Panasonic Digital Camera Dmc Sz5 Owners Manual For Advanced Features

- 161 -
Others
[No image to send]
•
This is displayed when there is no image to transmit due to the restriction of the destination. Check 
the file type of the image to transmit. (P113)
[Connection failed. Please retry in a few minutes.]/[Network disconnected. Transfer 
stopped.]
•
Radio waves from the wireless access point are getting weak. Perform the connection closer to the 
wireless access point.
•There is no reply from the server or it has exceeded the communication processing time. Try again...

- 162 -
Others
Troubleshooting
First, try out the following procedures (P162–175).
•
This phenomenon occurs when charging in a location where the temperature is very high or very 
low. > Reconnect the USB connection cable (supplied/optional) in a location where the ambient 
temperature (and the temperature of battery) is in a 10 oC to 30 oC (50  oF to 86 o F) range, and try 
charging again. [If you reconnect the USB connection cable (supplied/optional) when the unit is 
fully charged, the charging lamp...

- 163 -
Others
•Is there any memory remaining on the built-in memory or the card?> Delete the pictures which are not necessary to increase available space in the memory.  (P39)
•You may not be able to record for a short while after turning this unit on when using a large capacity 
card.
•The picture can become whitish if there is dirt, e.g. fingerprints on the lens.
> If the lens is dirty, turn on the camera, eject the lens barrel and gently wipe the lens surface with 
a soft, dry cloth.
> Check that the...

- 164 -
Others
•Is the ISO sensitivity high or the shutter speed slow?
(ISO sensitivity is set to [ ] when the camera is shipped. Therefore, when taking pictures indoors 
etc. noise will appear.)> Decrease the ISO sensitivity.  (P73)
> Take pictures in bright places.
•Have you set [High Sens.] in Scene Mode, or [Burst] in [Rec] menu to [ ] or [ ]? If so, the 
resolution of the recorded picture decreases slightly because of high sensitivity processing, but this 
is not a malfunction.
•When recording under...

- 165 -
Others
•This phenomenon appears when you press the shutter button halfway to set the aperture value and 
does not affect the recorded pictures.
•This phenomenon also appears when the brightness changes when the camera is zoomed or when 
the camera is moved. This is because of operation of the automatic aperture of the camera, and it is 
not a malfunction.
•The LCD monitor may flicker for a few seconds after turning this unit on. This is an operation to 
correct flicker caused by lighting such as...

- 166 -
Others
•Is the flash setting set to [Œ]?
> Change the flash setting.  (P55)
•The flash cannot be used in the following cases:–Miniature Effect Mode (P62)
–[Scenery]/[Panorama Shot]/[Night Scenery]/[Sunset]/[Glass Through] (Scene Mode)  (P63)–When recording in [Burst] (except for [ ]) (P80)
•The flash is activated twice when Red-Eye Reduction (P55) has been set.
•Has [Burst] (P80) in the [Rec] menu been set to [ ]?
•[Rotate Disp.]  (P49) is set to [ ] or [ ].
•Is there a picture on the built-in...

- 167 -
Others
•Is this a non-standard picture, a picture which has been edited using a PC or a picture which was 
taken by another maker of digital cameras?
•Did you remove the battery immediately after pict ure-taking or did you take the picture using a 
battery with a low remaining charge? > Format the data to delete the pictures mentioned above.  (P49)
(Other pictures will be deleted as well and it will not be possible to restore them. Therefore, 
check well before formatting.)
•
Is the clock in the...

- 168 -
Others
•This unit automatically adjusts the aperture during motion picture recording. At such times, the 
sound may break up. This is not a malfunction.
•Even if a compatible MP4 playback device is used, the video or sound quality of the recorded motion 
pictures may be poor, or they may not be able to be played. The recorded data may also not be 
displayed properly in certain cases.
The sound of the recorded motion pictures sometimes breaks up.
Motion pictures recorded with this model cannot be...

- 169 -
Others
•Use within the communication range of the wireless LAN network.•Connection types and security setting methods are different depending on the wireless access point.> Refer to the operating instructions of the wireless access point.
•When the radio waves are interrupted, the condition may improve by moving the location or 
changing the angle of the wireless access point.
•It may not automatically connect when the network SSID of the wireless access point is set not to 
broadcast.
> Set the...

- 170 -
Others
•The wireless access points that can be registered are up to eight.> Delete the unnecessary wireless access point.
•It may take longer time to connect depending on the Wi-Fi connection setting of the smartphone, but 
it is not a malfunction.
> Try switching the ON/OFF of the Wi-Fi function in the Wi-Fi settings of the smartphone.
•Check the information in the login screen of “LUMIX CLUB”.
http://lumixclub.panasonic.net/eng/c/
•Service user registration for the “LUMIX CLUB” is not possible...