Panasonic DLP Based Projector PT-D7700U PT-DW7000U Operating Instructions

71
Option settings
OPTION
  PROJECTOR ID 2
  SETTING FRONT-F
  LAMP SELECT DUAL
  LAMP POWER HIGH
  RS232C SETTING
  OSD POSITION 2
  SYSTEM INFORMATION
  COLOR MATCHING OFF
  VIDEO SETTING
  AUTO SETUP
     :MENU SELECT
     :CHANGE
MAIN MENU
         PICTURE
         POSITION
         ADVANCED MENU
         LANGUAGE
         OPTION
         TEST PATTERN
         SIGNAL LIST
         SECURITY
     :MENU SELECT
ENTER:SUB MENU
Press the “ENTER” button.
The OPTION screen will be displayed.
Select...

72
Option settings
A: Floor mount front projection (Front – Floor mount)
D: Ceiling mount rear projection (Rear – Ceiling mount) C: Floor mount rear projection (Rear – Floor mount)B: Ceiling mount front projection (Front – Ceiling mount)
Select the setting by displaying the on-screen indications using buttons of the remote control or the control panel on
the main unit.
Procedure of setting
OPTION
  PROJECTOR ID 2
  SETTING FRONT-F
  LAMP SELECT DUAL
  LAMP POWER HIGH
  RS232C SETTING
  OSD POSITION 2...

73
Lamp select
Two internal lamps in the projector can be used either
in “DUAL” or “SINGLE” mode depending on users
needs or viewing conditions.
In the “SINGLE” mode, the projector may automatically
switches between one lamp and the other, or one of
the lamps can be specified.
“LAMP 1”: One lamp illuminates.
(Lamp Unit 1 is always used)
“LAMP 2”: One lamp illuminates.
(Lamp Unit 2 is always used)
“SINGLE”: One of the lamps illuminates.
(The lamp with shorter operating hours is
automatically selected)...

74
Option settings
Position of on-screen
indications
The user can specify the position of the on-screen
indications
“1”: Top left of the screen
“2”: Left center of the screen
“3”: Bottom left of the screen
“4”: Top center of the screen
“5”: Center of the screen
“6”: Bottom center of the screen
“7”: Top right of the screen
“8”: Right center of the screen
“9”: Bottom right of the screen
OSD POSITION1
2
8
9
System information
Displays the system information of the projector.
• Pressing the “ENTER” button...

75
Adjusting color matching
When multiple sets are used simultaneously, this projector allows the user to correct the difference of colors among
the sets.
Procedure of adjustment
OPTION
  PROJECTOR ID 2
  SETTING FRONT-F
  LAMP SELECT DUAL
  LAMP POWER HIGH
  RS232C SETTING
  OSD POSITION 2
  SYSTEM INFORMATION
  COLOR MATCHING 3COLORS
  VIDEO SETTING
  AUTO SETUP
     :MENU SELECT        :CHANGE
ENTER:SUB MENU
Press the “MENU” button.
The MAIN MENU screen will be displayed.
Select “OPTION” with the...

76
Option settings
MEASURE MODE
  MEASURED DATA
  TARGET DATA
  AUTO TESTPATTERN ON
  
  
  
  
  
     :MENU SELECT
ENTER:SUB MENU
MEASURE MODE
  MEASURED DATA
  TARGET DATA
  AUTO TESTPATTERN ON
  
  
  
  
  
MEASURE MODE
  MEASURED DATA
  TARGET DATA
  AUTO TESTPATTERN ON
  
TARGET DATA
  R, G, B
  Cy, Mg, Ye, Wh
  
  
TARGET DATA: R, G ,B
  R x 0.630
   y 0.340
  G x 0.310
   y 0.595
  B x 0.155
   y 0.070
     :MENU SELECT
     :ADJUST
MEASURED DATA
  Bk Y 5
   x 0.313
   y 0.329
  R Y 2126
   x...

77
Automatic adjustment
(Only for RGB input)
Use this setting when adjusting a specific or oblong
(16:9, etc.) signal.
Press the MENU button.
The MAIN MENU screen will be displayed.
Select “OPTION” with the 
buttons.
Press the ENTER button.
The OPTION screen will be displayed.
Using the  buttons, select “AUTO
SETUP”.
Press the ENTER button.
The AUTO SETUP screen will be displayed.
Using the  buttons, switch to the
desired mode.
“DEFAULT”: to receive signals of which image
aspect is 4:3 or 5:4
“WIDE”: to...

78
Option settings
Fan control
When using the projector over 1 400 m (4605.3)
above sea level, set to “HIGHLAND”.
FAN CONTROL NORMAL
HIGHLAND
OPTION
  OUTPUT RESOLUTION SXGA+
  AUTO SIGNAL ON
  FAN CONTROL NORMAL 
  P IN P OFF
  FUNC1 P IN P
  PASSWORD
     :MENU SELECT    
     :CHANGEOPTION
  OUTPUT RESOLUTION SXGA+
  AUTO SIGNAL ON
  FAN CONTROL NORMAL 
  P IN P OFF
  FUNC1 P IN P
  PASSWORD
     :MENU SELECT    
     :CHANGE
Output resolution
(D7700U only)
Pictures projected onto a screen (for SXGA)...

79
P IN P
This item is used to set the condition of the Picture-In-
Picture.
Main window
Subwindow
Use the  buttons to select OFF,
USER 1, USER 2, or USER 3.
When selecting an option other than OFF, the submenu
can be displayed by pressing the ENTER button.
• Main window:
The input terminal for the main window is
displayed. The  buttons can be used to
select the input terminal. 
Size: The user can specify the display size of the
main window between 10% and 100%.
Position: The user can specify the display...

80
Option settings
Setting FUNC1
The user can specify the function of the “FUNC 1”
button on the remote control.
“P IN P”:  Enables setting of P IN P to OFF,
USER 1, USER 2, or USER 3.
(refer to page 79).
“LAMP POWER”: Enables the lamp power to be
switched between high and low
(refer to page 73).
“SIZE”:  Enables the picture size to be
selected (refer to page 58).
FUNC1
LAMP POWER
SIZE
P IN P
ET-MD95SD1
ET-MD95SD2
ET-MD95SD3
ET-MD75DV
ET-MD75NT
AUX
AUXET-MD95RGB
RGB1
Subwindow
Main window
RGB2 RGB1
RGB2...