Panasonic Digital Disk Recorder Wj Hd220 Operating Instructions

							51
Orange:The channel image is not displayed.
Yellow:The channel image is displayed.
The multiscreen monitor displays the recording images
while the corresponding input indicators on the front
panel light in yellow.
2. Hold down the [REC STOP] button for 2 seconds to
stop recording. The REC indicator turns off.
Alarm Recording
Alarm recording starts when an externally connected sen-
sor is turned on, the built-in VMD (Video Motion Detector) or
the built-in video loss detection is activated.
Alarm recording will proceed, then stop when the post-
recording time has elapsed.
If more than one alarm arise, for instance ALM1 and ALM2,
the images of the alarmed inputs are recorded on the disk
as shown in the figure.
Note:HDD indicator will continue to blink for a period
equivalent to the specified pre-alarm time at the end of
alarm recording.
Power-on Recording
For power-on recording, select EXT for TIMER in the WJ-
HD220 MAIN menu. The recorder starts recording when AC
power is supplied.
This enables the disk recorder to start recording everyday
at a specific time by the use of a timer switcher that con-
trols the AC mains supplied to the recorder. The power
switch on the rear of the recorder must be turned on in this
case.
Manual Recording
Manual recording is available when OFF is set for TIMER in
the WJ-HD220 MAIN menu. The menu setup can exempt
specific inputs from manual recording for the purpose of
preserving disk capacity. The recording mode (SF-24, for
example), picture quality (fine) and recording rate (30 fps)
are set in the menu setup by specifying two of the three
parameters. SF-24H is an example having a picture quality
of especially fine grade and 48 hours of recording capacity.
1. Press the [REC] button on the front panel to start
recording. The indicator in the [REC] button lights up
while the [CAM SEL] button of the channel indicates
and the channel image is displayed on the multiscreen
monitor.Sensor
Built-in
VMD
OPERATEALARM
SUSPEND
RESETHDDFULLERROROSDMULTISCREEN
SELECTZOOM
TIMER
REMOTE
LOCKSEQUENCEALARM
SERCHSTOP
PLAY MODE SELECT
SETUP
/ESCPLAYTIME&DATE
SEARCHREC STOPSPOT
MULTICAMERA SELECT
ALARM
RECALLRECPUSH—    PAUSESET
Digital Disk Recorder WJ-HD220
1
52
63
74
8DST
C
4C
8C
1C
1C
1C
1C
1C
2C
1C
2C
2C
2C
2C
2C
3C
4C
8
Alarm 1
Alarm 1 DurationAlarm 2
Alarm 2 Duration
C
1C
2C
3C
4C
8C
1C
2C
3C
4C
8C
1C
2C
3C
4C
8C
1C
2
C1C2C3C4C5C6C7C8C1
StartStop
TIME&DATE
SEARCH
REC STOP
REC
Timer 
Switch
AC Mains
OPERATEALARM
SUSPEND
RESETHDDFULLERROROSDMULTISCREEN
SELECTZOOM
TIMERDSTREMOTE
LOCKSEQUENCEALARM
SERCHSTOP
PLAY MODE SELECT
SETUP
/ESCPLAYTIME&DATE
SEARCHREC STOPSPOT
MULTICAMERA SELECT
ALARM
RECALLRECPUSH—    PAUSESET
Digital Disk Recorder WJ-HD220
1
52
63
74
8 
						

							52
3. Rotate the JogDial clockwise to move forward in the
recorded data or counter-clockwise to move backward. 
The more turns you rotate the JogDial, the faster the
skip speed will be.
4. Press the [STOP] button to stop playback.
Step Playback
A minute search is made for a desired picture field by field.
1. Press the [PLAY] button to start playback.
2. Press the [STEP] button to start step playback. The LED
in the button blinks. 
3. Rotate the JogDial clockwise to advance to the next
later field or counter-clockwise to rewind to the next
older.
4. Press the [STOP] button to stop playback.
Alarm Search Playback
Alarm records on the disk are searched while viewing the
beginning image of the record.
1. Press the [PLAY] button to start playback.
2. Press the [ALARM SEARCH] button to start alarm
search playback. The LED in the button lights up. 
3. Rotate the JogDial one click clockwise or counter-
clockwise. The display advances to the beginning of
the next later or next older record. Repeat until the
desired record is displayed.
Playback
In playback modes, the recorded image data are played
back.
Notes:
•Alarm recording will interrupt playback if SIMUL
REC&PLAY is set to OFF, or will allow playback to con-
tinue if set to ON.
•Operation of the [PLAY] button will be ignored if the
disk is empty, for instance, when the recorder is used
for the very first time or right after formatting of the disk.
•The latest recorded image is displayed on the monitor
right after recording finishes. Search for the desired
image by skip playback before starting playback.
Normal Playback
The pictures recorded on the disk are played back sequen-
tially. 
1. Press the [PLAY] button to start playback.
2. Press the JogDial [PUSH–PAUSE] to pause and restart
playback.
3. Press the [STOP] button to stop playback.
Skip Playback
Picture search is available in quick forward and backward
playback. The monitor displays the skip speed as 1/2PLAY,
PLAY, 2PLAY, 1FF, 2FF, 3FF, and so forth. The asterisk indi-
cates that images are played back continuously without
skipping.
1. Press the [PLAY] button to start playback.
2. Press the [REW/FF] button to start skip playback. The
LED in the button lights up. 
ALARM
RECALL
PUSH—    PAUSESET
PLAY MODE SELECT
PLAYRECSTOPSETUP
/ESC
14
23
ALARM
RECALL
PUSH–    PAUSESET
PLAY MODE SELECT
PLAYREC
1,45
2
3
ALARM
SERCH
STOPSETUP
/ESC
STOPSETUP
/ESCPLAY
ALARM
RECALL
PUSH–    PAUSESET13
2
14
23
ALARM
SERCH
STOP
PLAY MODE SELECT
SETUP
/ESCPLAY
ALARM
RECALL
REC
PUSH—    PAUSESET 
						

							53
6. Repeat from step 1 to search for another time and date
or press the [TIME&DATE SEARCH] button to cancel
the function. Pressing the [STOP] button will also end
the searching.
Note: Searching may take the recorder 18 seconds at
worst
Multiscreen Playback
You can view a multiple playback image displayed in 4-split
or 9-split pattern on the monitor at a time.
•Normal Playback
Press the [PLAY] button to start normal playback. The
image data recorded on the disk are sequentially
played back, and the monitor displays images in the
single display mode or multiscreen display mode.
•Multiscreen Playback
Press the [MULTI SCREEN SELECT] button an appro-
priate number of times. The monitor display changes as
follows. The LEDs in the [MULTI SCREEN SELECT] but-
ton and respective input buttons will light up. 
Single Image →Quad A (4A/comprising inputs 1, 2, 3,
and 4) →Quad B (4B/inputs 5, 6, 7, and 8) →Nine-spit
(inputs 1 - 8) →Quad A →Quad B →Nine-split
•Specific Input Playback
Press the respective input button. The images of the
selected input are played back continuously and dis-
played on the monitor.
•Stop Playback
Press the [STOP] button to stop playback.
Note:When the playback proceeds to where recording
is executed on the disk, the recorder will pause
playback and freeze the displayed image on the
monitor. 4. Press the [PLAY] button to play back the searched
record.
5. Press the [STOP] button to stop playback.
Note: Alarm Search Playback and Alarm Log Recall
are similar, but different in operations. Refer to 
Alarm Log Recall & Search on page 49.Time & Date Search Playback
A picture record of a specified time and date is played
back.
1. Press the [TIME&DATE SEARCH] button. The monitor
displays the time & date search window.
2. Press the [D] or [C] button to move the cursor to the
next position.
3. Rotate the JogDial clockwise to increase the parameter
or counter-clockwise to decrease it.
4. Repeat steps 2 and 3 above until the desired parame-
ters are selected. 
5. Press the [PLAY] button to start playback. The monitor
displays the single spot image when an input is select-
ed or the nine-split image when all input is specified.
The recorder stops searching when the playback
reaches the end of the record.
HDD
FULL
ERROR
MULTI SCREEN
SELECT
ZOOM
ALARM
SERCH
STOP
PLAY MODE SELECT
SETUP
/ESCPLAYREC
  JAN31.04  23:00:00 
TO SEARCH PUSH PLAY KEY
5
13
PLAY
TIME&DATE
SEARCH
REC STOP
ALARM
RECALL
REC
PUSH—    PAUSESET
2 
						

							54
Lock/Unlock Buttons
Password Verification
When a locked button is pressed, the key locked warning
appears on the monitor for 2 seconds, then it changes to
the password prompt.
1. Enter your five-digit password using the [CAM SELECT]
buttons (1-8). The buzzer shortly beeps once, and the
entered digit changes from – to  *  on the monitor.
2. The prompt window will display KEY UNLOCKED! for
2 seconds, and the buzzer beeps twice if the correct
password is entered. 
The monitor returns to the previous display. The
recorder allows access to the front panel controls if a
button operation takes place within 5 seconds of pass-
word entry.
3. Retry verification when password error appears on the
monitor.
The recorder will exit from verification if there is no opera-
tion within 30 seconds.
   PASSWORD 
/-----
Enabling Button Lock
1. You need to register passwords in the SYSTEM SETUP
window prior to operating your system.
2. Press the [LOCK] button for 2 seconds.
The buzzer shortly beeps twice, and the LED in the but-
ton lights up. The KEY LOCK DONE! message
appears on the monitor.
Note:Set PASSWORD LOCK to OFF if you do not want
the recorder to revert to button lock mode when no
operation takes place within 5 minutes.
       KEY LOCK DONE!LOCK 
						

							55
WJ-HD220
NETWORK OPERATION 
						

							56
System Requirements
Your personal computer must meet the following minimum requirements.
OS:
One of the following operating systems: 
Windows98 Second Edition
Windows2000
Windows Millennium Edition
WindowsXP Professional or Home Edition
Browser:
One of the following browser software: 
Microsoft Internet Explorer 5.5SP2, 6.0 
Note:The Netscape browsers are not applicable.
Display:
1 024 x 768 pixels or more
Trademarks
Microsoft, Windows, WindowsXP and Internet Explorer are either registered trademarks or trademarks of Microsoft Corporation in the United
States of America and/or other countries.
PREPARATIONS 
						

							57
Connection
System connection examples are shown.

•Connection with a Client PC via Hub

A maximum of four PCs can access the recorder at a time.
WV-CL920
Digital Disk Recorder
Camera
Personal Computer
Ethernet Cross CableOPERATEALARM
SUSPEND
RESETHDDFULLERROROSDMULTISCREEN
SELECTZOOM
TIMER
REMOTE
LOCKSEQUENCEALARM
SERCHSTOP
PLAY MODE SELECT
SETUP
/ESCPLAYTIME&DATE
SEARCHREC STOPSPOT
MULTICAMERA SELECTALARM
RECALLRECPUSH—    PAUSESET
Digital Disk Recorder WJ-HD2201
52
63
74
8DST
Super Dynamic
HubDigital Disk Recorder
Personal Computer Ethernet
Straigth
CableEthernet
Straigth
Cable Camera
OPERATEALARM
SUSPEND
RESETHDDFULLERROROSDMULTISCREEN
SELECTZOOM
TIMER
REMOTE
LOCKSEQUENCEALARM
SERCHSTOP
PLAY MODE SELECTSETUP
/ESCPLAYTIME&DATE
SEARCHREC STOPSPOT
MULTICAMERA SELECTALARM
RECALLRECPUSH—    PAUSESET
Digital Disk Recorder WJ-HD2201
52
63
74
8DST
LAN
HubHub
Digital Disk Recorder
WV-CL920WV-CL920
System 
Administrator
User User
User User Cameras 1-8
OPERATEALARM
SUSPEND
RESETHDDFULLERROROSDMULTISCREEN
SELECTZOOM
TIMER
REMOTE
LOCKSEQUENCEALARM
SERCHSTOP
PLAY MODE SELECT
SETUP
/ESCPLAYTIME&DATE
SEARCHREC STOPSPOT
MULTICAMERA SELECTALARM
RECALLRECPUSH—    PAUSESET
Digital Disk Recorder WJ-HD2201
52
63
74
8DST 
						

							58
Main Page and Control Panel
Start your PC WWW browser. Type http://192.168.0.10/ (or
the IP Address set for WJ-HD220) / in the URL (Uniform
Resource Locators) space.
The browser displays the Main Control Panelof the WJ-
HD220 homepage as shown in the figure.Notes: 
•Specify http//:192.168.0.10/ when a client PC is con-
nected alone.
•Specify http//: (IP address previously set for the WJ-
HD220)/ such as a LAN connection.
•A maximum of four PCs can access the recorder at a
time.
About Picture Quality
Picture quality transferred via the network depends on the recorders status as follows.
Recorder Status Displayed Quality
Timer recording Preset recording quality
Pre-alarm period Preset alarm recording quality
Except pre-alarm period Preset manual recording quality
Playback Recorded quality on the disk 
						

							59
To Access Setup Menus
There are fourteen setup menus to adapt the WJ-HD220 to
your requirements.
1. On the Main Control Panel, click the [SETUP MENU]
button. The setup menu opens.
2. Click the buttons to open the respective windows.

TIMER SETUP:Specifies the schedule and parameters
for timer recordings.
REC SETUP:Specifies the parameters for manual and
alarm recordings.
EXT REC SETUP:Selects optional parameters to be
applied to the recording while the switch connected
externally to the EXT REC terminal turns on.
DISPLAY SETUP:Specifies time-and-date and other
displays of status information.
SYSTEM SETUP:Specifies password-protection, and
simultaneous REC&PLAY.
ALARM SETUP:Specifies alarm-related monitoring
mode, and VMD (video motion detector) mode.
COMMUNICATION SETUP:Specifies parameters for
serial and network communications.
SWITCHER SETUP:Specifies sequence and multi-split
patterns.
WJ-HD220 SETUP
SYSTEM INFORMATION:Displays various system
information.

USER SETUP:Specifies users, passwords, and
access levels.
HOST SETUP:Specifies hosts and access levels.
FTP SETUP:Specifies parameters for transmitting files.
MAIL SETUP: Specifies senders, and receivers.
NETWORK VIDEO SETUP:Specifies application soft-
ware for video translation, and sequence steps.
3. To return to the MAIN CONTROL PANEL, click the
[Main Control Panel] tab or [BACK] button in the win-
dow.
Timer Setup (TIMER SETUP)
Timer Recording (TIMER REC)
OFF:Runs recording when manually operated, not
using any timer. Recording parameters are speci-
fied in the REC SETUP window.
INT:Runs recording with the programmed picture qual-
ity within the time zone scheduled on the internal
timer.
EXT:Runs recording when the externally connected
timer switch turns on and supplies power to the
recorder (Power-on recording). Recording parame-
ters are specified in the REC SETUP window.
Note:Buttons in the setup menus may appear with a
thicker border when using a browser in WindowsXP. 
						

							60
Program Assignment (TIMER REC)
When internal timer (INT) is selected, programs can be
assigned on a weekly and/or daily basis.
Assignable programs:PROG1 – PROG4, OFF
Programming (PROGRAM SETUP)
There are four programs, each containing four events hav-
ing a start and end time, and a recording mode.
1. Select ON or OFF for each event.
ON:Applies the schedule and mode to the program.
OFF:Does not apply.
2. Enter the start and end times.
Assignable START times:From 00:00 to 23:59
Assignable END times:From 00:00 to 24:00
3. Click the SET button.
4. Click the mode SETUP button. The PROG1-4 No.1-4
window opens.
Recording Mode Setup (PROG1-4
NO.1-4 SETUP)
Parameters for internal timer recording are assigned to
each event (NO.1-4) of the program (PROG1-4) in this win-
dow. There are five recording modes available: super fine
(SF), fine (FQ), normal (NQ), long-time (EX) and optional
(SP). If combined with audio recording (-A), the number of
recording modes doubles. The selected recording mode
determines the remaining recording time displayed on the
monitor.
In the SP mode, the field rate and picture quality are vari-
able, and can be selected at option in the range of 0.1 to
30 FPS with five quality level options respectively. After the
recording mode is selected, the available recording time is
determined and displayed.
N/A
Rec Mode Quality Audio Record Note
SF-xxxH Super Fine N/A
Field rate, quality
selected optionally Field rate, quality
selected optionally N/A
N/A
N/A
Available
Available
Available
Available Fine
Normal
Long time
Optional setup Super Fine
Fine
Normal
Long time FQ-xxxH
NQ-xxxH
EX-xxxH
SP-xxxHAvailable Optional setup SP-AxxxH SF-AxxxH
FQ-AxxxH
NQ-AxxxH
EX-AxxxH
Notes: 
•By selecting a recording time, the recording rate (REC
RATE) and the recording quality (REC QUALITY) will be
automatically calculated and displayed. For details,
refer to the provided booklet REC MODE TABLES for
WJ-HD220.