Panasonic DIla PROJECTOR PT-D995U Operating Instructions

Controls and Features (cont.)
Control Panel
STAND BYLAMP indicator
ON: After the light-source lamp has been used for
more than approx. 900 hours.
Blinking : Replace the lamp. Refer to “Replacing the Light-
Source Lamp” on page 50.
LAMP
TEMPTEMP indicator
ON :  The temperature inside the projector is abnormallyhigh.
EMERGENCY
VIDEO
While the TEMP indicator is on (during abnormal temperature), thepower is automatically cut off, and an emergency mode is shown
(with the EMERGENCY indicator blinking)....

Controls and Features (cont.)
Control Panel (Cont.)
STAND BYLAMP
TEMP
EMERGENCY
VIDEO
COMPUTER SETTING
QUICK ALIGN. button
While a menu screen is shown, use this button to adjust
the values for the item selected. When no menu is shown,
the quick alignment function works.
When a menu is shown
+button: The value for the selected item increases.
-button: The value for the selected item decreases.
When no menu is shown
Press the +button and -button at the same time:
QUICK ALIGNMENT is displayed on the screen...

Controls and Features (cont.)
Connector Panel
Y/C (S video) input terminal (Mini DIN 4 pin)
Connect this terminal to the S video output terminal of a
video deck, etc.
VIDEO (composite video) input terminal (BNC)
Connect this terminal to the composite video output terminal
of a video deck, etc.
AUDIO OUT (audio output) terminal (stereo mini jack)
Of input signals inputted to the projector, the audio signal
of the device being projected is output. Volume should be
adjusted using the VOL. (+/-) buttons on...

Controls and Features (cont.)
Connector Panel (Cont.)
COMPUTER IN (computer input) -2 terminals (BNC)
These are input terminals for analog RGB signals, verticalsync (V) signals, and horizontal sync (H) signals/composite
signals(Cs). Devices which have analog RGB signal output
terminals can be connected.
*Input of external sync signals is automatically
detected.
Detection of H/D signals or Cs signals causes automatic
switch to external sync. The priority order is H/D > Cs.
When computer-related signals...

Controls and Features (Cont.)
Remote Control Unit
Remote control’s signal transmitter
COMPUTER button
Use this button to select the devices connected to the
projector’s COMPUTER IN (computer input) -1 and -2 input
connector/terminals. Each time you press the button, the
selection changes as follows:
COMPUTER 1COMPUTER 2
VIDEO button
Use this button to select the devices such as a video
connected to the projector’s AV IN (AV input) terminals. Each
time you press the button, the selection changes as...

Controls and Features (cont.)
Installing Batteries
Install batteries in the remote control. If the remote control has started to work erratically, replace the batteries.
Open the back cover.Precautions for using batteries
While pushing on the back cover, slide it in the direction
of the arrow.
If batteries are used incorrectly, they may crack or
leak liquid. This could cause a fire, burn, malfunction,
or staining or damaging the surrounding.
Beware of the following:
Do not mix new and old batteries.
Do...

Installing the Projector
Precautions for Installation
Do not install the projector in places where :There is much water, humidity or dust.
The projector may be subjected to oil smoke or cigarette smoke.
The surface is soft, such as a carpet or cushion.
The projector may be subjected to direct sunlight.
Temperature is high or humidity is low.
Allowable operation temperature range: + 5°C to + 35°C (41°F to 95°F)
Allowable relative humidity range: 20% to 80% (no condensation)
Allowable storage temperature...

Installing the Projector (Cont.)
Projection Distance and Screen Size
The projector’s projection lens is a zoom lens of about 1.5 x. The screen size at the maximum enlargement is 1.5
times that of the minimum size.
The projection distance that can be focused is 2.5 to 20 m. Install the projector within this range.
ScreenChange of projection screen
according to aspect ratio
Screen with 4 : 3 aspect ratio
90° 90°
Install the projector so the lower
edge of the projection screen is
at the same height as the...

Installing the Projector (Cont.)
Relationship between Projection Distances and Projection Screen Sizes
For 4 : 3 aspect ratio screens
ProjectionProjection screen size (diagonal length)
distanceMinimum projection screen size (Tele end)Maximum projection screen size (Wide end)
8.2 ft (2.5 m)
42” (approx. 107 cm) 63”(approx. 160 cm)
9.84 ft (3.0 m)
51” (approx. 130 cm)76” (approx. 193 cm)
13.12 ft (4.0 m)
68” (approx. 173 cm) 102”(approx. 259 cm)
16.4 ft (5.0 m)
86” (approx. 219 cm) 128”(approx. 325 cm)...

Installing the Projector (Cont.)
Effective Range and Distance of the Remote Control Unit
The operable distance of the remote control unit is about 10 m (32.8 ft) for direct reception. The remote control can \
be used by
having it reflected on the screen, etc. When you use the remote control by reflecting it at the screen, the total distan\
ce of A  + B
should be about 10 m (32.8 ft) or less. The operable angles of the remote control unit is 50° right to left, and 15\
° up and dow n.
The effective range...