Panasonic Digital Imaging Systems For Copy And Network Scan Functions Dp 8032 Operating Instructions

11
Getting To  KnowYour Machine
Installation
■ The maximum power consumption is 1.45 kW.
A properly wired (grounded), dedicated, 15A, 120V AC outlet is required. Do not use an extension cord.
The power cord on this machine must be used to disconnect the main power.
Please ensure that the machine is installed near a wall outlet and is ea\
sily accessible.
Caution Note:  Unplug the power cord from the wall outlet before removing covers.
Supplies
■Store the Toner Bottle and paper in cool areas with low...

12
Getting To  Know Your  Machine
Ventilation
■The machine should be installed in a well-ventilated area to minimize the ozone density in the air.
WARNING For USA
Handling
■Do not turn the Power Switch Off or open the Front Cover during copying/printing.
■ Sleep/Shutdown Mode Notice
●  The following functions will not work if the Sleep/Shutdown Mode setting is set to the Shutdownmode.
When using any of the following functions, we recommend that you leave t\
he Sleep/Shutdown
Mode in the initial factory...

13
Getting To  KnowYour Machine
■ Auto Reset Time
As the initial setting for Auto Reset Time is 1 minute, selected default operation mode backs to default operation
mode after 1 minute. If you wish to change Auto Reset Time, consult your Key operator. (See page 77)
■ Inner Tray Notice
Under normal operation, it is not necessary to remove this Inner Tray. If this tray is
removed, lift up the Paper Holder while reinstalling the tray to prevent\
 damaging it.
Inner TrayPaper Holder
■ Hard Disk Deletion...

14
Getting To  Know Your  Machine
Security Suggestions for Key Operators
To keep your machine’s highly-sensitive document data
secure, the designated Key Operators are instructed to
perform the recommended security measures described
below for the initial machine installation, network
connection, network configuration, setup of security
functions, and replacement and disposal of the machine.
1. Key Operators are required to verify the identity of themanufacturer’s service technician, or of an...

15
memo 

16
Getting To  Know Your  Machine
Operation Chart
Reduction/ Enlargement
only
(See page 32)If set to other
function mode
*30 originals
 (Legal/Ledger)
Select desired settings
(See page 17)
Number of Copies
(Max. 999)
Face Up
Original Guides
Adjust to the original’s width
From
ADF
From
Platen
Load Paper
(See page 18)
Turn the Power
Switch on the Left
side of the machine
to the ON position.Face Down
●
If the original is not
positioned properly, a
portion of the original may
not be copied.
● For originals...

17
Getting To  KnowYour Machine
Adjust the Manual Exposure
                     or
Select type of Original(s)
Mainly Text Text and Photo
combined Mainly Photo
Receiving Tray  (Lower) Receiving Tray  (Upper)
Tray/1-Bin Finisher (External)  INNER 2 and OUTER are only available when the optional Inner Tray or Exit Tray/1-Bin Finisher is installed.
Copy Jobs
(See pages 30-39) (See pages 40-47) (See pages 48, and 49)
(See pages 50-57) (See pages 58-63) (See pages 64, and 65)
■
■ ■
■
■  Problem Solving...

18
Getting To  Know Your  Machine
●
● ●
●
●  Adding Paper (Paper Tray)
●
● ●
●
●  Adding Paper (Sheet Bypass)
Copying on Special Paper, etc. Paper Weight: 16-24 lb
Sheet Bypass
Until it Stops
12
Adding Paper
12
Adding Paper
Operation Chart
■
■ ■
■
■  Problem Solving
●
● ●
●
●   Replacing Toner  Bottle/Replacing Toner Waste  Container
Replace Toner  Bottle
Replace Toner Waste
Container
Toner Waste Container
Shake the new Toner 
Bottle well to loosen the contents. Seal
Toner Bottle
(New)
12
67 

19
Getting To  KnowYour Machine
Load Paper
(Do not exceed limit mark)
Approximately up to 50
Letter size sheets/20 lb
Paper Weight: 15-35 lb
To add paper to the Sheet Bypass, remove the paper left on the tray, and
align it with the added paper and load them together onto the tray.
Paper Capacity: 550 Sheets (20 lb)
NOTE:
If the paper size is not detected,
remove paper and press Reset Key.
Then, load the paper again.
Max Level Indicator
Face DownSide Guides
NOTE:
When changing the paper size, refer
to...

20
Getting To  Know Your  Machine
Operation Chart
■
■ ■
■
■  Problem Solving (Continued)
●
● ●
●
●  Replacing the Staple Cartridge (When optional 1-Bin Finisher is instal\
led.)
Check the
operation
or
Add Staples
12
678
●
● ●
●
●  User Error Codes (U Code)
U1
U4 U6
U7
U13
U14
U15
U16
U25 
U12
U11
U20/U21/U22
U90
U8
Code Check Points
U1 Front Cover is open.
U4 1-Bin Finisher is separated from the machine.
U6 Right Cover is open.
U7 Feed Cover 1/2/3 is open.
U8 Transport Cover is open.
U11 Paper remains...