Home > Panasonic > Microwave Oven > Panasonic Commercial Microwave Ovens Ne C1153 Operating Instructions

Panasonic Commercial Microwave Ovens Ne C1153 Operating Instructions

    Download as PDF Print this page Share this page

    Have a look at the manual Panasonic Commercial Microwave Ovens Ne C1153 Operating Instructions online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 10737 Panasonic manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							- 11 -
    Hot Surfaces
    Exterior oven surface and the oven door is very hot
    after heating. Take great care when removing hot food.
    Use oven gloves.
    Multi-Stage (Sequential) Heating
    The oven can be programmed with up to 3 different
    functions to operate in sequence. These can be
    MICROWAVE, CONVECTION or COMBINATION
    programs.
    For 2 stage programming:
    Repeat steps 1-3 on page 10, enter the next heating
    program, then press Start Pad.
    For 3 stage programming:
    Follow 2 stage programming and enter a 3rd heating
    program before pressing Start Pad.
    Changing the Heating Time
    The heating time can be increased or decreased
    during cooking by turning Timer Dial.
    Recalling Set Temperature
    The temperature selected can be checked during
    operation by pressing the Convection Pad. The
    temperature will be displayed in the display window
    before returning to the remaining heating time, when
    pressing the pad.
    The temperature cannot be altered during a program.
    Oven Lamp
    The Oven Lamp switches off when the door is closed.
    If you want to check the food, press Lamp Pad, it will
    then illuminate for 10 seconds.
    The Oven Lamp turns on and illuminates for 1 minute
    whenever the door is opened.
    Repeat Feature
    You can repeat the same heating program if you press
    Start Pad within 1 minute of the previous program
    finishing.
    After 1 minute, if Start Pad is not pressed, the display
    returns to “0”, or goes blank if the oven door is closed.
    Stop/Reset Pad
    Before heating: One tap clears the display.
    During heating: One tap stops the heating cycle and 
    two taps clears the display.
    Note:See page 16 for operation while in Program Lock.
    Preheat
    For best results in convection mode the oven should
    be preheated. (See page 18.)
    It is useful to keep the oven condition fixed.
    PROGRAM
    1
    2
    3
    TIME MICRO
    % PREHEAT
    CONVSTAGE
    PROGRAM
    1
    2
    3
    TIME MICRO
    % PREHEAT
    CONVSTAGE
    Lamp
    Convection
    Start
    StopReset
    /
    Preheat
    Operating Oven in Convection mode
    2 stage programming
    3 stage programming 
    						
    							- 12 - CONTROLS TO  USE
    8
    7
    6
    5
    3
    2
    9
    Convection
    StartMicrowave
    Stop
    Cooling
    Lamp
    Preheat
    4
    1
    0
    Prog Lock Beep
    Reset
    /
    INFORMATION ACTION DISPLAY
    1Open Door.
    Put in Food.
    Close Door.The oven lamp will come on.
    Oven lamp turns off.
    2Press
    Convection 
    Pad.Press Convection Pad until
    required temperature appears
    in display window.
    3Press.
    Select
    Power.Select Microwave power.
    Note:It is NOT possible to
    select 100-60 % power.
    5Press
    Start Pad.Display will count down time.
    The fan turns on.
    At end of heating program,
    oven beeps, and “0” flashes
    in display window until door is
    opened.
    Remove food.
    Display repeats program
    previously set. 6Open Door.
    ACCESSORIES TO  USE
    The Ceramic Insulating Tray MUST
    be used if the cooking container is
    metal, NEVER place a metal
    container directly onto the Wire
    Rack Shelfif cooking by
    COMBINATION as arcing may
    occur and damage the dish/oven.
    Convection
    Microwave
    Start
    End of Program
    Open Door
    PROGRAM
    1
    2
    3
    TIME MICRO
    % PREHEAT
    CONVSTAGE
    PROGRAM
    1
    2
    3
    TIME MICRO
    % PREHEAT
    CONVSTAGE
    PROGRAM
    1
    2
    3
    TIME MICRO
    % PREHEAT
    CONVSTAGE
    PROGRAM
    1
    2
    3
    TIME MICRO
    % PREHEAT
    CONVSTAGE
    PROGRAM
    1
    2
    3
    TIME MICRO
    % PREHEAT
    CONVSTAGE
    PROGRAM
    1
    2
    3
    TIME MICRO
    % PREHEAT
    CONVSTAGE
    4Select Time.
    Turn Timer Dial to set a
    heating time.
    Max heating time is: 1 h
    Timer counts up in:
    30 s intervals 0-10 min
    1 min intervals 10-60 min
    PROGRAM
    1
    2
    3
    TIME MICRO
    % PREHEAT
    CONVSTAG
    3
    Operating Oven in Combination mode
    Example: To cook food at 375˚F and 30 % power for 12 minutes
    If required, preheat oven to desired temperature. (See page 18.) 
    						
    							- 13 -
    Multi-Stage (Sequential) Heating
    The oven can be programmed with up to 3 different
    functions to operate in sequence. These can be
    MICROWAVE, CONVECTION or COMBINATION
    programs.
    For 2 stage programming:
    Repeat steps 1-3 on page 12, enter the next heating
    program, then press Start Pad.
    For 3 stage programming:
    Follow 2 stage programming and enter a 3rd heating
    program before pressing Start Pad.
    Changing the Heating Time
    The heating time can be increased or decreased
    during cooking by turning Timer Dial.
    Oven Lamp
    The Oven Lamp switches off when the door is closed.
    If you want to check the food, press Lamp Pad, it will
    then illuminate for 10 seconds.
    The Oven Lamp turns on and illuminates for 1 minute
    whenever the door is opened.
    Repeat Feature
    You can repeat the same heating program if you press
    Start Pad within 1 minute of the previous program
    finishing.
    After 1 minute, if Start Pad is not pressed, the display
    returns to “0”, or goes blank, if the oven door is closed.
    Stop/Reset Pad
    Before heating: One tap clears the display.
    During heating: One tap stops the heating cycle and 
    two taps clears the display.
    Note:See page 16 for operation while in Program Lock.
    Preheat
    For best results in combination mode the oven should
    be preheated. (See page 18.)
    It is useful to keep the oven condition fixed.
    For recalling set temperature see page 11.
    PROGRAM
    1
    2
    3
    TIME MICRO
    % PREHEAT
    CONVSTAGE
    PROGRAM
    1
    2
    3
    TIME MICRO
    % PREHEAT
    CONVSTAGE
    Start
    Lamp
    StopReset
    /
    Preheat
    Caution:
    The oven does not have a NON-TIP Safety Lock on Wire Rack Shelf.
    Please be careful when removing food.
    Operating Oven in Combination mode
    2 stage programming
    3 stage programming 
    						
    							- 14 -
    The oven has 100 blank program capacity to meet your heating requirements.
    CONTROLS TO  USE
    8
    7
    6
    5
    3
    2
    9
    Convection
    StartMicrowave
    Stop
    Cooling
    Lamp
    Preheat
    4
    1
    0
    Prog Lock Beep
    Reset
    /
    INFORMATION ACTION DISPLAY
    1Open Door. The oven lamp will come on.
    2Press
    Program Key.Keep key pressed for 2
    secondsuntil “P” is displayed.
    KEEP DOOR OPEN
    3Press 
    Number Pad
    followed byPress Number Pads “0” and
    “8”. If program has been
    previously set, this will
    appear in display window.
    If program memory is empty,
    then program number will
    appear in display window.
    5Select
    Time.Turn Timer Dial until 12 min is
    displayed.
    After 3 seconds display
    returns to “0”. 6Press
    Program.Key.
    Prog
    0
    PROGRAM
    1
    2
    3
    TIME MICRO
    % PREHEAT
    CONVSTAGE
    PROGRAM
    1
    2
    3
    TIME MICRO
    % PREHEAT
    CONVSTAGE
    PROGRAM
    1
    2
    3
    TIME MICRO
    % PREHEAT
    CONVSTAGE
    PROGRAM
    1
    2
    3
    TIME MICRO
    % PREHEAT
    CONVSTAGE
    4Select 
    Power.Press Microwave Pad and
    Number Pad “6”.
    Microwave
    PROGRAM
    1
    2
    3
    TIME MICRO
    % PREHEAT
    CONVSTAGE
    100 Memory Programs
    Your oven has 100 blank programs. These can be used
    for your own heating requirements.
    Program Lock
    It is NOT possible to enter a program when Program
    Lock is set. (See page 17.)
    PROGRAM
    1
    2
    3
    TIME MICRO
    % PREHEAT
    CONVSTAGE
    Prog
    8
    +
    6
    Setting the Memory Programs
    Example: To program cooking food at 60 % power for 12 minutes
    into program 08 
    						
    							- 15 -
    Multi-Stage (Sequential) Cooking
    It is possible to program into the memory 2 or 3 stage
    program using MICROWAVE, CONVECTION, or
    COMBINATION.
    Changing a Memory Program
    To change a program simply follow steps 1-6 as
    before, entering your new program.
    INFORMATION ACTION
    1Open Door.
    Put in Food.
    Close DoorThe oven lamp will come on.
    Oven lamp turns off.
    2Press
    Number Pad
    followed byPress Number Pads “0” and “8”.
    3Press Start Pad.
    Display will count down time.
    DISPLAY
    PROGRAM
    1
    2
    3
    TIME MICRO
    % PREHEAT
    CONVSTAGE
    PROGRAM
    1
    2
    3
    TIME MICRO
    % PREHEAT
    CONVSTAGE
    PROGRAM
    1
    2
    3
    TIME MICRO
    % PREHEAT
    CONVSTAGE
    Program Lock
    If program lock is activated, cooking program starts
    immediately. There is no need to press Start Pad.
    (See page 16.)
    LOCKLock
    Start
    0
    8
    Setting the Memory Programs
    Using the Memory Programs
    Example: To select program “08” in which your desired heating program (at 60 % power
    for 12 minutes) is set 
    						
    							- 16 - CONTROLS TO  USE
    8
    7
    6
    5
    3
    9
    Convection
    StartMicrowave
    Stop
    Cooling
    Lamp
    Preheat
    4
    1
    0
    Prog Lock Beep
    Reset
    /
    2
    INFORMATION ACTION DISPLAY
    1Open Door. The oven lamp will come on.
    2Press
    Program
    Lock KeyKeep key pressed for 
    2 seconds until “P” is
    displayed.
    KEEP DOOR OPEN.
    After 2 seconds, “P L”
    appears in display window.
    After 3 seconds, display
    reverts to “0”.
    PROGRAM
    1
    2
    3
    TIME MICRO
    % PREHEAT
    CONVSTAGE
    PROGRAM
    1
    2
    3
    TIME MICRO
    % PREHEAT
    CONVSTAGE
    PROGRAM
    1
    2
    3
    TIME MICRO
    % PREHEAT
    CONVSTAGE
    PROGRAM
    1
    2
    3
    TIME MICRO
    % PREHEAT
    CONVSTAGE
    One Touch Operating Mode
    When Program Lock is activated, oven operates in “ONE TOUCH” mode
    for program “00” to “09”. Press required memory program number “0” to
    “9” and oven will immediately start.
    No need to press Start Pad.
    Note:When Program Lock is activated, it is NOT possible to use 
    Program “10” to “99”.
    Setting New Programs
    When the Program Lock is activated, it is not possible
    to enter a Memory Program, to change the Beep Tone
    or Preheat Temperature.
    LOCKLock
    How to activate the Program Lock 
    						
    							- 17 -
    INFORMATION ACTION
    1Open Door. The oven lamp will come on.
    2Press
    Program Lock Key.Keep key pressed for 2 secondsuntil “P L” is
    displayed.
    KEEP DOOR OPEN.
    After 2 seconds, “P” appears in display window.
    After 3 seconds, display reverts to “o”.
    LOCKLock
    DISPLAY
    PROGRAM
    1
    2
    3
    TIME MICRO
    % PREHEAT
    CONVSTAGE
    PROGRAM
    1
    2
    3
    TIME MICRO
    % PREHEAT
    CONVSTAGE
    Two Touch Operating Mode
    The oven reverts to 2 Touch Operating mode for
    program “00” to “09”.
    Press required memory program number then press
    Start Pad.
    Setting New Programs
    Once Program Lock is released, you can again enter
    new heating programs, change the Beep Tone and
    Preheat Temperature.
    PROGRAM
    1
    2
    3
    TIME MICRO
    % PREHEAT
    CONVSTAGE
    PROGRAM
    1
    2
    3
    TIME MICRO
    % PREHEAT
    CONVSTAGE
    It is possible to check the programs that have been entered into the oven’s 100 memory programs. With the
    door open, press Start Pad and Number Pad “1” simultaneously (the oven will make an acknowledging beep).
    After 2 seconds the display window will show each individual stage of each memory program in the order 00,
    01, 02 etc. Finally it will display the Beep Tone setting ,the program lock symbol (P L) and programed hours for
    Schedule Cleaning Service (see page 22) before clearing to “0”.
    * For example if you want to know what mode is programmed in 78,
    1. After starting to show in the display from “00” press Stop/Reset Pad.
    2. Press Number Pads “7” and “8”.
    3. Press Start Pad. (The display will show from program 78 through the following Program number.)
    How to release the Program Lock
    How to read the Program List 
    						
    							- 18 -
    Notes on Preheat and Cooling:
    !AFTER heating function has completed, oven will revert to PREHEAT function automatically.
    !If you want to cancel PREHEAT function, keep Stop/Reset Pad pressed for 2 seconds.
    !During PREHEAT or COOLING, if you have started from a blank display and want to select another function
    pad, open the door first before selecting a function.
    CONTROLS TO  USE
    8
    7
    6
    5
    3
    2
    9
    Convection
    StartMicrowave
    Stop
    Cooling
    Lamp
    Preheat
    4
    1
    0
    Prog Lock Beep
    Reset
    /
    INFORMATION ACTION DISPLAY
    1Press
    Preheat Pad.Select the required Preheat
    Temperature when display is
    blank or “0”.
    eg. 350˚F
    1 press 425˚F
    2 presses 400˚F
    3 presses 350˚F
    2Press
    Start Pad.Preheat Temperature will be
    maintained at the selected
    temperature.
    If not used, oven will
    automatically switch off after
    1 hour. (Door must remain
    CLOSED.) Once oven has
    reached Preheat
    Temperature, “P” flashes and
    beep sounds.
    3Open Door.
    Close Door
    Press 
    Start Pad.Place food in oven.
    Select program.
    eg. Convection 375˚F 15 min
    Display will count down time.
    At end of heating program, “0”
    flashes in display window and
    beep sounds until door is
    opened.
    Start
    PROGRAM
    1
    2
    3
    TIME MICRO
    % PREHEAT
    CONVSTAGE
    PROGRAM
    1
    2
    3
    TIME MICRO
    % PREHEAT
    CONVSTAGE
    4Open Door.
    Display window repeats
    program previously set.
    If Start Pad is not pressed
    within 1 minute, oven reverts
    to PREHEAT.
    Preheat
    StartPROGRAM
    1
    2
    3
    TIME MICRO
    % PREHEAT
    CONVSTAGE
    PROGRAM
    1
    2
    3
    TIME MICRO
    % PREHEAT
    CONVSTAGE
    PROGRAM
    1
    2
    3
    TIME MICRO
    % PREHEAT
    CONVSTAGE
    PROGRAM
    1
    2
    3
    TIME MICRO
    % PREHEAT
    CONVSTAGE
    PROGRAM
    1
    2
    3
    TIME MICRO
    % PREHEAT
    CONVSTAGE
    PROGRAM
    1
    2
    3
    TIME MICRO
    % PREHEAT
    CONVSTAGE
    PROGRAM
    1
    2
    3
    TIME MICRO
    % PREHEAT
    CONVSTAGEAfter 1 minute
    Caution:
    The oven does not have a NON-
    TIP Safety Lock on Wire Rack
    Shelf. Please be careful when
    removing food.
    Keeping the Oven Hot
    To assist in faster heating and browning results, the PREHEAT feature is designed to keep your oven at 425˚F, 
    400˚F or 350˚F for a hot start before using CONVECTION or COMBINATION function. 
    						
    							- 19 -
    To quickly cool the oven cavity, the oven has a Cooling Pad. The Cooling Pad can be used for defrosting or
    heating by Microwave while in PREHEAT mode.
    INFORMATION ACTION
    1Press Cooling Pad. Press Cooling Pad when the display is blank or
    “0”.
    2Press
    Start Pad.
    Once the oven has cooled.!The COOLING fan and CONVECTION fan will
    turn on.
    !The oven door can be opened or closed.
    But the oven can be cooled faster when the
    door is opened than closed.
    !The oven will cool in 2-30 min depending on
    temperature.
    The COOLING and CONVECTION fans switch off.
    DISPLAY
    PROGRAM
    1
    2
    3
    TIME MICRO
    % PREHEAT
    CONVSTAGE
    PROGRAM
    1
    2
    3
    TIME MICRO
    % PREHEAT
    CONVSTAGE
    PROGRAM
    1
    2
    3
    TIME MICRO
    % PREHEAT
    CONVSTAGEStart
    Cooling
    Cooling the Oven quickly
    Keeping the Oven Hot
    Limit Time for Preheat Function
    PREHEAT function is preset to limit to 60 minutes, at the factory.
    You can change the program to keep oven hot endlessly, by using the following instructions.
    INFORMATION ACTION
    1Open Door. The oven lamp will come on.
    2 While
    pressing Start Pad,
    press and hold Cooling Pad.“H L” appears.
    KEEP DOOR OPEN.
    DISPLAY
    PROGRAM
    1
    2
    3
    TIME MICRO
    % PREHEAT
    CONVSTAGE
    PROGRAM
    1
    2
    3
    TIME MICRO
    % PREHEAT
    CONVSTAGE
    PROGRAM
    1
    2
    3
    TIME MICRO
    % PREHEAT
    CONVSTAGE
    +StartCooling
    PROGRAM
    1
    2
    3
    TIME MICRO
    % PREHEAT
    CONVSTAGE
    After 2 seconds, “H E” appears.
    After 3 seconds, display returns to “0”. 3Keep pressing.
    * If you want to revert the PREHEAT function to limit to 60 minutes:
    1. Open the door and leave it open.
    2. While pressing Start Pad, press and hold Cooling Pad until “H E”, then “H L” appears in the display window. 
    						
    							- 20 -
    When Program Lock is activated, you can not change the Beep Tone.
    Please release the Program Lock. (See page 17.)
    INFORMATION ACTION
    1Open Door. The oven lamp will come on.
    2Press
    Program Key.Keep key pressed for 2 seconds until “P” is
    displayed.
    KEEP DOOR OPEN.
    Prog
    DISPLAY
    PROGRAM
    1
    2
    3
    TIME MICRO
    % PREHEAT
    CONVSTAGE
    PROGRAM
    1
    2
    3
    TIME MICRO
    % PREHEAT
    CONVSTAGE
    3Press
    Beep Key.Press Beep Key to choose loudness and duration
    required. (See below.)
    (eg. twice)
    Beep
    PROGRAM
    1
    2
    3
    TIME MICRO
    % PREHEAT
    CONVSTAGE
    PROGRAM
    1
    2
    3
    TIME MICRO
    % PREHEAT
    CONVSTAGE
    PROGRAM
    1
    2
    3
    TIME MICRO
    % PREHEAT
    CONVSTAGE
    After 3 seconds
    4Press
    Program Key.
    After 3  seconds
    Display returns to “0”.
    Prog
    The loudness of Beep Tone and its duration at the end of heating cycle can be set.
    There are four levels of the loudness and three levels of duration.
    The 3b-1 is preset at factory.
    How to change the Beep Tone
    No.Presses
    1
    2
    3
    4
    5
    6
    7
    8
    9
    10
    Display
    3b-1
    3b-2
    3b-3
    2b-1
    2b-2
    2b-3
    1b-1
    1b-2
    1b-3
    0b
    loudness
    Loudest
    Loudest
    Loudest
    Middle
    Middle
    Middle
    Quietest
    Quietest
    Quietest
    Silent
    duration
    beeps for 60 seconds
    short beeps 3 times
    long beeps 3 times
    beeps for 60 seconds
    short beeps 3 times
    long beeps 3 times
    beeps for 60 seconds
    short beeps 3 times
    long beeps 3 times
    ---
    Beep 
    						
    All Panasonic manuals Comments (0)

    Related Manuals for Panasonic Commercial Microwave Ovens Ne C1153 Operating Instructions