Panasonic Digital Camera Dmc Gf6 Owners Manual For Advanced Features

311
Others
•When recording under fluorescent or LED lighting fixture, etc., increasing the shutter speed 
may introduce slight changes to brightness and color. These are a result of the characteristics 
of the light source and do not indicate a malfunction.
•When recording subjects in extremely bright locations or recording under fluorescent lighting, 
LED lighting fixture, mercury lamp, sodium lighting, etc., the colors and screen brightness may 
change or horizontal striping may appear on the screen....

312
Others
•You may not be able to record for a short while after turning this unit on when using a large 
capacity card.
•Use a card with SD Speed Class with “Class 4” or higher when recording motion pictures.•Depending on the type of the card, recording may stop in the middle.> If motion picture recording stops during use of a card of at least “Class 4” or if you use a 
card on which recording and deleting have been repeated many times, or a card that has 
been formatted on a PC or other equipment, the...

313
Others
•Depending on the lens used, picture may be warped slightly or you may see colors along the 
edge depending on the zoom factor, due to the char acteristics of the lens. Also, the peripherals 
of the image might look warped because the perspective is enhanced when the wide angle is 
used. This is not a malfunction.
•The Optical Image Stabilizer function of the interchangeable lens (H-PS14042, H-FS1442A, 
H-FS45150) only works correctly with supported cameras. > When older Panasonic digital...

314
Others
•Check [Monitor Luminance] setting. (P50)•Perform [Monitor Display]. (P50)
•This occurs due to the aperture of the lens changing when the shutter button is pressed 
halfway, or when the brightness of the subject changes. This is not a malfunction.
•This is not a malfunction.
These pixels do not affect the recorded pictures.
•In dark places, noise may appear to maintain the brightness of the monitor.
Monitor
The Monitor is too bright or dark.
It may flicker for an instant or the brightness of...

315
Others
•You can display the pictures without being rotated when [Rotate Disp.] (P217) is set to [OFF].•You can rotate pictures with the [Rotate] function.  (P217)
•Did you press [(]?
•Is the card inserted?•Is there a picture on the card?•Is this a folder or picture which was processed in the PC? If it is, it cannot be played back by 
this unit.
> It is recommended to use the “ PHOTOfunSTUDIO ” software in the CD-ROM (supplied) to 
write pictures from PC to card.
•Has [Playback Mode] been set for...

316
Others
•Is it a picture that has been recorded with other equipment? In such cases, these pictures may 
be displayed with a deteriorated picture quality.
•When Red-Eye Removal ([ ], [ ]) is in operation, if you take a picture of a subject with 
red color surrounded by a skin tone color, that red part may be corrected to black by the 
Red-Eye Removal function.> It is recommended to take a pictures with the flash closed, Flash Mode set to [ ‰], or 
[Red-Eye Removal] set to [OFF].  (P182)
•Motion...

317
Others
•Use within the communication range of the wireless LAN network.•Connection types and security setting methods are different depending on the wireless access 
point.> Refer to the operating instructions of the wireless access point.
•When the radio waves are interrupted, the condition may improve by moving the location or 
changing the angle of the wireless access point.
•It may not automatically connect when the network SSID of the wireless access point is set not 
to broadcast.
> Set the...

318
Others
•It may take longer time to connect depending on the Wi-Fi connection setting of the 
smartphone/tablet, but it is not a malfunction.> Try switching the ON/OFF of the Wi-Fi function in the Wi-Fi settings of the smartphone/
tablet.
•Check the information in the login screen of “LUMIX CLUB”.
http://lumixclub.panasonic.net/eng/c/
•Service user registration for the “LUMIX CLUB” is not possible in the environment without a 
wireless access point.
•When the firewall of the OS, security software,...

319
Others
•Upload may not complete when it is disconnected while transmitting the image.
•It may take some time after uploading the image to be reflected in the web service depending 
on the status of the server.> Wait for a while and try again.
•You can check the transmission status on the web service link settings by logging into “LUMIX 
CLUB”.
•The images in the web service cannot be saved (downloaded) to this unit. Do not delete the 
uploaded images, and make a backup of them.
•The images uploaded...

320
Others
• Is the size of the image too large?> Transmit after dividing the motion picture with [Video Divide]  (P213).
> Reduce the image size at [Size]  (P266), and then send.
> Image cannot be transmitted when the battery indicator is flashing red.
•File format of the motion picture that can be sent differs depending on the destination.  (P235, 
239,  240, 243, 247, 251)
• Is the size of the image too large?
> Transmit after dividing the motion picture with [Video Divide]  (P213).
•Sending may fail...