Panasonic Digital Camera Dmc Zr1 Operating Instructions For Advanced Features

							- 141 -
Connecting to other equipment
Printing the Pictures
If you connect the camera to a printer supporting PictBridge, you can select the pictures to 
be printed out and instruct that printing be started from the camera’s LCD monitor.
Preparations:
Turn on the camera and the printer.
Remove the card before printing the pictures from the built-in memory.
Perform the print quality and other settings  at the printer before printing the pictures.
Set the mode dial to anything except [ ¨].
A USB connection cable (supplied)•Check the directions of the connectors, and plug them straight in or unplug them straight out. 
(Otherwise the connectors may be bent out of shape which may cause malfunction.)
B Align the marks, and insert.
•Use a battery with sufficient battery power or the AC adaptor (optional) and DC coupler 
(optional). If the remaining battery power becomes low while the camera and the printer are 
connected, the status indicator blinks and the alarm beeps. If this happens during printing, stop 
printing at once. If not printing, di sconnect the USB connection cable.
Connect the camera to a printer via the USB connection cable  A 
(supplied).
•When the camera is connected to the printer, the cable disconnect prohibit icon [ å] 
appears. Do not disconnect the USB cable while [ å] is displayed.
Press  3/4 to select [PictBridge(PTP)], and then 
press [MENU/SET].
0â0÷0Á0ð0ö0õ0Ð
0å0ê0è0ê0õ0â0í
USB MODE
SELECT SET
PLEASE SELECT 
THE USB MODE
PictBridge(PTP)PC 
						

							Connecting to other equipment
- 142 -
Note
•This unit cannot be stood upright when the AC adaptor is connected. When placing it down and 
operating, we recommend placing it on a soft cloth.
•Do not use any other USB connection cables except the supplied one.
Use of cables other than the supplied USB connection cable may cause malfunction.
•Turn the camera off before connecting or disconnecting the AC adaptor (optional).•Before inserting or removing a card, turn the camera off, and disconnect the USB connection 
cable.
•You cannot switch between the built-in memory and the card while the camera is connected to 
the printer. Disconnect the USB connection cable, insert (or remove) the card and then connect 
the USB connection cabl e to the printer again.
•Copy the pictures recorded in Clipb oard Mode, copy them onto a card ( P 111 ), and then print 
them out.
Selecting a single picture and printing it
Press  2/1 to select the picture and then press 
[MENU/SET].
•The message disappears in about 2 seconds.
Press  3 to select [PRINT START] and then press 
[MENU/SET].
•Refer to  P144 for the items which can be set before starting to 
print the pictures.
•Press [MENU/SET] to cancel printing halfway.•Disconnect the USB connecti on cable after printing.
PictBridge
MULTI PRINT
100-0001
100-0001
PLEASE SELECT
THE PICTURE TO PRINT
SELECTPRINT
12
OFF
1
CANCEL SELECT SET
PRINT START
PRINT WITH DATE
NUM. OF PRINTS
PAPER SIZE
PAGE LAYOUT
SINGLE SELECT 
						

							- 143 -
Connecting to other equipment
¢Only when [FAVORITE] is at [ON] and when there are pictures set as favorites.  (P131)
Selecting multiple pictures and printing them
Press  3.
Press  3/4 to select an item and then press [MENU/
SET].
•If the print check screen has appeared, select [YES], and print 
the pictures.
ItemDescription of settings
[MULTI SELECT] Multiple pictures are printed at one time.
•Press 
3/4/ 2/1 to select the pictures, and then When [DISPLAY] is 
pressed, [é] appears on the pictures to be printed. (When [DISPLAY] is 
pressed again, the setting is canceled.)
•After the pictures have been selected, press [MENU/SET].
[SELECT ALL] Prints all the stored pictures.
[PRINT SET 
(DPOF)] Prints the pictures set in [PRINT SET] only. 
(P132)
[FAVORITE]
¢Prints the pictures set as favorites only.  (P131)
Press 3 to select [PRINT START] and then press 
[MENU/SET].
•Refer to  P144 for the items which can be set before starting to 
print the pictures.
•Press [MENU/SET] to cancel printing.•Disconnect the USB connecti on cable after printing.
MULTI SELECT
SELECT ALL 
PRINT SET (DPOF) 
FAVORITEPictBridge
CANCEL SELECT SET
OFF
1PRINT STARTPRINT WITH DATE
NUM. OF PRINTS
PAPER SIZE
PAGE LAYOUT
MULTI SELECT
CANCEL
SELECT SET 
						

							Connecting to other equipment
- 144 -
Select and set the items both on the screen in step 2 of the 
“Selecting a single picture and printing it” and in step 3 of the 
“Selecting multiple pictures and printing them” procedures.
•
When you want to print pictures on a paper size or a layout which is not 
supported by the camera, set [PAPER SIZE] or [PAGE LAYOUT] to [ {] 
and then set the paper size or the layout on the printer. (For details, 
refer to the operating instructions of the printer.)
•When [PRINT SET (DPOF)] has been selected, the 
[PRINT WITH DATE] and [NUM. OF PRINTS] items are not displayed.
•If the printer does not support date printing, the date cannot be printed on the picture.•Since the printer’s settings may take precedence over the print with date setting, check the 
printer’s print with date setting as well.
•When printing images with a text stamp, please remember to set print with date to [OFF] or the 
date will print on top.
NoteWhen asking the photo shop to print the pictures•By stamping the date using [TEXT STAMP]  (P125) or setting date printing at the time of the 
[PRINT SET]  (P132) setting before going to a photo shop, the dates can be printed at the photo 
shop.
You can set the number of prints up to 999.
Print Settings
[PRINT WITH DATE]
ItemDescription of settings
[OFF] Date is not printed.
[ON] Date is printed.
[NUM. OF PRINTS]
OFF
1
CANCEL SELECT EXIT
PRINT START
PRINT WITH DATE
NUM. OF PRINTS PAPER SIZE
PAGE LAYOUT
MULTI SELECT 
						

							- 145 -
Connecting to other equipment
•Paper sizes not supported by the printer will not be displayed.
[PAPER SIZE]
ItemDescription of settings
{ Settings on the printer are prioritized.
[L/3.5 qk5q]
89 mmk127 mm
[2L/5 qk7q] 127 mmk178 mm
[POSTCARD] 100 mmk148 mm
[16:9] 101.6 mmk180.6 mm
[A4] 210 mmk297 mm
[A3] 297 mmk420 mm
[10 k15cm] 100 mmk150 mm
[4 qk6 q] 101.6 mmk152.4 mm
[8 qk10 q] 203.2 mmk254 mm
[LETTER] 216 mmk279.4 mm
[CARD SIZE] 54 mmk85.6 mm 
						

							Connecting to other equipment
- 146 -
•An item cannot be selected if the printer does not support the page layout.
∫Layout printing
When printing a picture several times on 1 sheet of paper
For example, if you want to print the same picture 4 times on 1 sheet of paper, set 
[PAGE LAYOUT] to [ ä] and then set [NUM. OF PRINTS] to 4 for the picture that you 
want to print.
When printing different pictures on 1 sheet of paper
For example, if you want to print 4 di fferent pictures on 1 sheet of paper, set 
[PAGE LAYOUT] to [ ä] and then set [NUM. OF PRINTS] to 1 for each of the 4 pictures.
Note
•
The camera is receiving an error message from the printer when the [ ¥] indication lights 
orange during printing. After finishing printing, make sure there are no problems with the 
printer.
•If the number of prints is high, the pictures may be printed several times. In this case, the 
remaining number of prints indicated may differ from the number set.
[PAGE LAYOUT] (Layouts for printing that can be set with this unit)
ItemDescription of settings
{ Settings on the printer are prioritized.
á 1 picture with no frame on 1 page
â 1 picture with a frame on 1 page
ã 2 pictures on 1 page
ä 4 pictures on 1 page 
						

							- 147 -
Connecting to other equipment
[PLAYBACK] Mode: ¸
Playing Back Pictures on a TV Screen
•Please use the optional AV cable (DMW-AVC1).Preparations:
Set the [TV ASPECT]. (P28)
Turn this unit and the TV off.
1 Yellow: to the video input socket
2 White: to the audio input socket
A Align the marks, and insert.
B AV cable
•Check the directions of the connectors, and plug them straight in or unplug them straight out. 
(Otherwise the connectors may be bent out of shape which will cause malfunction.)
Connect the AV cable  B to the video input and the audio input 
sockets on the TV.
Connect the AV cable to the [AV OUT] socket on the camera.
Turn the TV on and select external input.
Turn the camera on.
Note
•Depending on the [ASPECT RATIO], black bands may be displayed on the top and bottom or 
the left and right of the pictures.
•Do not use any other cables except a genuine  Panasonic AV cable (DMW-AVC1; optional).•Read the operating instructions for the TV.•When you play back a picture vertically, it may be blurry.•You can view pictures on TVs in other countries (regions) which use the NTSC or PAL system 
when you set [VIDEO OUT] in the [SETUP] menu. 
(PAL video out is not available on the version DMC-ZR1P sold in the U.S. and the version 
DMC-ZR1PC sold in Canada.)
Playing back pictures using the AV cable
0â0÷0Á0ð0ö0õ0Ð
0å0ê0è0ê0õ0â0í 
						

							Connecting to other equipment
- 148 -
Still pictures recorded on an SD Memory Card can be played back on a TV with an SD 
Memory Card slot.Note
•
Depending on the TV model, pictures may  not be displayed on the full screen.•Motion pictures cannot be played back. To play back motion pictures, connect the camera to 
the TV with the AV cable.
•You cannot play back pictures on SDHC cards if the TV does not support these cards.
Playing back pictures on a TV with an SD Memory Card slot 
						

							- 149 -
Others
OthersScreen Display
∫In recording
Recording in Normal Picture Mode [ !] (Initial setting)
1 Recording Mode
2 Flash Mode  (P56)
3 AF area  (P44)
4 Focus  (P44)
5 Picture size  (P92)
6 Quality  (P93)
7 Battery indication  (P12)
8 Number of recordable pictures  (P169)
9 Built-in memory  (P16)
: Card (P16)  (displayed only during 
recording)
10 Recording state
11 ISO sensitivity (P95)
12 Shutter speed  (P44)
13 Aperture value  (P44)
14 Optical Image Stabilizer  (P105)/ : Jitter alert  (P45)
5 5
F3.3
F3.3
F3.3
1412 34 5 6 7
8
9
11 10
12
13 
						

							Others
- 150 -
∫In recording (after settings)
15 AF Tracking  (P100)
: AF Macro Mode  (P61)
: Macro Zoom Mode  (P62)
16 White balance  (P96)
17 ISO sensitivity (P95) maximum ISO sensitivity level  (P94)
18 Color Mode  (P104)
19 Recording quality  (P83, 93)
20 Available recording time  (P82):
21 Spot AF area  (P98)
22 Name
¢1  (P73)
23 Histogram  (P55)
24 Travel date  (P31)
25 Elapsed recording time  (P82)
AF tracking operation  (P41, 100)
: Intelligent ISO (P94)
26 Current date and time/ “: Travel destination setting¢2 (P34)
: Zoom/Extended optical zoom  (P46)/Digital zoom  (P46, 104)
27 Minimum shutter speed
  (P102)28 Age¢1 (P73)
Location¢ 2 (P33)
29 Exposure compensation  (P64)
30 Power LCD  (P25)/
„ : Auto Power LCD  (P25)
31 Intelligent Exposure  (P102)
32 Burst  (P103)/ : Auto Bracket  (P65)/B : Audio recording  (P106)
33 Quick AF  (P101)/ : Continuous AF  (P101)
/: AF Lock ([UNDERWATER])  (P81)/
: AF assist lamp  (P107)
34 Number of days that have passed since the travel date  (P31)
35 Self-timer Mode  (P63)
¢
1 This is displayed for about 5 seconds when this unit is turned on in [BABY1]/[BABY2] or 
[PET] in Scene Mode.
¢2 This is displayed for about 5 seconds when the camera is turned on, after setting the clock and after switching from Playback Mode to Recording Mode.
3s
3s
3s3s
171618
15
Q
Q
1
1
19
35
30 31 32 33 34
26 25 24 23 22 21 20
29 28 27
R8m30s
WT1XW