Panasonic Digital Video Camera Recorder AG-DVC200P Operating Instructions

10
3Connect the plug of the battery pack to the
connector  inside  the  battery  case,  and
insert the battery pack into the case.
The  power  must  be  turned  off  without  fail  before  connecting  or
disconnecting the plugs.
AU-BP402
battery pack Label
surface
Preparations
Using the AU-BP402 or AJ-BP490 battery pack made by Panasonic
1Remove the battery holder.
Disconnect these.
2Install the battery case into the unit.
Battery holder
Recharge the battery pack using the battery charger specifically...

11
Preparations
Using a battery pack made by
Anton Bauer
1Attach  the  battery  pack  made  by  Anton
Bauer.
2Insert  the  battery  pack  and  slide  it  in  the
direction of the arrow.
Power output connector for lighting
Battery pack made by Anton Bauer
Before  use,  charge  the  battery  pack  using  the  exclusive  battery
charger made by Anton Bauer.
For  the  charging  time  and  other  details,  refer  to  the  operating
instructions of the battery charger used.
Lighting control switch
A  battery...

12
Attaching the lens
1Raise  the  lens  lever,  and  remove  the
mount cap.
4Push  the  cable  into  the  cable  clamp,  and
connect it to the LENS jack.
Mark
3Pull  down  the  lens  lever  to  secure  the
lens.
LENS jack
≥For  details  on  how  to  handle  the  lens,  refer  to  the  operating
instructions of the lens.
≥While  the  lens  is  removed,  attach  the  mount  cap  to  protect  the
unit.
Preparations
Using an AC power supply
(with the AJ-B75 AC adapter)
1Connect  the  unit’s  external  DC...

13
Preparations
Tripod attachment
Mounting the unit on a tripod
1Mount the tripod attachment on the tripod.
Use the tripod attachment to mount the unit on a tripod.
For details on the attachment and adjustments of the viewfinder and
microphone, refer to the operating instructions of the viewfinder.
Take  account  of  the  center  of  gravity  of  the  unit  and  that  of  the
tripod  attachment  when  selecting  the  attachment  hole.    Check  that
the diameter of the hole selected matches the diameter...

14
Preparations
Setting the camera ID
The  camera  ID  is  set  on  the    screen.    Up  to  12
alphanumerics, symbols and spaces can be used.
The camera ID does not appear while the setting menu is displayed
even when color bar signals are output.
The camera ID input above will be recorded at the same time as the
color bar signals.
1Proceed  with  the  sub-menu  operation
(page  30),  and  open  the  
screen.
4Keep  turning  the  JOG  dial  button  until  the
character to be set appears.
6Turn  the...

15
Lens adjustments and checks
The  flange  back  (distance  from  the  lens  mounting  surface  to  the
image  formation  surface)  is  adjusted  when  a  subject  cannot  be
brought  into  focus  precisely  using  either  the  telephoto  or  the  wide
angle positions when performing zoom operations.
Once the flange back has been adjusted, it need not be re-adjusted
unless  the  lens  is  replaced.    For  details  on  the  adjustment  method
and  lens  positions,  refer  to  the  operating...

EX    TAPE NEAR END FLUO.
48K 
CH2
iREC  TCG 12:34:56:00
0
dB
1100  LOW LIGHT
DJAN-01-01 23:59:00
=========
¢¢¢ min
13.4V Z78
ATW
F56CH1
AWB+02
32K
.
.
SPOT    QUICK FOCUS¢1¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢
¢2¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢
FL1
/
2 1<
4
5
6 7
8
9
:
;GHFD
E C B
A
@
? > = I
16
EX    TAPE NEAR END FLUO.
48K 
CH2
TCG 12:34:56.00 NDF
SHUT  :OFF     SKIN  :OFF
!¢¢¢¢¢¢¢¢¢¢¢¢
DJAN-01-01 23:59:00
=========
 ¢¢¢  min
13.4V WHITE :A 3.6K
KNEE  :MANUAL  A.IRIS:BACKSCENE   F1:FLUO.
GAIN  :0dB     GAMMA :NORMAL
FILTER:1       COLOR...

17
Displayed when the AWB has been attained for channel A.
Displayed  when  the  AWB  has  been  attained  for  channel  A,  and  the  color
temperature is lower than the display range.
Displayed  when  the  AWB  has  been  attained  for  channel  A,  and  the  color
temperature is higher than the display range.
Displayed when the AWB has been attained for channel B.
Displayed  when  the  AWB  has  been  attained  for  channel  B,  and  the  color
temperature is lower than the display range.
Displayed...

18
Viewfinder displays
;Audio level meter
displayIndicates the audio levels of CH1 and CH2 (see page 27).
Display item What is displayed Status causing the display to appear
9LOW LIGHT warning
displayLOW LIGHTDisplayed when the brightness has been reduced.
@AWB color
temperature display¢.¢KIndicates the color temperature.
8Shutter speed1/¢¢.¢
1/100 - 1/2000
SUPER VDisplayed when the shutter speed has been set to SYNCHRO SCAN.
Displayed when a fixed shutter speed has been set.
Displayed when SUPER V (high...

19
Viewfinder displays
Display item What is displayed Status causing the display to appear
JCause of !LED
lighting display
(this item appears
only during a MODE
check)SUPER-V
EXT ON
FIL No1
FIL wo No1
FIL NG
SHUT wo 1/100
SHUT ON
WHITE ATW
WHITE PRE
GAIN wo 0dBDisplayed when SUPER-V is set to ON.
Displayed when EXTENDER is set to ON.
Displayed when FILTER is set to 1.
Displayed when FILTER is set to a number other than 1.
Displayed when FILTER is set to NG.
Displayed when SHUTTER is set to a speed other...