Panasonic Digital Device Display Pt 43lcx64 Operating Instructions

							21
Getting Start ed
OPTICAL
Manufactured under license 
from Dolby Laboratories. “Dolby” 
and the double-D symbol are 
trade marks of Dolby 
Laboratories.
Firmly connect 
the cable to 
the connector.
Connect three 
or more 
speakers for 
surround 
sound. Speakers (example) Use the diagram below to connect the Digital Audio Output of your Device Display to a Dolby Digital 
decoder.
  Dolby Digital 5.1 channel surround sound delivers digital-quality sound. Dolby Digital provides fi ve discrete 
full-bandwidth channels for front left, front right, center, surround left and surround right, plus a LFE (Low Frequency 
Effect) subwoofer channel, For a full Home Theater sound experience, an external Dolby Digital decoder and a 
multichannel amplifi er must be connected to the Digital Audio Out jack on the unit.
Procedure
Connect the Digital Audio cable from the Digital Audio 
Out jack on the unit to the Digital Audio In connection on 
the Dolby Digital decoder.
Note:
When ATSC channel is selected, the output from the Digital 
Audio Out jack will be Dolby Digital. But, if NTSC channel is 
selected, the output will be  PCM.
Digital Audio Out
Amplifi er with built in 
Dolby Digital decoders.
Installation 
						

							22For assistance, please call : 1-888-VIEW PTV(843-9788) or, contact us via the web at: http://www.panasonic.com/contactinfo
RGB OUT AUDIO OUT
COMPUTER
How to connect the RGB IN Terminals
Notes:
•  Some PC models cannot be connected to the set. A conversion adapter is required to use the RGB cable (D-SUB 15P) to 
connect a Macintosh computer to the set. There is no need to use an adapter for computers with PC / AT compatible D-SUB 
15P terminal.
•  The computer shown in the illustration is for example purposes only. Additional equipment and cables shown are not supplied 
with this set.
•  The picture will become dark if an PC signal with a vertical scanning frequency of 62 Hz is input. To obtain the optimum picture 
quality with the Device Display, a vertical scanning frequency of 60 Hz is recommended.
•  Do not set the horizontal and vertical scanning frequencies for PC signals which are above or below the specifi ed frequency 
range.
•  Select the desired RGB input position by pressing the 
TV/VIDEO button. (P. 37)
•  Similar connections are available at the RGB IN 1, 2 Terminals.
Pin No. Signal name
1R
2G
3B
4NC
5NC
6 Ground for R
7 Ground for G
8 Ground for B
1 678
39
45
1015 14 13 12 1 1
2
NC: Not connected
Installation
Pin No. Signal name
9NC
10 Ground
11 N C
12 N C
13 H D / C SY N C
14 V D
15 NC PC audio cable 
(M3 stereo mini pin) Connect a cable which matches the audio 
output terminal on the computer.
Conversion adapter 
(If necessary)
 RGB cable (D-SUB 15P)
RGB IN Terminal (D-SUB 15P) Pin Layouts
Connection port view
Connecting a PC to RGB IN 
						

							23
Getting Start ed
Installation
RGB signals that can be input
The table below lists the different types of RGB signals that can be input.
If a signal which differs greatly from any of the types listed below is input, the picture image may not be 
dis played correctly, or a black background may be displayed. At this time, “signal” will fl ash in the 
on-screen display for about 5 seconds.
Notes:
•  Input signals, other than those listed with a * mark, will give you a beautiful, stable picture.
•  The D-SUB15P connector can accept RGB (H-V sync separate) and RGB (sync on green). However, it is not guaranteed to 
display stable color when using RGB (sync on green).
•  When used with an external video processor/scaler, it must have RGB (H-V sync separate) output.
Mode typeSignal data
Information menu 
display No. of dots
(H X V)Horizontal frequency
(kHz)Vertical frequency
(Hz)
Personal Computer Signals
  VGA400 (70 Hz)    640 X 400   31.47   70.08   VGA400 70Hz
VGA480 (60 Hz)    640 X 480   31.47   59.94   VGA 60Hz
Macintosh 13″  640 X 480   35.00   66.67   MAC 13
  VESA400 (85 Hz)   640 X 400   37.86   85.08   VESA 85Hz
VESA480 (72 Hz)   640 X 480   37.86   72.81   VGA 72Hz
VESA480 (75 Hz)   640 X 480   37.50   75.00   VGA 75Hz
VESA480 (85 Hz)   640 X 480   43.27   85.01   VGA 85Hz
  SVGA (56 Hz)   800 X 600   35.16   56.25   SVGA 56Hz
SVGA (60 Hz)    800 X 600   37.88   60.32   SVGA 60Hz
SVGA (72 Hz)   800 X 600   48.08   72.19   SVGA 72Hz
SVGA (75 Hz)   800 X 600   46.88   75.00   SVGA 75Hz
SVGA (85 Hz)   800 X 600   53.67   85.06   SVGA 85Hz
Macintosh 16″  832 X 624   49.73   74.55   MAC 16
*  XGA (60 Hz)    1 024 X 768   48.36   60.00   XGA 60Hz
* XGA (70 Hz)   1 024 X 768   56.48   70.07   XGA 70Hz
* XGA (75 Hz)   1 024 X 768   60.02   75.03   XGA 75Hz
* Macintosh 19″  1 024 X 768   60.24   74.93   MAC 19
DTV Format 
Signals
  480i   664 X 485   15.73   29.97   480 i
  480p    720 X 483   31.47   59.94   480 p
  720p    1 280 X 720   45.00   60.00   720 p
* 1080i    1 920 X 1 080   33.75   30.00   1080 i 
						

							24For assistance, please call : 1-888-VIEW PTV(843-9788) or, contact us via the web at: http://www.panasonic.com/contactinfo
How to connect the  HDMI input terminal
Installation
HDMI OUT
The connector on the unit is HDMI Type A connector.
AUDIO OUTHDMI OUT
The connector on the unit is HDMI Type A connector.
About HDMI
HDMI is the fi rst all digital consumer electronics A / V interface that supports several uncompressed standard, 
enhanced and high defi nition video format as well as all existing multi-channel audio formats. One jack supports both 
video and audio information. The HDMI/HDCP
1 input can be connected to an EIA /CEA 861/861B2 compliant 
consumer electronic device, such as a set top box or DVD player equipped with a HDMI output connection. By 
inputting a High-bandwidth Digital Content Protection (HDCP) high defi nition picture source to the HDMI terminal of 
this unit, high defi nition pictures can be displayed on the screen in their digital form. The HDMI input terminal is not 
intended to be used with personal computers. This unit is compatible with 1080i, 720p and 480p formats. Select the 
output of the connected device to match that of the unit.
Notes:
1  HDMI/HDCP = High Defi nition Multimedia Interface / High-Bandwidth Digital Copy Protection.2 EIA/CEA-861/861B Profi les compliance covers profi les for transmission of uncompressed digital video including high bandwidth 
digital content protection.
Connection diagram
Follow the diagram below to connect the unit to a set top box or a DVD player.
Set top box
Set top box When audio signal input is digital.
When audio signal input is analog. 
						

							25
Getting Start ed
Installation
By inputting a High-bandwidth Digital Content Protection high-defi nition picture source to the HDMI IN terminal of 
this Device Display, high-defi nition pictures can be displayed on the screen in their digital form. (This terminal is for 
use in the future when High-bandwidth Digital Content Protection DVD players and D-VHS are put on the market.)
Notes:
• Select the HDMI input position by pressing the TV/VIDEO button. (P. 37)
• The 
HDMI IN terminal can only be used with 1080i, 720p and 480p picture signals.
•  If there is no audio, check if the source equipment has PCM output. If not, please use analog connections.
•  Be sure HDMI is securely connected. If not, picture noise and/or incorrect picture display may result.
•  With HDMI connection, depending on the signal, the picture may be displayed with unnatural colors (as if red and blue are 
reversed). See UV Timing of Page 53.
The Device display is compatible with following formats. Please set the connecting device to following format.
Procedure
Audio signal ( PCM)
When digital audio is included in the HDMI connection, the compatible sampling frequencies are 48 kHz/44.1 kHz/32 
kHz. (See page 55) Video Signal:
Display mode No. of dots Vertical scanning frequency (Hz)
1080i 1920 x 1080i 59.94 / 60
720p 1280 x 720p 59.94 / 60
480p 720 x 480p
640 x 480p59.94 / 60
59.94 / 60
•  If you cannot display the picture because your Digital Set Top Box does not have a Digital Out terminal 
setting, use the Component Video Input (or the S-Video Input or Video Input). In this case, the picture will be 
displayed as an analog signal.
Press TV/ VIDEO on the Remote Control to select HDMI input.  Connect the HDMI output from the set top box or a DVD player to the HDMI input on the back of the unit.
1
2
Compatible formats 
						

							26For assistance, please call : 1-888-VIEW PTV(843-9788) or, contact us via the web at: http://www.panasonic.com/contactinfo
Always be sure to follow the procedure given below to turn the Device Display power ON and OFF.
•  The lamp cooling fan will continue to operate for approximately 1 minute after the power is turned off. At the same time, the 
POWER indicator will blink Red.
Press POWER on Device Display or Remote Control to 
turn power on.
The Power Indicator blinks Green for about 10 seconds 
and then turns solid Green.
The Power Indicator
Notes:
•  If the POWER button is accidentally turned off during use, after power is turned back on, it may take a short period before the 
lamp automatically comes on.
•  After the unit is turned on, maximum picture brightness will be achieved in 5-10 minutes. This is normal.
•  This unit consumes approx. 20 W in OFF condition when plugged into an AC outlet.
Press  POWER on Device Display or Remote Control to 
turn power off.
Note:
When the AC Cord is unplugged, the internal cooling fan stops op er at ing. In this case, the lamp will be insuffi ciently cooled and will 
take a while to turn ON again.
Power ON
Power OFF
The Power Indicator blinks Red for about 1 minute and 
then turns solid Red.
Turning the Power ON and OFF
 POWER  button/
POWER indicator
LED ACTION
Red Power – OFF (Standby mode)
Red blink Power – OFF (Now cooling)
Green Power – ON
Green blink Power – ON (Preparing to light lamp) Power shuts off after a Black Screen is displayed for a 
few seconds.
Note:
If the POWER button is pressed during the Black Screen 
display, Power is turned back on.
Do not disconnect the power cord from the outlet and do not open the circuit breaker (unless necessary) 
while the cooling fan is still operating. Do not disconnect the power cord from the power outlet while the 
power indicator blinks Red.
POWER
SAP
LIGHT
TV/VIDEOA - ANTENNA - B
TV VCR DVD
DBS RCVR CBL AUX
Power ON / OFF 
						

							27
Basic Operation
Notes:
•  Auto scan must be done when you select the input signal for the fi rst time or whenever you change the antenna confi guration.
•  Depending on conditions, Auto scan may take a while.
For your convenience, First Time Set up menu will be displayed on screen when the set is turned on for the 
fi rst time. If needed, follow the menus and procedures displayed on-screen for setting up the features.
Input Setup
To select the confi guration of RF input depending on the signal source.
Procedure
Press VOL ► to select Cable only, Cable/Antenna, or Antenna only.
Press OK to underline your selection.
When the next screen is displayed, press OK to start the Auto Scan. All 
available channels with a signal will be programmed into memory.
Auto Scan
This feature allows you to selectively auto scan channels. You can Scan 
All, Analog only channels, or Analog & Digital channels.
Procedure
Press OK to start Auto Scan.
Notes:
•  If DCM (Digital Cable Module) is present during the First Time Setup and Antenna (A) 
is set to cable, Antenna (A) will not be scanned due to the DCM providing the channel 
map.
•  If setup is incomplete, check connection of Antenna/Cable to the RF IN Terminal, then 
try Auto Scan again. (PP. 30-31)
After Auto Scan is completed the unit tunes to the fi rst channel found 
during auto scan.
First Time Setup
First Time Setup
Input Setup     Setting    Cable Only
Auto Scan
Language         OK
CHANGE
         EXIT
MENU 
to return
First Time Setup
Input Setup     
Auto Scan
LanguageScan All
Antenna (A) Analog
Antenna (A) Analog & Digital
Antenna (B) Analog
Antenna (B) Analog & DigitalSELECT   OK
         EXIT
MENU 
to return
Power ON / OFF
Note:
No video will be displayed in this setup mode.
POWER
SAP
LIGHT
MENU
123
456
78
09
EXIT CH
CH VOL VOL
R-TUNE
PIP MIN
REW
FREEZE
TV/VCR
PIP SPLIT MOVE SWAPPIP CH
DVD/VCR CHSEARCH
OPEN/CLOSE
PLAY
PAUSE STOP RECPIP MAX
FF
PROG
TV/VIDEOA - ANTENNA - B
TV VCR DVD
DBS RCVR CBL AUX
OK
MUTEASPECTBBERECALL
Language
First Time Setup
Input Setup     Setting      English
Auto Scan
Language         OK
CHANGE
         EXIT
MENU 
to return
The language of the on-screen display is set to English as the factory setting. 
You can select English, Spanish or French as the on-screen displays language.
Procedure
Press ◄ VOL or VOL ► to select desired language, then press OK to set. 
						

							28For assistance, please call : 1-888-VIEW PTV(843-9788) or, contact us via the web at: http://www.panasonic.com/contactinfo
Pressing MENU 
displays the 
Main 
Menu screen.
Note:
Depending on the signal 
being input, some items 
may or may not be 
adjustable and some 
functions may or may not 
be available.
Basic Menu Navigation
Continued in left column of next page. Pressing 
MENU again 
displays 
previous level 
menu.
CH
CH VOL VOL
OK
Pressto select the desired 
icon.
CH
CH VOL VOL
OKPressto enter the menu.
Picture
 PicMode                 VIVID
 Color                     +32
 Tint                      +32
 Brightness                +32
 Picture                   +32
 Sharpness                 +32
 Normal                    Set
 Other Adjust SELECT    OK
  MENU    EXIT
CH
CH VOL VOL
OKPress to select desired menu item.
Picture
 PicMode                 VIVID
 Color                     +32
 Tint                      +32
 Brightness                +32
 Picture                   +32
 Sharpness                 +32
 Normal                    Set
 Other Adjust SELECT
CHANGE
  MENU    EXIT
MENU
POWER
SAP
LIGHT
MENU
123
456
78
09
EXIT CH
CH VOL VOL
R-TUNE
PIP MIN
REW
FREEZE
TV/VCR
PIP SPLIT MOVE SWAPPIP CH
DVD/VCR CHSEARCH
OPEN/CLOSE
PLAY
PAUSE STOP RECPIP MAX
FF
PROG
TV/VIDEOA - ANTENNA - B
TV VCR DVD
DBS RCVR CBL AUX
OK
MUTEASPECTBBERECALL
12 
						

							29
Basic Operation
Basic Menu Navigation
CH
CH VOL VOL
OKPress to adjust or set desired 
menu item.
Note: For Other Adjust sub-menu.
CH
CH VOL VOL
OKPress to select Other Adjust.
CH
CH VOL VOL
OKPress to access Other Adjust 
sub-menu.
CH
CH VOL VOL
OKPress to select desired sub-menu 
items.
CH
CH VOL VOL
OKPress to select desired sub-menu 
items.
Note: To EXIT menus.
Press repeatedly until normal 
picture is displayed.
Pressto return to normal picture.
EXIT
Continued from page 28.
Continued in right column.Continued from left column.
Picture
 PicMode                 VIVID
 Color                     +32
 Tint                      +32
 Brightness                +32
 Picture                   +32
 Sharpness                 +32
 Normal                    Set
 Other Adjust SELECT    OK
  MENU    EXIT
SELECT    OK
  MENU    EXIT
Other Adjust
 Color Temp             Normal
 Video NR                  Off
 3D Y/C                     On
 Color Matrix               SD
 3D I/P                    Off
 ID1                        On
SELECT    OK
  MENU    EXIT
Other Adjust
 Color Temp             Normal
 Video NR                  Off
 3D Y/C                     On
 Color Matrix               SD
 3D I/P                    Off
 ID1                        On
SELECT    OK
  MENU    EXIT
Other Adjust
 Color Temp             Normal
 Video NR                   On
 3D Y/C                     On
 Color Matrix               SD
 3D I/P                    Off
 ID1                        On
MENU
 Color      +32 
						

							30For assistance, please call : 1-888-VIEW PTV(843-9788) or, contact us via the web at: http://www.panasonic.com/contactinfo
CH
CH VOL VOL
OK
Automatically searches and adds receivable channels to memory.
Press 
MENU to display the Main Menu screen.
Press to select 
Setup icon.
Press to display 
the options in the 
Setup menu.
Press to display 
the 
Program 
Channel menu.
Press to select 
Program CH 
icon
.
Press to select 
Input Setup.
Note:
TV or Cable Tuning mode must be set according 
to your connections.
1
Automatic channel setting
Tu n i n g  c h a n n e l s
CH
CH VOL VOL
OK
CH
CH VOL VOL
OK
Press to select Cable Only, Cable/Antenna 
or Antenna Only.
Press to set.CH
CH VOL VOL
OK
2
4
Program Channel
Input Setup     Setting   Cable/Antenna
Auto Scan
Manual Program
Signal Meter
Language
  Connect Cable to Antenna (A)
  Connect Antenna to Antenna (B)
      Change your Input Setup
            and press OK
         OK
CHANGE
         EXIT
MENU 
to return
3
Program Channel
Input Setup     Setting    Cable only
Auto Scan
Manual Program
Signal Meter
Language    Auto scan is needed
press OK to start Auto scan         OK
CHANGE
         EXIT
MENU 
to return
POWER
SAP
LIGHT
MENU
123
456
78
09
EXIT CH
CH VOL VOL
R-TUNE
PIP MIN
REW
FREEZE
TV/VCR
PIP SPLIT MOVE SWAPPIP CH
DVD/VCR CHSEARCH
OPEN/CLOSE
PLAY
PAUSE STOP RECPIP MAX
FF
PROG
TV/VIDEOA - ANTENNA - B
TV VCR DVD
DBS RCVR CBL AUX
OK
MUTEASPECTBBERECALL
Press to enter 
the sub-menu.
Continued on the next page.