Panasonic Digital Disk Recorder Wj Hd220 Operating Instructions

							61
•Even if preset to 30 or 15 FPS, the actual recording rate
may drop to 7.5 FPS at worst while busy multi task such
as playback, remote-access playback, remote-access
live image, FTP access, multi-split display, or video
motion detection are carried out simultaneously.
The status display will indicate  *→ PLAY while playing
back the images recorded with a rate different from the
preset.
•The suffix xxx following SP- is specified in REC
MODE TABLE in the ADDENDUM attached to the man-
ual.
1. Select a recording mode. Audio data will be recorded
when a mode with hyphen A is selected.
Available recording modes:SF, FQ, NQ, EX, SP, SF-
A, FQ-A, NQ-A, EX-A, and SP-A
2. When SP or SP-A is selected, specify a recording rate
(REC RATE).
Available recording rates:From 0.1 to 30 FPS
3. When SP or SP-A is selected, specify a recording quali-
ty (REC QUALITY).
Available recording qualities:SUPER FINE, FINE,
NORMAL, EXTENDED
8Alarm Recording Mode Setup (ALM REC MODE)
Recording of alarm events arising within the time zone
specified by the program will start with the preset parame-
ters.
Refer to PROG NO. SETUP described above for operating
procedures and available parameters, since they are very
similar.
8Pre-alarm Recording (PRE ALM REC)
Available times (seconds):0S, 1S, 2S, 3S, 4S, and 5S
8Post-alarm Recording (POST ALM REC)
Available times (seconds):5, 10, 20, 30
Available times (minutes):1, 1.5, 2, 3, 6
Continue:Recording continues until the [RESET] but-
ton is pressed, or the RESET IN signal is supplied to
the rear panel.
Manual: Recording continues while the alarm input is
active, or at least for 10 seconds if the input turns
inactive earlier.
8Dynamic Recording (DYNAMIC REC)
ALM-MULTI:Alarm activated channels are recorded
with priority over others.
OFF:All channels are recorded with the same priority.
Trigger Action Setup (TRIGGER
ACTION SETUP)
This menu specifies the actions the recorder will take for
each event when an alarm arises. The program number
and event number in the second line of the menu will disap-
pear when the screen is changed from the REC SETUP
menu.
8Mode (MODE)
OFF:Disables alarm recording, logging, or warning.
REC&ALARM:Enables all alarm recording, logging
and warning.
REC: Enables alarm recording, but disables warning.
Notes:
•Moving the combination cameras to the preset position
can be set only from the REC SETUP menu, not from
the Program 1-4 menu. 
•To open the menu for setting positions, click the [TRIG-
GER ACTION SETUP] button in the REC SETUP menu.
Click the [SET] button when items have been set properly. 
						

							62
Camera Recording Setup (REC
CAMERA SETUP)
Click CAMERA REC SETUP in the system setup window to
open the menu.
This menu is provided for the purpose of saving disk
space. Each camera channel can be recorded only when
an alarm operates, while it will not be recorded in non-alarm
status.
ALARM-ONLY:Records the camera channel only
when the alarm operates.
REC:Records the camera channel regardless of alarm
or non-alarm status.
Manual Recording Setup 
(REC SETUP)
Manual recording will take effect when OFF (not INT or EXT)
is selected in the Timer Mode Selection TIME REC window.
The parameters for alarm recording will be applied except
for the scheduled time zone if INT is selected.Click the [REC SETUP] button on the setup control panel to
open the window.
Refer to Recording Mode Setup PROG1-4 SETUP, NO. 1-
4 for operating procedures and available parameters.
Trigger Action Setup (TRIGGER
ACTION SETUP)
This menu appears when the [TRIGGER ACTION SETUP]
button in the REC SETUP menu is clicked.
8Mode (MODE)
OFF:Disables alarm recording logging, and warning.
REC&ALARM:Enables alarm recording logging, and
warning.
REC:Enables alarm recording, but disables warning.
8Camera Preset Position (PRESET)
When combination cameras are connected to VIDEO IN
1-4 on the rear panel and positions are specified
beforehand, you can assign a position to cameras 1-4. 
1-64:Moves the camera to the specified preset posi-
tion.
HOME:Moves the camera to the home position.
– –:Does not move the camera.
Note:Preset move will not function for cameras 5-8 or
for cameras 1-4 if they are cameras other than com-
bination cameras.
Click the [SET] button when the items have been set prop-
erly. 
						

							63
TYPE2 12H:Time and date are displayed in two lines in
the AM-PM system.
OFF:Time & date display is disabled.
8Time and Date Position (TIME&DATE POSITION)
Right-Lower:Displays time & date in the lower right
corner.
Right-Upper:Displays time & date in the upper right
corner.
Left-Lower:Displays time & date in the lower left cor-
ner.
Left-Upper:Displays time & date in the upper left cor-
ner.
8Time & Date Embedded (TIME&DATE
EMBEDDED)
ON:The display will be embedded and recorded with
the image data.
OFF:The display will not be recorded.
8Status Display (STATUS DISPLAY)
ON:Status display is enabled.
OFF:Status display is disabled.
8Status Display Position (STATUS POSITION)
Right-Lower:Displays status in the lower right corner.
Right-Upper:Displays status in the upper right corner.
Left-Lower:Displays status in the lower left corner.
Left-Upper:Displays status in the upper left corner.
8HDD Full (HDD FULL)
1% - 99%:The FULL indicator blinks when the remain-
ing capacity reaches the selected value. This will
take effect when DISK END MODE is set to STOP in
the RECORD SETUP.
8Remote LED (REMOTE LED)
ON:REMOTE LED turns on when the network controls
the recorder. 
OFF:REMOTE LED is deactivated.
8HDD Check (HDD CHECK)
ON 0:00 - 23:00:The recorder checks the HDD at the
specified time every day.
OFF: Check is deactivated.
Click the [SET] button when all items have been set proper-
ly.
Click the [CAMERA TITLE SETUP] button to open the CAM-
ERA TITLE window.
Externally Specified Recording
Mode (EXT REC SETUP)
This window specifies the recording mode and parameters
that will be changed when the switch externally connected
to the EXT REC terminal is turned on.
Refer to Recording Mode Setup PROG1-4 SETUP, NO. 1-
4, for operating procedures and available parameters.
Display Setup (DISPLAY SETUP)
Time and date display and other displays of status informa-
tion are specified in this window.
8Clock Setup (CLOCK SETUP)
Select a month, and type a day, year, hour, and minute.
8Time and Date Display (TIME&DATE DISPLAY)
TYPE1 24H:Time and date are displayed in one line in
the 24-hour system.
TYPE1 12H: Time and date are displayed in one line in
the AM-PM system.
TYPE2 24H:Time and date are displayed in two lines in
the 24-hour system. 
						

							64
Camera Title (CAMERA TITLE)
8On/Off (ON/OFF)
ON:Displays the camera title.
OFF:Hides the camera title.
8Title (TITLE)
Usable characters:Are shown in the window.
Number of digits:5 digits maximum.
8Title Position (POSITION)
Right-Lower:Displays the title in the lower right corner.
Right-Upper:Displays the title in the upper right cor-
ner.
Left-Lower:Displays the title in the lower left corner.
Left- Upper:Displays the title in the upper left corner.
Click the [SET] button when all items have been set proper-
ly.
System Setup (SYSTEM SETUP)
8Password Lock (PASSWORD LOCK)
Buttons on the front panel of the WJ-HD220 will be 
password-protected or freed.
ON:Enables password-protection.
OFF:Disables password-protection.
8Password All (PASSWORD ALL)
Enter a five-digit password comprising 1 through 8 to
protect normal operations and setup operations from
unauthorized access.
Available numerals:From 11111 to 88888
8Password Operation (PASSWORD OPERATION)
Enter a five-digit password to protect normal operations
from unauthorized access.
Available numerals:From 11111 to 88888
8Keylock Buzzer (KEYLOCK BUZZER)
The buzzer will beep or not when a locked button is
pressed.
ON:Enables the buzzer beep.
OFF:Disables the buzzer beep.
8Skip Alarm Recall (SKIP ALARM RECALL)
Specify the number of pages to be skipped in the alarm
log. The alarm log page will jump the specified pages
when the JogDial is rotated.
Available skip pages:1, 5, 10, 20, 50
8Simultaneous Recording and Playback 
(SIMULTANEOUS REC&PLAY)
There may be cases where recording is essential while
playback is in progress.
ON:Allows both recording and playback at a time.
OFF:Allows exclusively recording or playback. 
						

							65
Note: The recording rate may be sacrificed in the fol-
lowing cases.
•Recording and playback/FTP access are carried
out simultaneously.
•A multi-split screen is displayed.
•VMD (video motion detection) is enabled.
•A PC accesses the live images via the network.
8Alteration Detection (ALTER DETECT)
You can enable or disable the addition of alteration-
detection signals in the JPEG data supplied to the net-
work. The default is OFF.
ON:Detects alterations.
OFF:Does not detect.
Note:When set to ON, the data transmission rate on
the network will slow down.
8Disk End Mode (DISK END MODE)
STOP:Stops recording until a mode other than [STOP]
is selected.
CONTINUE: Old data is automatically overwritten from
the disk start.
8Disk End Buzzer (DISK END BUZZER)
ON:Enables the buzzer beep at the disk end (remain-
ing space = 0 %).
OFF: Disables the buzzer beep.
8Play Priority (PLAY PRIORITY)
This setting places priority on a specific access point
for playing back the image data when access collisions
take place.
LOCAL:Places priority on front panel operations.
NET PLAY:Places priority on network access.
FTP GET:Places priority on access to the FTP.
NONE:The latest operation has priority over others.
8Time Adjusting (TIME ADJUSTING)
The internal timer built into the WJ-HD220 is calibrated
once a day via the Time Adjust In and Out terminals on
the rear panel.
SLAVE:Accepts the calibration signal from the master.
MASTER:Supplies the calibration signal to the slave
units at the specified hour every day. 
						

							66
Video Motion Detector Setup
(VMD SETUP)
8Sensitivity (SENSITIVE)
LOW:Low sensitivity
MID:Medium sensitivity
HIGH: High sensitivity
OFF:Motion detection is disabled.
Click the [SET] button when all items have been set proper-
ly.
Click the [SETUP] button to open the area setup window.
VMD Area Setup (VMD AREA
SETUP)
Drag a maximum of four areas with the mouse to specify
the detection areas.
Click the [SET] button when all items have been set proper-
ly.
Alarm Setup (ALARM SETUP)
8Alarm Buzzer (ALARM BUZZER)
ON:Buzzer beeps while alarm is active.
OFF:Buzzer does not beep.
8Video Loss Detection (VIDEO LOSS DETECT)
OFF:Deactivates the video loss detection.
ON:Activates the detection.
8Multiscreen Monitor Mode (MONITOR MODE
(MULTI))
SPOT: Switches to the picture of the channel where
alarm has operated.
OFF:Retains the previous display mode.
8Spot Monitor Mode (MONITOR MODE (SPOT))
SPOT: Switches to the picture of the channel where
alarm has operated.
OFF:Retains the previous display mode.
Click the [SET] button when all items have been set proper-
ly. 
						

							67
8Parity Check (PARITY CHECK)
NONE:No parity check
EVEN: Even parity
ODD:Odd parity
8Stop Bit (STOP BIT)
1 bit: 1 bit
2 bit:2 bits
8Wait Time (WAIT TIME)
OFF:Retransmission is disabled.
100 MSEC: 100 m seconds
200 MSEC:200 m seconds
1 SEC: 1 second
8Control Unit Addresses 
(CONTROL UNIT ADDRESS) (only for PS
•DATA)
Assignable address:From 1 to 99, must be unique in
the chain.
8System Unit Address (SYSTEM UNIT ADDRESS) 
(only for PS
•DATA)
Assignable addresses:From 1 to 99, must be unique
in the chain.
8Alarm Data (ALARM DATA)
OFF: Select this when no system controller is connect-
ed.
0 SEC: Does not pause.
1 SEC: Pauses for 1 second.
5 SEC:Pauses for 5 seconds.
Click the [SET] button when all items have been set proper-
ly.
Click the [CAMERA SYSTEM SETUP] button. The CAMERA
SYSTEM SETUP window opens.
Communication Setup
(COMMUNICATION SETUP)
Click the [SERIAL PORT SETUP] or [NETWORK SETUP]
button. The respective window opens.
Serial Port Setup 
(SERIAL PORT SETUP)
8Protocol Selection (PROTOCOL SELECT)
PS•DATA: Select when the communication chain uses
the PS
•DATA protocol.
When selected, the DATA terminal on the rear panel
can be used.
RS-232C: Select when other than PS
•DATA is used. 
When selected, the RS-232C terminal on the rear
panel can be used.
8Baud Rate (BAUD RATE) 
4800: 4 800 bps
9600: 9 600 bps
19200: 19 200 bps
8Data Bit (DATA BIT) 
7: 7 bits 
8: 8 bits 
						

							68
Camera System Setup
(CAMERA SYSTEM SETUP)
(only for PS
•DATA)
8Camera Number (CAMERA No.)
The camera number assigned to the port is used when
a system controller accesses the camera.
Assignable numbers:From 1 to 128, must be unique
in the chain.
8Compensation level (COMPENSATION)
Video signal loss can be compensated for the length of
the coaxial cable. S stand for short-distance, M for
medium, and L for long.
S: ≤500 m
M:500 m – 900 m
L:900 m – 1 200 m
8Data Communication (DATA)
ON:Enables data communications by use of PSD com-
mands multiplexed on the coaxial cable.
OFF:Disables coaxial-multiplexed communications.
Click the [SET] button when all items have been set proper-
ly.
Network Setup (NETWORK
SETUP)
8Line Speed (LINE SPEED)
AUTO: The speed is automatically selected.
100Mbps (FULL DUPLEX):100 mega byte, full duplex
100Mbps (HALF DUPLEX): 100 mega byte, half
duplex
10Mbps (FULL DUPLEX): 10 mega byte, full duplex
10Mbps (HALF DUPLEX): 10 mega byte, half duplex
8HTTP Server Port (HTTP SERVER PORT)
Enter from the keyboard. The default setting is 80.
8DHCP On/Off (DHCP ON/OFF)
Select ON or OFF for DHCP (Dynamic Host
Configuration Protocol). 
IP Address (IP ADDRESS) 
The IP address is displayed. Enter from the keyboard.
Netmask (NETMASK)
The netmask is displayed. Enter from the keyboard.
Default Gateway (DEFAULT GATEWAY) 
The default gateway is displayed. Enter from the key-
board. 
						

							69
8Domain Name Service (DOMAIN NAME SERVICE)
OFF:Disables DNS, only IP address usable.
MANUAL:Enables DNS.
AUTO:Enables DNS.
Domain Name (DOMAIN NAME)
Enter from the keyboard.
DNS Server Address (DNS SERVICE ADDRESS)
Enter from the keyboard.
8Dynamic DNS (DYNAMIC DNS)
OFF:Does not use DDNS.
ON:Uses DDNS.
DDNS Host Name (DDNS HOST NAME)
Enter from the keyboard. 
DDNS User Name (DDNS USER NAME)
Enter from the keyboard. 
DDNS Password (DDNS PASSWORD)
Enter from the keyboard. 
DDNS Access Interval (DDNS ACCESS INTERVAL)
Enter from the keyboard.
8Simple Network Management Protocol
Note: (double quotation) cannot be used for SNMP.SNMP Community (SNMP COMMUNITY)
Enter from the keyboard.
SNMP Contact (SNMP CONTACT)
Enter from the keyboard. 
SNMP System Name (SNMP SYSTEM NAME)
Enter from the keyboard. 
SNMP System Location (SNMP SYSTEM LOCATION)
Enter from the keyboard.
Click the [SET] button when all items have been set proper-
ly.
The WJ-HD220 will restart, and you will be requested to
enter the URL as described earlier in Main Page and
Control Panel. 
						

							70
Switcher Setup (SWITCHER
SETUP)
This window specifies sequence setups only for the WJ-
HD220. The browsers sequence is set up in LIVE
SEQUENCE SETUP on page 77.
8Common Setup (COMMON SETUP)
Multiscreen monitor Start Display (START DISPLAY
(MULTI))
Spot monitor Start Display (START DISPLAY
(SPOT))
The image in the selected form will be displayed on the
multiscreen monitor and spot monitor when the unit is
turned on.
Single image:CH 1 – CH 8*
Quad image:QUAD-4A (including 1-4), QUAD-4B
(including 5-8)
Multi image:9-SCREEN (including 1-8)
Sequence:SPOT SEQUENCE*, MULTI SEQUENCE
Note:The spot monitor can display only a single image
or spot sequence while the multiscreen monitor can
display any of the forms listed above.
Multiscreen Selection Mode (MULTI SELECT MODE)
When the [MULTISCREEN SELECT] button on the front
panel is pressed, the monitor display will be switched
as follows depending on the setup.
QUAD ONLY:QUAD-4A →QUAD-4B →QUAD-4A
ALL:QUAD-4A →QUAD-4B →9-SCREEN →
QUAD-4A 
8Multiscreen Sequence Setup 
(MULTI SEQUENCE SETUP) 
Sequence Timing (SEQUENCE TIMING) 
INT:The time preset on the internal timer allows the
sequence to move a step forward.
EXT:The SEQ IN signal on the rear panel allows
the sequence to move a step forward.
Auto Skip (AUTO SKIP)
ON:The sequence skips any step where no video
is input.
OFF:The sequence does not skip the step.
Click the button to open the Multi Sequence Setup window.
8Spot-screen Sequence Setup
(SPOT SEQUENCE SETUP)
Sequence Timing (SEQUENCE TIMING)
INT: The time preset on the internal timer allows the
sequence to move a step forward.
EXT:SEQ IN signal to the rear panel allows the
sequence to step forward.
Auto Skip (AUTO SKIP)
ON:The sequence skips any step where no video
is input.
OFF:The sequence does not skip the step.
Click the button to open the Spot Sequence Setup window.
8Camera View Setup (CAMERA VIEW SETUP)
Secret View (SECRET VIEW)
ON: The spot monitor screen will be blacked out
when the multiscreen monitor displays images
in the single live mode.
OFF:The spot monitor continues to display images
regardless of the multiscreen monitor status.
Click the button to open the Camera View Setup window.
Note:The secret view function will be useful to watch
shoplifters without being recognized in a store
where, for example, cameras and spot monitors are
installed on the sales floors and a multiscreen moni-
tor is installed in a control room. The spot monitor
will black out its screen when the multi-screen moni-
tor is switched to the single live mode to focus on
the potential shoplifter.