Home
>
Panasonic
>
Projector
>
Panasonic DLP Based Projector PT-DZ110XE PT-DS100XE PT-DW90XE Operating Instructions
Panasonic DLP Based Projector PT-DZ110XE PT-DS100XE PT-DW90XE Operating Instructions
Have a look at the manual Panasonic DLP Based Projector PT-DZ110XE PT-DS100XE PT-DW90XE Operating Instructions online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 10737 Panasonic manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
SIGNAL LIST menu ENGLISH - 91 Settings Managing the sub memory list You can restore the sub memory data when using signals from the same input source. Sub memory data contains the setting information of screen and image adjustments, such as BRIGHTNESS, CONTRAST or ASPECT. Registering the current settings J to the list In the normal screen (when the menu 1 ) is not displayed), press ◄► button. The signal must be registered before creating a z sub memory data of the signal. Displays the list of corresponding sub memory z data to the signal. Press ▲▼◄► to select the required 2 ) sub memory data. Press button. 3 ) The [ SIGNAL NAME] screen will be displayed. z Press button. 4 ) Note For renaming a registered data, follow the same z procedure (steps 4 - 5) of “Renaming a registered data” ( Æpage 90). JDisplaying the sub memory list and restoring the settings In the normal screen (when the menu 1 ) is not displayed), press ◄► button. The [SUB MEMORY LIST] screen will be z displayed. Press ▲▼◄► to select the required 2 ) sub memory data, and press button. The [REGISTERED SIGNAL STATUS] screen z will be displayed. Press button. 3 ) Restores the settings in the data. z Deleting a sub memory data J In the normal screen (when the menu 1 ) is not displayed), press ◄► button. The [SUB MEMORY LIST] screen will be z displayed. Press ▲▼◄► to select the required 2 ) sub memory data, and press button. The [REGISTERED SIGNAL STATUS] screen z will be displayed. Press button. 3 ) Displays the [SUB MEMORY LIST] with z change. You can return to the previous step by pressing z button.
SECURITY menu 92 - ENGLISH Settings SECURITY menu See “Navigating through the menu” z (Æpage 50). See “MAIN MENU” and “SUB MENU” z (Æpage 51). When you apply to the [SECURITY] menu z before you change the password to your original, perform to input the following factory default password operation. Press ▲►▼◄▲►▼◄ and button. Attention When you apply to the SECURITY menu after you z change the password to your original in the [SECURITY PASSWORD CHANGE] menu, input the original password operation. Note Only asterisks * will appear on the screen to represent z the actual characters of the password when the password is entered. SECURITY PASSWORD The [SECURITY PASSWORD] screen can be displayed when the power has been turned on. If the correct password is not entered, operations other than using button and button and adjusting the lens will not be possible. Press ▲▼ to select [SECURITY 1 ) PASSWORD]. Press ◄► to switch [SECURITY 2 ) PASSWORD]. The setting will change as follows each time z ◄► is pressed. OFFON OFF Deactive ON Active Note [PASSWORD] is set to [OFF] by default and when z initialized. Change the SECURITY PASSWORD regularly and make z it uneasy to guess. The security password becomes valid when setting of z the security password is turned [ON] and then the MAIN POWER switch is turned off. SECURITY PASSWORD CHANGE The password can be changed. Press ▲▼ to select [SECURITY 1 ) PASSWORD CHANGE]. Press button. 2 ) The [SECURITY PASSWORD CHANGE] z screen will be displayed. Press ▲▼◄► and numeral keys to 3 ) set the password. Up to 8 buttons can be set as the password. z Press button. 4 ) For the purposes of confirmation, 5 ) enter the password again. Press button. 6 ) Note Only asterisks * will appear on the screen to represent z the actual characters of the password when the password is entered. If the password input second does not match with the z password input first, an error message is displayed. In this case, input the correct password again. When numerals are used in the SECURITY PASSWORD, z initialization of the security password will be necessary if the remote control is lost. For the method of initialization, consult your dealer.
SECURITY menu ENGLISH - 93 Settings DISPLAY SETTING You can set your original text, such as company name or URL information, to display regularly on the projected image while projecting. Press ▲▼ to select [DISPLAY 1 ) SETTING]. Press ◄► to switch [DISPLAY 2 ) SETTING]. The setting will change as follows each time z ◄► is pressed. OFFTEXTLOGO1 OFF The text display is disabled. TEXT The text display is enabled. LOGO1 The picture registered by the user will be projected. Note Separate software [Logo Transfer Software] is required in z order to create the pictures to use for [LOGO1]. Consult your dealer. TEXT CHANGE You can enter your original text to be displayed when [DISPLAY SETTING] is turned [TEXT]. Press ▲▼ to select [TEXT CHANGE]. 1 ) Press button. 2 ) The [TEXT CHANGE] screen will be displayed. z Press ▲▼◄► to select characters 3 ) and press button to input them. Press ▲▼◄► to select [OK], and 4 ) press button. The text is now changed. z MENU LOCK You can lock button function and the password will be asked to display the menu every time. Press ▲▼ to select [MENU LOCK]. 1 ) Press ◄► to switch [MENU LOCK]. 2 ) The setting will change as follows each time z ◄► is pressed. OFFON OFF Deactivate the [MENU LOCK] system. ON Activate the [MENU LOCK] system. Note Once [MENU LOCK] is set to [ON], you cannot use z button unless you input the correct password. The [MENU LOCK] is set to [OFF] by default and when z initialized. The unlock state is maintained until the projector is set to z the standby mode. MENU LOCK PASSWORD You can change the password for [MENU LOCK] system to your original. Press ▲▼ to select [MENU LOCK 1 ) PASSWORD]. Press button. 2 ) The [MENU LOCK PASSWORD] screen will be z displayed. Press ▲▼◄► to select characters 3 ) and press button to input them. Press ▲▼◄► to select [OK], and 4 ) press button. To stop, select [CANCEL]. z Attention The factory default password is “AAAA”. z When the projector is initialized, the password will be z changed to the factory default setting, “AAAA”. Change the MENU LOCK PASSWORD regularly and z make it uneasy to guess.
SECURITY menu 94 - ENGLISH Settings CONTROL DEVICE SETUP Control from the remote control and main unit controls can be restricted. Press ▲▼ to select [CONTROL 1 ) DEVICE SETUP]. Press button. 2 ) The [CONTROL DEVICE SETUP] screen will z be displayed. Press ▲▼ to select [CONTROL 3 ) PANEL] or [REMOTE CONTROLLER]. Press button. 4 ) [ zCONTROL PANEL] screen or [REMOTE CONTROLLER] screen will be displayed. JCONTROL PANEL Restriction of control from the main unit controls z can be set. ENABLE Enables control from the main unit controls. DISABLE Disables control from the main unit controls. JREMOTE CONTROLLER Restriction of control from the remote control z can be set. ENABLE Enables control from the remote control. DISABLE Disables control from the remote control. Press ▲▼ to select [ENABLE] or 5 ) [DISABLE], and press button. The confirmation screen will be displayed. z Press ◄► to select [OK], and press 6 ) button. Note If an attempt is made to control the projector from the z remote control or main unit controls when [DISABLE] is set, the [SECURITY PASSWORD] screen appears. To change a setting, enter the security password and change the operation setting. The [SECURITY PASSWORD] screen disappears if z button is pressed or no operation is performed for 10 seconds. If you [DISABLE] both of the [CONTROL PANEL] and z [REMOTE CONTROLLER] buttons, you cannot return to the standby mode. Use this function with utmost care. If a setting is reflected, the on-screen menu disappears. z To continue operation, press button to display the main menu.
NETWORK menu ENGLISH - 95 Settings NETWORK menu See “Navigating through the menu” z (Æpage 50). See “MAIN MENU” and “SUB MENU” z (Æpage 51). NETWORK SETUP Make the initial network settings before using the network connection. Press ▲▼ to select [NETWORK 1 ) SETUP]. Press button. 2 ) The [NETWORK SETUP] screen will be z displayed. Press ▲▼ to select an item, and 3 ) change the setting according to the instructions. PROJECTOR NAME (Display of host name and setting) Change as needed when using a DHCP server. DHCP (DHCP client function) Set [DHCP] item to [ON] when to acquire an IP address automatically using the DHCP server. Set to [OFF] if [DHCP] server is not used. Enter the IP address if DHCP server is not used. IP ADDRESS (Display of IP address and setting)Enter the IP address if DHCP server is not used. SUBNET MASK (Displaying and setting the subnet mask)If not using a DHCP server, enter the subnet mask. DEFAULT GATEWAY (Display of gateway address and setting)Enter the gateway address if DHCP server is not used. STORE Save the current network settings. Press ▲▼ to select [STORE], and 4 ) press button. Note Before using the DHCP server, make sure the DHCP z server is already functioning. For details of IP address, subnet mask, and gateway, ask z the network administrator. NETWORK CONTROL This sets the network control method. Press ▲▼ to select [NETWORK 1 ) CONTROL]. Press button. 2 ) The [NETWORK CONTROL] screen will be z displayed. Press ▲▼ to select items, and press 3 ) ◄► to change the setting. WEB CONTROL Set this to [ON] when you want to perform control with the Web browser. PJLink CONTROL Set this to [ON] when you want to perform control with the PJLink protocol. COMMAND CONTROL Û Set to [ON] to control using the control command via the serial terminal. ( Æpage 120) COMMAND PORT Set the port number used for the command control. STORE Save the current network control settings. If settings have been made without an : Û administrator password of the Web browser control, add 2-byte “00” instead of STX, and a line- feed code (0Dh) instead of ETX. If settings have been made with an administrator password of the Web browser control, add a 32-byte hash value and “00” instead of STX and a line-feed code (0Dh) instead of ETX. The hash value is created by MD5 combining “admin1:”, password, “:” and random numbers. The random numbers are 8-byte values sent from the projector when connecting. NETWORK STATUS This displays the network status of the main unit. Press ▲▼ to select [NETWORK 1 ) STATUS]. Press button. 2 ) The [NETWORK STATUS] screen will be z displayed.
NETWORK menu 96 - ENGLISH Settings Network connections The projector is equipped with network functions, and web browser contro\ ls can be used to carry out the following operations from a computer.Projector settings and adjustments z Projector status display z Transmission of E-mail messages if there is a problem with the projector z Note A LAN cable is required to use the network function. z A Web browser is required to use this function. Make sure that a Web browser is available in the system. z Supported OS: Windows XP/Windows Vista/Windows 7, Mac OS X v10.4/v10.5/v10.6. z Supported browser: Internet Explorer 6.0/7.0/8.0, Safari 2.0/3.0/4.0 (Mac OS). z To use the E-mail function, communication with E-mail server must be esta\ blished. Make sure that E-mail z feature is available in your system. Use a straight insulated LAN cable which supports category 5 or above. z The length of LAN cable must be 100 m or shorter. z Name and function of network function parts J Attention If the LAN terminal is touched by electrostatically charged hands (or b\ ody), failure may be caused by the discharge of static z electricity. Be careful not to touch metallic part of LAN terminal or LAN cable. Connect indoor equipment to the LAN. z LAN cable (straight) Projector LAN switch LAN cable (straight) Computer LAN10/100 lamp (yellow) This lights when a 100BASE-TX connection is established. LAN terminal (10BASE-T/100BASE-TX) Connect LAN cable here. LAN LINK/ACT lamp (green) This lights when a LAN cable is connected and flashes when signals are being received or sent.
NETWORK menu ENGLISH - 97 Settings Accessing from the Web browser Activate the Web browser in the personal computer. 1 ) Enter the IP address set by the projector into the URL input field of the Web browser. 2 ) Enter your “User name” and “Password”. 3 ) The factory default settings are user1 (user privileges) or admin1 (a\ dministrator privileges) for the user z name and panasonic (lowercase letters) for the password. Click [OK] to display the Projector status page. 4 ) Note Avoid activating two or more Web browser simultaneously to work out setting or control actions. z Change the password first of all. z Administrator privileges enable the use of all functions. User privilege\ s enable the use of only “Projector status”, “Error z information”, “Network status”, “Basic control”, and “\ Change password”. If the password is incorrectly entered three times in a row, the lock is set for several minutes. z
NETWORK menu 98 - ENGLISH Settings Change Password page J Click [Change password]. Administrator User Administrator mode Q Administrator account z Account Current user name input field Current password input field New user name input field New password input field New password input field (re-enter for confirmation) Button for executing password change User account z Account New user name input field New password input field New password input field (re-enter for confirmation) Button for executing password change User mode Q A user can change password only. Current password input field New password input field New password input field (re-enter for confirmation) Button for executing password change
NETWORK menu ENGLISH - 99 Settings Basic control page J To move from another page, click [Projector control], then [Basic control\ ]. Page selection tabs Click these to switch pages. This displays the on-screen status. It is displayed even if the on-screen display of the projector is set to off. Monitor information button Click this item, and the status of the projector is displayed. Detailed set up button Click this item to display the advanced settings page. Change password button Power On/Off control SHUTTER control OSD (On-screen Display) display/nondisplay System type switching Use these to select the input signals.
NETWORK menu 100 - ENGLISH Settings Detail control page J Click [Projector control], then [Detail control] to display the Detail c\ ontrol page. Pressing these buttons controls the projector and updates the on-screen description on the right of the control page when control is finished. Lens adjustment Test pattern display This button updates the on-screen description on the right of the control page with the latest information. Menu display Projector status page J Click [Status], then [Projector status] to display the Status informatio\ n page. This page displays the projector statuses established for the items show\ n below. Displays the type of projector. Displays the firmware version of the projector main unit. Displays the input switching status. Displays temperature of projector’s intake air. Displays temperature inside the projector. Displays the AROUND LAMP TEMPERATURE. Displays the lamp lit hours. Displays the REMAINING FILTER QUANTITY. Displays self-diagnosis information. Displays used hours of the projector.