Panasonic Digital Business System Section 300 Installation Guide

CPC-B 
WI .o 
DATA TABLES  

Initial Settings - Data Tables V1.0 
‘i / Initial Settings - Data Tables, Version 1.0 
,i’ ’ 
3 1 AddreSS 
Feature Default 
Page 
FF I KEY - System Programming 3 
FFl-2#- 3 
l-2#-l#-22#-(0 or l-15)# Attendant overflow 8 calls 3 
l-2#-l#-23#-(0 or l)# Delayed-ring capability Disable 3 
l-2#-2#-lO#-(0 or l)# RAl baud rate switch 1200 baud 4 
FFl-3X- 5 
l-3#-20#-(0 or l-8)# Outbound ground detection timer 4 seconds 5 
l-3#-21#-(0 or l-8)# incoming ground detection timer 4 seconds 5 
FF 2 KEY - Trunk...

FF 1 KEY 
SYSTEM PROGRAMMING 
“- :._“: VI ‘0  

FF 1 Key System Programming V1.0 
COMMON SYSTEM SETTINGS 
i 
 
ATTENDANT OVERFLOW 
FFl-2#-l#-22#-(0 or l-15)# 
0#: No stacked calls 
l#: 1 call 
2#: 2 calls 
3#: 3 calls 
4#: 4 calls 
5#: 5 calls 
6#: 6 calls 
7#: 7 calls 
j3#: 8 calls 
9#: 9 calls 
lO#: 10 calls 
ll#: 11 calls 
12#: 12 calls 
13#: 13 calls 
14#: 14 calls 
15#: 15 calls - 
Determines the maxImum number of incoming calls 
that can be stacked 
to the frost attendant. The 
overflow calls are transferred to other stations set 
in the...

FF 1 Key System Programming V1.0 
COMMON SYSTEM SETTINGS 
RAIBAUDRATESWlTCH 
FFl-2#-2X-10%-(0 or l)# 
The baud rate that serves the system’s remote 
administration capability can be switched to 
O#: 300 Baud 
(RN-A or RAI-B) either 300 or 1200 baud when the RAI B card 
l#: 1200 Baud IRAI-Bl is installed 
. 
The settings for Data Length and Stop-Bit Length 
are the sane for both TTY and FM. However, the 
No Parity Check setting is always fixed on the RAI 
regardless of the TIY settings. 
Page 4  

FF 1 Key System Programming V1.0 
DETECTION TIMERS 
OUTBOUND GROUND DETECTION TIMER 
FFl-3620#-(0 or l-8)# 
0#: No detection 
l#: 1 second 
2#: 2 seconds 
3#: 3 seconds 
4#: 4 secon& 
5#: 5 seconds 
6#: 6 seconds 
7#: 7 seconds 
8#: 8 seconds The system sends a ground signal to .the ground-start 
trunk and wafts for a return ground signal from the 
telephone company’s central office. 
The returning ground signal activates the detection 
timer and the system starts the outgoing process. 
If a return...

FF 2 KEY 
TRUNK PROGRAMMING 
VI .o  

FF 2 Key Trunk Programming V1.0 
SWITCHES 
LOOP-START/GROUND-START SWITCH 
FF2-(Ol-64)#-21%-(0 or l)% 
Trunk-by-trunk switching for either the loop-start 
or ground-start circuit allows a flexible trunk setup 
between the two trunks. 
O#: Loowstart trunk 
l#: Ground-start trunk 
When the ground-start trunk is enabled, check the 
parameters for the Outbound Ground Detection 
Timer and the Inbound Ground Detection Timer. 
Install loop-start/ground-start trunk card V-B-4353 1. 
Page 6  

FF 4 KEY 
RING ASSIGNMENT 
il ) 
AND 
HUNT GROUPS 
VI .o  

FF 4 Key Ring Assignment and Hunt Groups V1.0 
DELAYED-RING TABLES 
DAYTIME DEWIYED-RXNG TABLE!3 
FF4-5#-(OOl-145)#-(01-64)#-(0 or l)# 
0#: No rim sim& 
l#: Ring signal Assigned extensions will ring at this table when 
there is no answer at the extensions assigned to 
the Daytime CO-Line Ring Tables. 
Port 145 Is for Universal Night Answer KJNAI 
NIGHTTIME DELAYED-RING TABLES 
FF4-6#-(OOl-145)#-(01-54)#-(0 or 1)# 
0#: No rim2 simal 
l#: Ring signal Assigned extensions will ring at this table when 
there...