Panasonic DLP Based Projector PT CW230 Operating Instructions

Setting up
ENGLISH - 21
Getting Started
 JProjection distance for PT-CX200E
(All measurements below are approximate and may differ slightly from the actual measurements.)
Projection sizeFor 4:3 aspect ratioFor 16:9 aspect ratio
Screen diagonal (SD)LALA
1.27 m(50")--24.8 cm(0.81')35.5 cm(1.17')
1.40 m(55")25.1 cm(0.82')25.2 cm(0.83')27.7 cm(0.91')38.0 cm(1.25')
1.52 m(60")27.7 cm(0.91')26.6 cm(0.87')30.6 cm(1.00')40.5 cm(1.33')
1.78 m(70")33.0...

Setting up
22 - ENGLISH
Getting Started
Adjusting front adjustable feet
Lift the front of the projector and rotate the adjustable feet to a proper height and tilt.
You can turn the front adjustable feet to extend them. You can turn them in the opposite direction to contract 
them.
(You can adjust the projection angle vertically.)
Attention
Heated air comes out of the air exhaust port while the lamp is lit. Do not touch the air exhaust port directly when you adjust  z
the front adjustable feet.
If...

ENGLISH - 23
Getting Started
Connections
Before connecting to the projector
Read carefully the instruction manual for the device to be connected. z
Turn off the power switch of the devices before connecting cables. z
If any connection cable is not supplied with the device, or if no option\
al cable is available for connection of the  z
device, prepare a necessary system connection cable to suit the device.
Video signals containing too much jitter may cause the images on the screen to randomly wobble or...

24 - ENGLISH
Basic Operation
Powering ON/OFF
Connecting the power cord
Be sure to insert the attached power cord securely to its base to preven\
t it from coming off.
Power cord holder J
A power cord holder is designed to prevent the AC power cord from coming off the projector.
Please insert the power cord into the power cord holder correctly as Pic\
ture (1) shown:
Attaching  J
Attach the AC power cord with the power cord clamp to the projector by following these steps. 
Plug the power cord with the...

Powering ON/OFF
ENGLISH - 25
Basic Operation
ON(G)/STANDBY(R) indicator
The  indicator informs you the status of the power. Confirm the status of the  indicator before operating the projector.
ON(G)/STANDBY(R) indicator
Indicator statusStatus
No illumination or flashingThe power cord is unplugged.
RED
LitThe power cord is plugged.
The projector is in stand-by mode, after the cooling is completed.
Flashing
The projector is cooling down. The projector cannot be turned on until cooling is 
completed and the...

Powering ON/OFF
26 - ENGLISH
Basic Operation
Complete peripheral connections (with a 1 ) 
computer, VCR, etc.) before turning on the 
projector.
Connect the projector’s AC power cord into an 2 ) 
AC outlet. The  indicator 
lights red. 
Press the 3 )  button on the control panel or 
the remote control. The  
indicator lights green and the cooling fans start 
to operate. The preparation display appears on 
the screen and the count down starts.
After the countdown, the input source that was 4 ) 
selected...

Powering ON/OFF
ENGLISH - 27
Basic Operation
Enter a PIN code
PIN Code Input Dialog BoxPress ▲▼ to enter a number. Press ► to fix the 
number and move the red frame pointer to the next 
box. The number changes to . If you fixed an 
incorrect number, use the ◄ button to move the 
pointer to the number you want to correct, and then 
enter the correct number.
Repeat this step to complete entering a four-digit 
number.
After entering the four-digit number, move the pointer 
to “Set”. Press the  button so...

Powering ON/OFF
28 - ENGLISH
Basic Operation
Press the  button on the control panel or  
the remote control, and Power off? appears on 
the screen.
Press the  button on the control panel or  
the remote control again to turn off the projector.  
The  indicator starts to 
blink red, and the cooling fans keep running. 
At this time, you can unplug the AC power cord 
even if the fans are still running.
When the projector has cooled down enough, the 3 ) 
 indicator stops blinking 
and you can turn on the...

ENGLISH - 29
Basic Operation
Projecting
Check the connections of the peripheral devices and connection of the po\
wer cord (Æpage 24) and switch on the 
power (Æpage 26) to start the projector. Select the image and adjust the state of the image.
Selecting the image
Select an input signal.
The image selected with the , , , ,\
 , or 
 button is projected (Æpages 38-39).
Attention
Images may not be projected properly depending on the connected device and DVD, video tape, etc. to be played. Set a  z
system...

Projecting
30 - ENGLISH
Basic Operation
For Viewing 3D Contents
To view 3D images, you need to prepare at least the 3D active shutter gla\
sses, 3D content and 3D reproducing 
equipment. For example, as for computer, when transmitting 3D signals from a computer to the projector, you 
also need to install the graphic card which has the capability to sequentially output the 3D frames at 120Hz and 
software in the computer. The 3D signal type which the projector can accept is frame sequential only. Other 3D...