Panasonic Digital Device Display Pt 50lcx63 Operating Instructions

31
Basic Operation
EXIT
Notes:
•   Some channels with very weak signals may be locked into memory. If desired, these channels can be deleted man u al ly using 
the 
Manual Program feature.
•   Auto scan must be done when you select the input signal for the fi 
rst time or whenever you change the antenna confi 
guration.
Tu n i n g  c h a n n e l s
Press to select 
Auto Scan item.
Press to start 
Auto Scan. Notes:
•   If Cable Only, Antenna Only or Antenna/Cable is selected and DCM (Digital Cable Module) is...

32For assistance, please call : 1-888-VIEW PTV(843-9788) or, contact us via the web at: http://www.panasonic.com/contactinfo
Use this procedure when changing setting of receiving channels or changing the channel dis play.
To add or delete channels from either channel list (A/B) manually.
Manual channel setting
Tu n i n g  c h a n n e l s
Press MENU to display the Main Menu screen.
Press to select 
Manual Program.
Press to enter sub-menu.
Continued on the next page.
CH
CH VOL VOL
OK
Press to select...

33
Basic Operation
6
Repeat steps 6 to continue adding or deleting channels.Press to add 
channels to 
memory.
Press to exit menu.
Note:
Some channels with very weak signals may be locked into memory. If desired, these channels can be deleted manually using the 
Manual Program feature.
7
8
To add channel
To delete channel
Press to select 
Channel Add.CH
CH VOL VOL
OK
CH
CH VOL VOL
OK
Press to select 
Channel Del.CH
CH VOL VOL
OK
Press to delete 
channels from 
memory. Press to select 
CH.CH
CH VOL VOL...

34For assistance, please call : 1-888-VIEW PTV(843-9788) or, contact us via the web at: http://www.panasonic.com/contactinfo
Operation can be done from the Device Display.
  Press to 
select the 
desired 
volume 
level. Press to select the desired channel.   Press to turn the Device Display on. Press to operate the Device Display 
with the Remote Control.
1
2
3
4
Notes:
•   The channel number and volume level are stored even after the Device Display is turned off.
•   Power consumption can be reduced if...

35
Basic Operation
Channel and Program Tuning
Channel and Program tuning in digital television differs from conventional television. With  DTV, many 
programs can exist within a single 6 MHz channel. These channels behave as sub-channels within a single 
channel. When tuning to a digital channel, the Device Display will also tune to a program and will indicate 
the channel and program in the on-screen Channel Banner display.
In order to select channels properly, Auto Scan must be performed (refer to...

36For assistance, please call : 1-888-VIEW PTV(843-9788) or, contact us via the web at: http://www.panasonic.com/contactinfo
Press to select the desired 
channel. 
Or
CH
CH VOL VOL
OK
  Rapid Tuning
A - ANTENNA - B
Antenna Input (A/B) Tuning
R-TUNE
 Remote Control
 Device display Unit
Channel Up/Down Tuning
A /B button switches between the two RF antenna 
inputs, if connected. The last tuned channel in 
memory of the respective RF input is displayed.
Press to switch to previously viewed channel, 
Photo...

37
Basic Operation
The input mode changes each time this 
button is pressed.
Video 1 Signal of source connected to INPUT 1 is displayed.
Video 2 Signal of source connected to INPUT 2 is displayed.
Video 3 Signal of source connected to INPUT 3 is displayed.
Comp 1 Signal of source connected to COMPONENT VIDEO INPUT 1 is displayed.
Comp 2 Signal of source connected to COMPONENT VIDEO INPUT 2 is displayed.
Comp 3 Signal of source connected to COMPONENT VIDEO INPUT 3 is displayed.
  RGB 1 Signal of source...

38For assistance, please call : 1-888-VIEW PTV(843-9788) or, contact us via the web at: http://www.panasonic.com/contactinfo
A:135-99999
ABC
Del FAV480i
FULLVIVID
Unit Status display
Channel Banner: Minimized
Press Channel UP/DOWN or TV/ VIDEO to minimize the channel banner display. 
It will display the antenna input, channel number, and the station identifi 
cation (if 
available).
Channel Banner: Maximized
Press RECALL to maximize the channel banner display. While it is displayed, 
you can add a channel...

39
Basic Operation
  Auto shut off
To extend lamp life, if there is no signal to the set’s tuner for 5 minutes, the lamp will shut off automatically.
FREEZEInvalid operation notifi 
cation
If an invalid operation is attempted, the mark shown 
right is displayed.
Example:  Invalid operation was tried 
during FREEZE mode.
Device display operation
Add FAV / Del FAV feature
Tune to the desired channel to be added or 
deleted. This feature lets you add channels to or delete channels from the Favorite channel...

40For assistance, please call : 1-888-VIEW PTV(843-9788) or, contact us via the web at: http://www.panasonic.com/contactinfo
The color monitor will allow you to enjoy viewing the picture at its maximum size, including wide screen 
cinema format picture.
The aspect mode changes each time  ASPECT is 
pressed.
Notes:
•   When a 1080i or 720p signal is being received, the mode is set to FULL, and 
aspect switching is not possible.
•   When input mode is CARD, the mode is set to 4:3, and aspect switching is...