Panasonic Digital Device Display Pt 43lcx64 Operating Instructions

11
Getting Start ed
Location of Controls
Remote Keys DESCRIPTION
1 
POWERPress to turn ON and OFF.
2TVSets the remote to communicate with television.
VCR, DVD, AUX, 
CBL, RCVR, 
DBS
Sets the remote to communicate with other devices.
3
  TV/VIDEOChanges Input source.
4
SDAccesses the Photo Viewer feature (SD Card or PC Card).
5
  ASPECTChanges display aspect ratio.
6
  MUTEPress to mute sound.
7
  VOL ◄►Press to adjust TV sound and navigate in menus.
8
  OKPress to choose menu and sub-menu entry.
9...

12For assistance, please call : 1-888-VIEW PTV(843-9788) or, contact us via the web at: http://www.panasonic.com/contactinfo
Controls and Terminals on the Device Display
< FRONT >
  POWER button/
POWER indicator
(PP. 26, 10 0 -101)
  Volume up(+) / down(–) 
buttons
(P. 34)
  Channel up / down buttons
(P. 34)
Location of Controls
Open
A
SD CARD slotPC CARD slot Using your fi nger, 
slide Slot Cover in 
direction of arrow to 
open.
Slot Cover
Model PT-50LCX64 unit shown
TV/ VIDEO button
(P. 34)
  LAMP...

13
Getting Start ed
< REAR >
Vent
Notes:
•  Make sure the vents are not blocked. (This could cause damage.)
•  Indication on the back panel may change without notice.
Location of Controls
Vent
  Component signal input 1-3 ter mi nals
(P. 18)
AV OUT terminals
(PP. 19-20)   Input 1, 2 ter mi nals
(P. 17)   RGB Input 1 
terminal
(P. 22)
< SIDE >
Input 3 ter mi nals
(P. 17)RGB Input 2 terminal
(P. 22)
  DIGITAL AUDIO 
OUT terminal
(P. 21)  Antenna A, B terminal
(PP. 14-16)   DCM INTERFACE 
(POD INTERFACE)...

14For assistance, please call : 1-888-VIEW PTV(843-9788) or, contact us via the web at: http://www.panasonic.com/contactinfo
Connecting the Antenna / Cable to the RF IN Terminal
When using “Nut type” RF coaxial cables, tighten with fi ngers only. Overtightening may damage terminals.
•  Turn off the power supply for all com po nents before making any connections.
•  If the cables necessary for connecting a component to the system are not included with the component or available as an 
option, you may need...

15
Getting Start edAntenna Connection 
For proper reception of digital and analog VHF/UHF channels, an external antenna is required. For best reception, 
an outdoor antenna is recommended.
Connect home antenna to either ANT (A) or ANT (B) connection on back of the unit. Select Antenna mode for 
Cable/Antenna, Cable only, Antenna only or in Input Setup under Program Channel in Setup menu.
ANTENNA (A) 
TERMINAL ON THE 
BACK OF THE DEVICE 
DISPLAY Mixer
Installation
VHF Antenna
UHF Antenna
ANTENNA (B)...

16For assistance, please call : 1-888-VIEW PTV(843-9788) or, contact us via the web at: http://www.panasonic.com/contactinfo
Installation
Digital Cable Module Connection
This module allows you to tune digital and high defi nition cable channels through the cable antenna. 
Consult your Cable company on the availability of this module (also called Point of Deployment (POD) 
module). 
Notes:
•  A Digital Cable Subscription is required. (See page 84)
•  Do not insert a PC card into the DCM INTERFACE (POD...

17
Getting Start edHow to connect the “1, 2, 3” Input Terminals
Connects  VCRs and other peripheral equipment
Similar connections are available at the INPUT 1, 2, 3 input terminals.
Notes:
•  Input 3 is located on the side of the unit. 
•  Select the desired VIDEO input position by pressing the TV/VIDEO button. (P. 37)
•  When connecting video cables, priority is given to the S-Video cable when the S-Video input terminal and the video input 
terminal are connected at the same time.
Similar connections...

18For assistance, please call : 1-888-VIEW PTV(843-9788) or, contact us via the web at: http://www.panasonic.com/contactinfo
How to con nect the COMPONENT VIDEO Input Terminals
Notes:
•  Similar connections are available at the COMPONENT VIDEO INPUT 1-3 Terminals.
•  Select the desired COMPONENT VIDEO INPUT position by pressing the TV/VIDEO button. (P. 37)
•  Component video signals that can be input are  480i,  480p,  720p, and  1080i.
Because each Y, PB, and PR signal is input independently, the...

19
Getting Start edHow to connect the AV OUT Te r m i n a l s
OrInstallation
Recording Equipment
(S-VHS /VHS  VCR)
S-VIDEO
VIDEO
AU DIO
You can connect a VCR to the AV OUT terminal to record the program you are viewing on-screen. An 
external monitor can also be connected to the AV OUT terminals. Connect the VCR as shown below.
Notes:
•  This unit contains Video and Audio Outputs for the purpose of recording television programming to VCR. Due to license restrictions, 
if a device (STB, DVD, etc.) is...

20For assistance, please call : 1-888-VIEW PTV(843-9788) or, contact us via the web at: http://www.panasonic.com/contactinfo
How to connect the Amplifi er
Installation
Analog Audio Out
Stereo System 
(A Stereo Amplifi er and Speakers) 
AU DIO
To listen to the audio through a separate  stereo system, connect an external audio amplifi er to AUDIO OUT 
on back of unit.
Note:
AUDIO OUT terminals cannot be connected directly to external speakers.
Audio Adjustments
•  Select Speakers Off in Audio menu under Other...