Panasonic Digital Imaging Systems For Copy And Function Parameters Dp 8060 Operating Instructions

31
Making Copies
23
4
5
Reduction/
Enlargement only
(Letter-R or
Ledger size)
 Default copy size is reduced, copy size can beselected as 100 % or reduced.
 Refer to 11 Booklet Default Mag. of the  Copier
Settings . (See page 73)
Number
of Copies
When the Fold Position is not matched with center
position of the copies, set the binding margin. Refer to
15-17 Fold Position of the  General Settings (For Key
Operator) . (See page 77)
The stapled copies are delivered to the
saddle tray of the 1-bin saddle...

32
Making Copies
2-Sided/Original  Copy
Use this function when copying mixed size originals
(Ledger or Letter and Legal) using the ADF, original
size can be detected automatically then can be
copied to the same size or one specified size.
The followings are examples of Original and Copy
images when Multi-Size Feeding and 1 
 2 Copy
mode are combined.
Originals CopiesFull Size ReductionEnlargement
Legal Legal Letter-R/In
voice Ledger
Letter-R Letter-R Letter-R/In voice Ledger
Ledger Ledger...

33
Making Copies
453
Bind position
or
Number
of Copies
FaceBack
Copy Images (1  2 copy mode)
Ex.   Bind Position is SHORT EDGE
*1 Ledger size will bereduced to Letter size.
*2 Legal size will be reduced to Letter size.
Ledger
(Landscape
layout)
Letter
(Portrait)
Letter*1(Landscape
layout)
Legal(Portrait
 layout)
Letter(Portrait
layout)Letter*2(Portrait
layout)
Letter(Portrait
layout)Blank
Letter
(Portrait)Blank 

34
Making Copies
2-Sided/Original  Copy
Special originals (like thin paper, etc.) can be fed
from the ADF Tray and copied continuously using
the Job Build and SADF Mode.
If the Job Build and SADF buttons are not shown
on the Touch Panel display, the Job Build and
SADF Modes must be enabled in the copier
function settings. Please consult with the Key
Operator. (See page 80)1
5
Place one Original
at a time or up to 85
sheets (20 lb)/Letter
70 sheets (Ledger/
Legal/Invoice)
2
Reduction/
Enlargement
only...

35
Making Copies
5
6
3
Number
of Copies
4
When all the pages are read by the ADF,
Another Original? YES or NO message
appears.
Select the NO button.
5
6
3
Select Sorting/Finishing settings
oror etc.Number of
Copies
(
Ex.  5)
4
When all the pages are read by the ADF, after
approximate 5 seconds Another Original? YES
or NO message appears.
Select the NO button. 

36
Making Copies
Sort/Finish
1
1
1
1
1
1
3
1
2
1
1
1
3
1
2
Multiple copy sets are sorted
automatically. When loading both Letter and
Letter-R sized paper, multiple
copies of individual pages are
stacked in alternate direction
(rotation of 90 degrees).
(Letter size only)
When optional Finisher is installed.
Offset stacking using electronic
sorting
● DA-FS330 (Letter/Lower Bin only)
● FS355A/FS600/FS605
(Letter, Letter-R, Legal, Ledger) When optional Finisher is installed.
Offset stacking using...

37
Making Copies
or
orSort modeor
or
When the optional Finisher is installed, this screen will change as follows:
For DA-FS330
or
When overflow           indicator appears on the display,
remove excess copies from the bin. ●Overflow
Number
of Copies
oror
For DA-FS600/FS605
ororor
oF
For DA-FS355A
123
Staple Position
Ex.  Top left corner
Original
ADF 

38
Making Copies
Zoom/Effects
Copies with variable zoom ratios from 25 %
to 400 % in 1 % increments.
25%400%
1
or
2
The copy Zoom Ratio adjusts automatically to the
selected paper size.
Fit to paper length or width
Fit to paper length and width
12
Opening the ADF
wider than 45
degrees.
∗1
NOTE●If the margin around the original is 5 mm wide or less, the original may\
 not be correctly
detected, and the copy image may be unclear.
Zoom/Effects
■
■ ■
■
■  Zoom
■
■ ■
■
■  Auto Zoom
∗1:For Auto Zoom
An...

39
Making Copies
34
or
Same vertical and
horizontal ratio
25% - 400%
or
or Keypad Different vertical and
horizontal ratio
25% - 400%
or
or Keypad
orNumber
of Copies
∗2
∗2
35
Number
of CopiesEnlarged or reduced
according to the vertical/
horizontal size of the
paper.
Paper Size
(Paper Tray)
Enlarged or reduced
according to both
vertical/horizontal size of
the paper.
4
ATTENTION●
When changing the paper size after setting the zoom ratio, use the PAPER TRAY button.
If paper size is changed with Copy size...

40
Making Copies
Zoom/Effects
Unnecessary edge can be erased by setting a blank
edge.
NOTE:
When ZOOM is selected, the erasing width
varies depending on the zoom ratio.
12
or
When copying original such as the center of folding
position may be shaded. This shade can be easily
eliminated.NOTE:
● When ZOOM is selected, the erasing
width varies depending the zoom ratio.12
NOTE●If the margin around the original is 5 mm wide or less, the original may not be correctly
detected, and the copy image may be...