Panasonic Cs Mk7nku 9nku Operating Instructions Manual

10
REMOTE CONTROLLER (CONTINUED)
USING THE REMOTE CONTROLLER
Temperature Display Selector
buttonThis switches the temperature display between °C and °F.
Time Display Selector buttonThis switches the time display between 24-hour time and 12-hour time.
ACL button (ALL CLEAR)Puts the remote controller into pre-operation status. Always press this button 
after replacing the batteries.
ADDRESS switch• The address switch changes to prevent mixing of signals from remote 
controller’s when two air conditioners...

11
USING THE REMOTE CONTROLLER (CONTINUED)
How to Use the Remote
ControllerWhen using the remote controller, always point the unit’s transmitter head directly 
at the air conditioner’s receiver.
Remote Controller Installation
PositionThe remote controller may be operated either from a non-fixed position or from a 
wall-mounted position. To ensure that the air conditioner operates correctly, do 
not install the remote controller in the following places:
• In direct sunlight
• Behind a curtain or other...

12
OPERATION WITH THE REMOTE CONTROLLER
1.  Operation
Check that the circuit breaker on the power panel is turned on.
Press the setting buttons as described below and change the settings as desired.
STEP 1Press the MODE selector button and select the desired mode.
For dehumidifying operationo
For cooling operationo
For fan only operationo
STEP 2To start the air conditioner, press the ON/OFF operation button.
STEP 3Press the TEMP. setting buttons to change the temperature 
setting to the desired...

13
OPERATION WITH THE REMOTE CONTROLLER (CONTINUED)
• Choose the best position in the room for the remote controller, which also acts 
as the sensor for room comfort and transmits the operating instructions. Once 
you’ve found this best position, always keep the remote controller there.
• This appliance has a built-in 5-minute time delay circuit to ensure reliable 
operation. When the operation button is pressed, the compressor will start 
running within three minutes. In the event of power failure, the...

14
OPERATION WITH THE REMOTE CONTROLLER (CONTINUED)
4.  Night Setback Mode
Night Setback Mode is used for saving energy.
Press the NIGHT SETBACK button while unit is operating. 
The   mark appears in the display.
To release the night setback function, press the NIGHT SETBACK button again.
Pressing the MODE selector button cancels Night Setback mode.
In Cooling and DRY 
Mode: ( and  )
NOTE
When the night setback mode is selected, the air conditioner automatically 
raises the temperature setting 2 °F when...

15
OPERATION WITH THE REMOTE CONTROLLER (CONTINUED)
         
5.  QUIET Mode
QUIET Mode is used to reduce the fan sound of the indoor unit. 
Press the QUIET button.
The   mark appears in the display.
To cancel, press QUIET button again.
• In QUIET Mode, the fan rotates at a slower speed than the fan speed setting.
• If the unit is already operating with a very low airflow, the fan sound may not 
change even if the QUIET button is pressed.
6.  HIGH POWER Mode
HIGH POWER mode can be used to increase the...

16
SPECIAL REMARKS
How it works?• Once the room temperature reaches the level that was set, the unit’s operation 
frequency is changed automatically.
• During DRY operation, the fan speed automatically runs at lower speed for 
providing a comfortable breeze.
• ‘‘DRY’’ operation is not possible if the indoor temperature is 59 °F or less.
• Sometimes the indoor unit may not get to the set fan speed such as LOW and 
QUIET under cool operation at very low outdoor temperatures due to the 
indoor unit being...

17
SETTING THE TIMER
In the descriptions below, the following settings are used for the temperature and 
time indicator selector button on the bottom front section of the remote controller.
• Temperature: °F
• Time: AM, PM
1.  How to set the present 
time(Example) To set to 10:30 pm.
2.  How to set the OFF time(Example) To stop the air conditioner at 11:00 am.
NOTE
Operation Indication
1.Press the CLOCK button once if 
the time indicator is not flashing.The time indication alone flashes.
2.Press the...

18
SETTING THE TIMER (CONTINUED)
3. How to set the ON time(Example) To start operation at 7:10 am.
4. How to set DAILY ON/OFF 
REPEAT timer(Example) To start operation at 7:10 am. and stop the air conditioner at 11:00 am.
To cancel a timer program• Press the CANCEL button.
• When either an ON or OFF timer is to be canceled, press the button 
corresponding to the timer whose program is to be canceled, and then press 
the CANCEL button.
• The airflow direction, fan speed and temperature setting can be...

19
USING THE 1-HOUR OFF TIMER
TIPS FOR ENERGY SAVING
1. 1-Hour OFF Timer This function causes the unit to operate for one hour and then stop, 
regardless of whether the unit is on or off when this button is pressed.
The   indicator in the display indicates that this function is operating.
Setting procedure:
Regardless of whether the unit is operating or stopped, press the 1 HR. TIMER 
button.
 appears in the display.
Cancellation procedure:
Press the ON/OFF operation button to turn the unit off, wait for...