Panasonic Digital Camera Dmc Gx85 Owners Manual For Advanced Features

							261
10. Using the Wi-Fi function
1Connect to a smartphone. (P255)
2Operate the smartphone.
You can send location information acquired with a smartphone to the camera. After 
sending the information, you can also write it on images stored  in the camera.
•
Once the location information is sent to the camera, you can al so write it on images by 
performing [Location Logging] (P233)  in the [Playback] menu.
•Location information different from that at the time of recordi ng may be written. Keep the 
following points in mind:
–Set the camera’s [Home] setting in [World Time] to your region.–Once you start recording location information with your smartph one, do not change the 
camera’s [Home] setting in [World Time].
•Location information cannot be written on images that were reco rded when the clock was not 
set.
Sending images in the camera to an SNS
1 Select  [ ].
•You can switch the images to be 
displayed by selecting the icon (
A) 
on the top left of the screen. To 
display images stored in the camera, 
select [LUMIX].
2 Touch and hold an image, and drag 
it to send it to an SNS, etc.
•
The image is sent to a web service 
such as an SNS.
Adding location information to images stored in the camera from  a 
smartphone/tablet
A Start recording location 
information
B Start recording images
C Finish recording the location 
information
D Sending and writing location 
information




2
1
4 3
(14

 
 
						

							10. Using the Wi-Fi function
262
∫Recording location information and images 1Start recording location information with the smartphone.
2Record images with the camera.3Stop recording the location information with the smartphone.
∫ Writing the location information to the images
(Preparation on the camera)
Connect to a smartphone.  (P255)
4Operate the smartphone.
•
Cautions for Use:
Be sure to pay special attention to the privacy, the likeness r ights, etc. of the subject 
when you use this function. Use at your own risk.
•The smartphone battery drains faster while location information  is being recorded.
When recording of location information is not necessary, stop i t.
•On the smartphone, you can set the acquisition interval of location information and check the 
transfer status of location information.
Refer to [Help] in the “ Image App ” menu for details.
Not available in these cases:
•Location information cannot be written to the following images  or in the following situations:–Images recorded after location information was sent to the came ra–Motion pictures recorded in [AVCHD]
–Images with location information already written to them
1 Start “ Image App ”.  (P254)
2  Select  [ ].
3  Select [Geotagging].
4  Select [ ] to start recording location information.
1  Select [ ] to stop recording the location information.
1  Start “ Image App ”.  (P254)
2  Select  [ ].
3  Select [Geotagging].
4  Select [ ] to send and write the location information.
•
Follow the on-screen messages to operate the smartphone.•Images with location information are indicated with [ ]. 
						

							263
10. Using the Wi-Fi function
Using a smartphone, you can combine motion pictures recorded with the camera’s [Snap 
Movie] function  (P176). Music can be added to motion pictures to be combined. In 
addition, you can save 
the combined motion picture or upload it on a web service.
A Record motion pictures with [Snap Movie].
B Send the recorded motion pictures.
C Edit the motion pictures.
D Combine the motion pictures, save the combined motion picture,  and send it to a web 
service.
E Combine the motion pictures, and save the combined motion pictu re.
∫Combining motion pictures by operating a smartphone
1Connect to a smartphone.  (P255)2Operate the smartphone.
•
[Snap Movie] of the “ Image App ” requires a smartphone that supp orts Android OS 4.3 or 
higher.
•The iPhone 4 does not support [Snap Movie] of the “ Image App ”.
Combining motion pictures recorded with Snap Movie according to  
your preference on a smartphone/tablet
1 Select  [ ].
2 Select [Snap Movie].
•
[Snap Movie] motion pictures with recent recording dates will b e selected and 
automatically sent to the smartphone.
•When motion pictures with recent recording dates are not availa ble, a screen that 
lets you select motion pictures will be displayed. Select motio n pictures and send 
them.
3 Edit the motion pictures.
•
Operate the smartphone to edit the motion pictures, such as rea rranging them, 
deleting those that are unnecessary or adding music to them.
•You can combine the edited motion pictures and save the combine d file on the 
smartphone or upload it on a web service.
•Read the [Help] in the “ Image App ” menu for further details on  how to operate.
  

 
						

							10. Using the Wi-Fi function
264
Displaying pictures on a TV
1Select the menu. (P54)
2Select [Via Network] or [Direct], and connect.  (P282)
3Select a device you want to connect.
•When the connection is established, the screen is displayed.
4Take or play back pictures on this unit.
•To terminate the connection, follow the steps below:
> [Setup]  > [Wi-Fi]  > [Wi-Fi Function]  > [Yes]
(You can also terminate the connection by pressing [Wi-Fi].  (P253))
•If you display pictures using the Wi-Fi function, they cannot b e output in 4K resolution. To 
output them in 4K resolution, connect the camera and the TV wit h an HDMI micro cable. (P292)
•When a TV is connected to this unit, the TV screen may temporar ily return to the status before 
the connection. Pictures are displayed again when you take or p lay back pictures.
•[Effect] and [Sound] of the Slide Show are disabled.
Not available in these cases:
•
Motion pictures and 4K burst files cannot be played back.•During Multi Playback, Calendar Playback or when selecting the  focus area of an image 
recorded with [Post Focus], images displayed on the camera are  not displayed on the TV.
You can display pictures on a TV that supports the 
Digital Media Renderer (DMR) function of the DLNA 
standard.
Preparations
Set the TV to DLNA waiting mode.
•
Read the operating instructions for your TV.
> [Setup]  > [Wi-Fi]  > [Wi-Fi Function]  > [New Connection]  > 
[Playback on TV]MENU
MENU 
						

							265
10. Using the Wi-Fi function
Sending images
When sending images, select the method for sending them after selecting [New 
Connection].
After the connection has been completed, settings for sending,  such as the image size for 
sending, can also be changed.
∫ Images that can be sent
¢1 Sending by [Send Images While Recording] is not available.
¢ 2 A motion picture recorded in [AVCHD] can be sent to [PC] if th e file size is 4 GB or smaller. It 
cannot be sent if the size is greater than 4 GB.
¢ 3 Excluding motion pictures recorded with their size set to [4K]  in [Rec Quality]
•Some images may not be played back or sent depending on the dev ice.
•Refer to the manual of the destination equipment or the web service for more information on 
how to playback pictures.
DestinationJPEGRAWMP4¢ 1AVCHD¢1, 24K Burst File¢ 1
Pictures recorded in [Post 
Focus]¢13D
[Smartphone] (P269) ±—±
¢3———
[PC] (P272) ±± ± ± ±±
[Cloud Sync. Service]  (P277) ±
—±
¢3—— ±
[Web service] (P274) ±—±
¢3—— ±
[AV device] (P271) ±—— — —±
[Printer]
¢ 1 (P270) ±—— — —— 
						

							10. Using the Wi-Fi function
266
A picture can be automatically sent to a specified device every time you take it.
•When connected with [Send Images While Recording], [ ] is 
displayed on the recording screen, and [ ] is displayed while 
sending a file.
•To terminate the connection, follow the steps below:
>   [Setup]  > [Wi-Fi] > [Wi-Fi Function]  > [Yes]
•You can terminate the connection or change the send settings 
by pressing [Wi-Fi].  (P253)
You cannot change the settings while sending pictures. Wait unt il sending is complete.
•Since the camera gives priority to recording, sending may take longer during the recording.•If you turn off this unit or the Wi-Fi connection before sending is complete, unsent pictures will 
not be resent.
•You may not be able to delete files or use the playback menu wh ile sending.
Not available in these cases:
•
You cannot send motion pictures, 4K burst files recorded with t he 4K Photo function, and 
pictures recorded in [Post Focus].
Send Images While Recording
55MENU 
						

							267
10. Using the Wi-Fi function
Images can be selected and sent after recording.
∫How to select an image(s) after selecting [Single Select] or [M ulti Select] 
•
Details of the playback menu [Favorite] or [Print Set] settings  will not be sent.
Not available in these cases:
•
Some images taken with a different camera may not be able to be  sent.•Images that have been modified or edited with a computer may no t be able to be sent.
Send Images Stored in the Camera
[Single Select] setting
1Select the picture.
2Select [Set].
[Multi Select] setting
1Select the picture.  (repeat)
•The setting is canceled when the picture is selected 
again.
2Select [OK].
•The number of pictures that can be sent by [Multi Select] 
is limited.
•To change the send settings on a screen that is displayed after  the image has been sent, 
press [DISP.]. To terminate the connection, select [Exit]. 
6HW
2. 
						

							10. Using the Wi-Fi function
268
Pressing [DISP.] after completing a connection allows you to change the settings for 
sending such as the image size for sending.
¢ 1 Only available when the destination is set to [Web service].
¢ 2 Only available when the destination is set to [PC].
¢ 3 Only available when the destination is set to [Cloud Sync. Ser vice] or [Web service].
¢ 4 Only available when the destination is set to [Cloud Sync. Ser vice].
Changing the settings for sending images
[Size]Resize the image to send.
[Original]/[Auto]
¢
1/[Change]
•If you select [Auto], the image size is determined by the 
circumstances at the destination.
•You can select the image size for [Change] from [M], [S] or [VG A].
The aspect ratio does not change.
[File Format]¢ 2[JPG]/[RAW iJPG]/[RAW]
[Delete Location 
Data]¢3
Select whether to delete the location information from images b efore 
sending them.
[ON]: Delete the location information, then send.
[OFF]: Keep the location information and send.
•This operation only deletes the location information from the i mages 
that are set to be sent.
(The location information will not be deleted from the original  images 
stored in this unit.)
[Cloud Limit]¢ 4
You can select whether to send images when the Cloud Folder run s 
out of free space.
[ON]: Do not send images.
[OFF]: Delete images from the oldest ones, then send new images. 
						

							269
10. Using the Wi-Fi function
Sending images to a smartphone/tablet
1Select the menu. (P54)
2Select [Via Network] or [Direct], and connect.  (P282)
3Select a device you want to connect.4Check the send settings, and select [Set].
•To change the send setting, press [DISP.]. (P268)
Preparations
•
Install the “ Image App ” in advance. (P254)
> [Setup]  > [Wi-Fi]  > [Wi-Fi Function]  > [New Connection]  > 
[Send Images While Recording] or [Send Images Stored in the Cam era] > 
[Smartphone]
On your smartphone
When connecting with [Via Network]:
1 Turn on the Wi-Fi function.
2 Select the wireless access point you want to connect to, and se t.
3 Start “ Image App ”.  (P254)
When connecting with [Wi-Fi Direct] or [WPS Connection] in [Dir ect]:
1 Start “ Image App ”.  (P254)
When connecting with [Manual Connection] in [Direct]:
1 Turn on the Wi-Fi function.
2 Select the SSID that matches the one displayed on the screen of  this unit.
3 Start “ Image App ”.  (P254)
5When [Send Images While Recording] has been selected
Take pictures. (P266)
When [Send Images Stored in the Camera] has been selected
Select the picture.  (P267)
MENU 
						

							10. Using the Wi-Fi function
270
Printing Wirelessly
1Select the menu. (P54)
2Select [Via Network] or [Direct], and connect.  (P282)3Select a printer you want to connect.
4Select pictures, and then print.
•The procedure for selecting pictures is the same as the one for  when the USB connection 
cable is connected.  (P302)
•To terminate the connection, press [ ].
(You can also terminate the connection by pressing [Wi-Fi].  (P253))
Not available in these cases:
•
Motion pictures, 4K burst files, and pictures recorded with [Po st Focus] cannot be printed.
You can send images to a compatible printer, and print 
them wirelessly.
Preparations
To print out recorded pictures wirelessly, you must use a print er that supports PictBridge 
(wireless LAN)
¢.¢ Compliant with the DPS over IP standards.
•For details on the PictBridge (wireless LAN-compatible) printer , contact the respective 
company.
>  [Setup]  > [Wi-Fi]  > [Wi-Fi Function]  > [New Connection]  > 
[Send Images Stored in the Camera]  > [Printer]MENU