTUP LOGO  ............................ 75
STATUS  .......................................... 84
STATUS function  ............................ 47
Sub memory  ................................... 91
SUB MENU  ..................................... 51
SYSTEM DAYLIGHT VIEW  ............ 56
SYSTEM SELECTOR  ....................58
T
Technical Information ....................115
TEMP indicator  ............................. 109
TEST PATTERN  ............................. 89
TEST PATTERN menu  ...................89
TINT  ................................................ 54
Troubleshooting  ............................ 113
Two window display combination .... 122
W
WAVEFORM MONITOR  .................71
Wired remote control  ...................... 21
Z
ZOOM ............................................. 60