Panasonic Combination Vcr Pv C2062 Operating Instructions

							Please read these instructions carefully before attempting to connect,
operate, or adjust this product. Please save this manual.
Spanish Quick Use Guide is included.
(Guía para rápida consulta en español está incluida.)
Combination VCR
Operating Instructions
Model No.
  PV-C2062/PV-C2542
LSQT0582A
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Basic Operation
Initial Setup
TV Operation
Timer Operation
Advanced Operation
For Your Information
 Initial Setup and Connection Procedures are on pages 8 and 9.
As an ENERGY STAR® Partner,
Matsushita Electric Corporation of America has
determined that this product or product model meets
the 
ENERGY STAR® guidelines for energy efficiency.
LSQT0582A_P01-09.p6512/14/2001, 1:05 PM 1 
						

							2For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Important Safeguards and Precautions
INSTALLATION
1 POWER SOURCE CAUTIONOperate only from power source indicated on unit
or in this manual. If uncer tain, have your Electric
Utility Service Company or Video Products Dealer
verify your home power source.
2 POWER CORD PLUGFor safety, this unit has a polarized type plug (one
wide blade), or a three-wire grounding type plug.
Always hold the plug firmly and make sure your
hands are dry when plugging in or unplugging the
AC power cord. Regularly remove dust, dirt, etc.
on the plug.
POLARIZED PLUG CAUTION:The plug fits into outlet one way. If it cannot be fully
inserted, try reversing it. If it still will not fit, have an
electrician install the proper wall outlet. Do not
tamper with the plug.
GROUNDING PLUG CAUTION:The plug requires a three-hole grounding outlet.
If necessary, have an electrician install the proper
outlet. Do not tamper with the plug.
3 POWER CORDTo avoid unit malfunction, and to protect against
electrical shock, fire or personal injury:
- Keep power cord away from heating appliances
and walking traffic. Do not rest heavy objects on,
or roll such objects over the power cord.
- Do not tamper with the cord in any way.
- An extension cord should have the same type
plug (polarized or grounding) and must be
securely connected.
- Overloaded wall outlets or extension cords is a
fire hazard.
- Frayed cords, damaged plugs, and damaged or
cracked wire insulation are hazardous and
should be replaced by a qualified electrician.
4 DO NOT BLOCK VENTILATION HOLESVentilation openings in the cabinet release heat
generated during operation. If blocked, heat
build-up may result in a fire hazard or heat
damage to cassettes.
For your protection:
a. Never cover ventilation slots while unit is ON,
or operate unit while placed on a bed, sofa,
rug, or other soft surface.
b. Avoid built-in installation, such as a book case
or rack, unless properly ventilated.
5 AVOID EXTREMELY HOT LOCATIONS OR
SUDDEN TEMPERATURE  CHANGES
Do not place unit over or near a heater or
regulator, in direct sunlight, etc. If unit is suddenly
moved from a cold place to a warm place,
moisture may condense in unit and on the tape
causing damage.
6 TO AVOID PERSONAL INJURY Never place unit on support or
stand that is not firm, level,
and adequately strong.
The unit could fall causing
serious injury to a child or
adult and damage to the unit.
 Move any appliance and car t
combination with care. Quick
stops, excessive force, and uneven
surfaces may cause objects to over turn.
 Carefully follow all operating instructions.
USING THE  UNITBefore unit is brought out of storage or moved to a new location,
refer again to the INSTALLATION section of these safeguards.
1 KEEP UNIT WELL AWAY FROM WATER OR
MOISTURE, such as vases, sinks, tubs, etc.2 IF EXPOSED TO RAIN, MOISTURE, OR STRONG
IMPACT, unplug unit and have it inspected by a qualified
service technician before use.
3 ELECTRICAL STORMSDuring a lightning storm, or before leaving unit unused for
extended periods of time, disconnect all equipment from the
power source as well as the antenna and cable system.
4 WHEN UNIT IS PLUGGED IN DO NOT OPERATE IF:
- liquid has spilled into unit.
- unit was dropped or otherwise damaged.
- unit emits smoke, malodors, or noises.
Immediately unplug unit, and have it inspected by a service
technician to avoid potential fire and shock hazards.
 Never drop or push any object through openings in unit.
Touching internal parts may cause electric shock or fire hazard.
 Keep magnetic objects, such as speakers, away from unit
to avoid electrical interference.
5 USING ACCESSORIESUse only accessories recommended by the manufacturer to
avoid risk of fire, shock, or other hazards.
6 CLEANING UNITUnplug unit. Use a clean, dry, chemically untreated cloth to gently
remove dust or debris. DO NOT USE cleaning fluids, aerosols, or
forced air that could over-spray, or seep into unit and cause
electrical shock. Any substance, such as wax, adhesive tape, etc.
may mar the cabinet surface. Exposure to greasy, humid, or dusty
areas may adversely affect internal parts.
READ AND RETAIN ALL SAFETY AND
OPERATING INSTRUCTIONS. HEED ALL
WARNINGS IN THE MANUAL AND ON UNIT
SERVICE1 DO NOT SERVICE PRODUCT YOURSELFIf, after carefully following detailed operating instructions, the
unit does not operate properly, do not attempt to open or
remove covers, or make any adjustments not described in the
manual. Unplug unit and contact a qualified service technician.
2 REPLACEMENT OF PARTSMake sure the service technician uses only par ts specified
by the manufacturer, or have equal safety characteristics as
original parts. The use of unauthorized substitutes may
result in fire, electric shock, or other hazards.
3 SAFETY CHECK AFTER SERVICINGAfter unit is serviced or repaired, request that a through safety
check be done as described in the manufacturer’s service
literature to insure video unit is in safe operating condition.
OUTDOOR ANTENNA INSTALLATION1 SAFE ANTENNA AND CABLE CONNECTIONAn outside antenna or cable system must be properly
grounded to provide some protection
against built up static charges
and voltage. Section 810 of
the National Electrical Code,
ANSI/NFPA 70 (in Canada,
part 1 of the Canadian
Electrical Code) provides
 information regarding proper
grounding of the mast and supporting structure, grounding
of the lead-in wire to an antenna discharge unit, size of
grounding conductors, location of antenna discharge unit,
connection to grounding electrodes, and requirements for
the grounding electrode.
2 KEEP ANTENNA CLEAR OF HIGH VOLTAGE
POWER LINES OR CIRCUITS
Locate an outside antenna system well away from power
lines and electric light or power circuits so it will never touch
these power sources should it ever fall. When installing
antenna, absolutely never touch power lines, circuits or
other power sources as this could be fatal.
GROUND 
CLAMP
ELECTRIC
SERVICE
EQUIPMENTANTENNA LEAD 
IN WIRE
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
GROUNDING 
CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE 
GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H) NEC - NATIONAL 
  ELECTRICAL CODE
LSQT0582A_P01-09.p6512/14/2001, 1:05 PM 2 
						

							3
Safety Precautions/Mesures de sécurité
Warning : To prevent fire or shock hazard, do not expose this equipment to rain or moisture.
Caution : To prevent electric shock, match wide blade of plug to wide slot, fully insert.
Avertissement :Afin de prévenir tout risque d’incendie ou de chocs électriques, ne
pas exposer cet appareil à la pluie ou à une humidité excessive.
Attention :Pour éviter les chocs électriques, introduire la lame la plus large de la fiche
dans la borne correspondante de la prise et pousser jusqu’au fond.
This video recorder, equipped with the HQ (High Quality) System, is compatible with
existing VHS equipment. Only use those tapes with the 
 mark. It is recommended that
only cassette tapes that have been tested and inspected for use in 2, 4, 6, and 8 hour
VCR machines be used. This television receiver provides display of television closed
captioning in accordance with §15.119 of the FCC rules.
FCC WARNING  :Any unauthorized changes or modifications to this
equipment would void the user’s authority to operate.
This symbol warns the user that uninsulated voltage within the unit may
have sufficient magnitude to cause electric shock. Therefore, it is
dangerous to make any kind  of contact with any inside part of this unit.
This symbol alerts the user that important literature concerning the
operation and maintenance of this unit has been included.
Therefore, it should be read carefully in order to avoid any problems.
CAUTION: TO REDUCE THE RISK 
OF ELECTRIC SHOCK, DO NOT 
REMOVE COVER (OR BACK) 
NO USER-SERVICEABLE PARTS 
INSIDE REFER SERVICING TO 
QUALIFIED SERVICE PERSONNEL
RISK OF ELECTRIC SHOCK
DO NOT OPENCAUTION
Congratulations
on your purchase of one of the most sophisticated
and reliable products on the market today. Used
properly, it will bring you and your family years of
enjoyment. Please fill in the information below.
The serial number is on the tag located on the
back of your unit.
Date of Purchase
Dealer Purchased From
Dealer Address
Dealer Phone No.
Model No.
Serial No.Batteries
2 “AA”
Accessories
To order accessories,
call toll free 1-800-332-5368.
Remote Control
LSSQ0319 (PV-C2062)
LSSQ0341 (PV-C2542)
Loading the Batteries
Battery replacement caution Do not mix old and new batteries.
 Do not mix alkaline with manganese batteries.
Prevent Accidental Tape Erasure
Break off the tab to
prevent recording.
Record
Tab
Screwdriver
To record again.
Cover the hole
with cellophane tape.
This product utilizes both a Cathode Ray Tube (CRT) and other components that contain lead.
Disposal of these materials may be regulated in your community due to environmental
considerations. For disposal or recycling information please contact your local authorities, or the
Electronics Industries Alliance: 
Model PV-C2062
remote shown.
LSQT0582A_P01-09.p6512/14/2001, 1:05 PM 3 
						

							4For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Specifications
Display
Picture  Tube: 20 inch measured diagonal
90° deflection Picture Tube
(PV-C2062)
 25 inch measured diagonal
110° deflection Picture Tube
(PV-C2542)
VCR
Video Recording 4 rotary heads helical
              System: scanning  system
Audio Track: 1 track
Tuner
Broadcast Channels: V H F  2  ~  1 3 ,  U H F  1 4  ~  6 9
CABLE Channels: Midband A through I (14 ~ 22)
Superband J through W (23 ~ 36)
Hyperband AA ~ EEE (37 ~ 64)
Lowband A-5 ~ A-1 (95 ~ 99)
Special CABLE channel 5A(01)
Ultraband 65 ~ 94, 100 ~ 125
FM Radio
Band Range: 87.5 ~ 108.1 MHz
General
Power  Source: 120 V AC, 60 Hz
Power Consumption:
Power On
Approx. 110 watts (PV-C2062)
Approx. 136 watts (PV-C2542)
Power Off
Approx. 2.5 watts
Television System: EIA Standard NTSC color
Speaker: 1 piece
Operating  Temperature: 5 °C ~ 40 °C (41 °F ~ 104 °F)
Operating  Humidity: 10 % ~ 75 %
Weight: 23 Kg (50.6 lbs.)(PV-C2062)
31 Kg (68.2 lbs.)(PV-C2542)
Dimensions:515 (W) X 505 (H) X 474 (D) mm
20-5/16” (W) X 19-7/8” (H) X
18-11/16” (D) (PV-C2062)
634 (W) X 590 (H) X 464(D) mm
24-15/16 (W) X 23-1/4 (H) X
18-1/4 (D) (PV-C2542)
Note: Designs and specifications are subject to
          change without notice.
V I DEO  HEADS  MAY
NEED  CLEAN I NG  PL EASE   I NSERT  HEAD CLEAN I NG  CASSETTE 
OR  REFER   TO  MANUAL 
END : PLAY  KEY
Head Cleaning
Record/Playback Time
Only use tapes with the  mark in this unit.
SP (Standard Play)2 Hours40 Minutes1 Hour
5 Hours20 Minutes2 Hours LP (Long Play)
3 Hours 8 Hours SLP (Super Long Play)
Type of Video Cassette
Tape Speed
Setting
T160 T60
Unit auto adjusts clock for DST (Daylight Saving Time.)

 

 


Spring (First Sunday in April)
DST : ON =>
 Sets clock ahead one hour.

 

 


Autumn (Last Sunday in October)
DST :  ON =>
 Turns clock back one hour.
 If your area does not observe Daylight Saving
Time, select DST:OFF.
 Keep these time changes in mind when
programming the unit for timer recordings.
DST (Daylight Saving Time)
2 Hour
4  Hours
6 Hours
T120
Digital Auto Tracking
Continuously analyzes the signal and adjusts for
optimum picture quality.
Manual Tracking Control (to reduce picture noise)
Use during Playback and Slow Motion mode to
reduce picture noise. Press the 3 or 6 number key on
the remote control or CH 
 on the unit until the
picture clears up. To return to Auto Tracking, press
POWER off, then on again a few seconds later.
PanaBlack  
  Picture Tube (PV-C2542 only)
This unit uses a PanaBlackTM picture tube for better
color reproduction and picture contrast.
V-Lock Control
In Still mode, the 3 or 6 number key on the remote
control or CH 
 on the unit operate as a V-lock
control to reduce jitter.
Unit Information
Features for a Quality Picture
Playing older or damaged tapes may eventually
cause video heads to become clogged.
Head Clog Sensor
During playback this screen
appears if clogging is
detected. To  remove  screen,
press PLAY on the remote
or unit.
Use “dry” type head
cleaning cassette only.
(Part No. NV-TCL30PT is recommended.)
 Follow cleaning tape directions carefully.
Excessive use of head  cleaning tape can
shorten the video head life.
 If head clog symptoms persist, contact your
nearest Factory Service Center or authorized
Service Center. (See Page 36.)
LSQT0518A_P01-09+2.p65 11/8/2001, 8:40 AM4 
						

							5
Table of Contents
Important Safeguards and Precautions / Safety Precautions ...  2,3
Before Using .......................................................................................  4
Unit Information .................................................................................  4
Table of Contents ............................................................................... 5
Location of Controls ........................................................................... 6
Connections / Initial Setup (Ready to  Play) .................................  8,9
Reset Language, Channels, Clock, Time Zone Adjust ............. 10,11
Playback a Tape ................................................................................. 12
Record On a Tape .............................................................................. 12
Copy Your Tapes (Dubbing) ............................................................. 13
Tape Operation ...........................................................................  24~26
Special VCR Features .................................................................  27,28
V-Chip Control Feature ..............................................................  29~31
On-Screen Display (OSD) .................................................................. 34
Before Requesting Service ............................................................... 35
Servicenter List .................................................................................. 36
Limited Warranty ............................................................................... 37
Spanish Quick Use Guide / Guía para rápida consulta ...........  38,39
Index .................................................................................................. B C TV Operation ....................................................................................  14
MTS Broadcast / TV Stereo System 
  (For model PV-C2062 only)....  15
TV Timer Features ........................................................................  16,17
Closed Caption System ...............................................................  18,19
Timer Recording ...........................................................................  22,23
Basic Operation
TV Operation
Timer Operation
Advanced Operation
For Your Information
Initial Setup
FM Radio ............................................................................................  20
Picture Adjustment ..........................................................................  21
Cable Box Universal Remote Control Feature .........................  32,33
LSQT0582A_P01-09.p6512/14/2001, 1:05 PM 5 
						

							6For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Location of Controls
Remote Control Buttons (Light Tower™ Illuminated Remote Control)
 When LIGHT is pressed, available buttons in the selected mode light up and the selected mode button (COMBO
or DSSCABLE) flashes for 5 seconds. If no button is pressed, light goes out in 5 seconds to conserve batteries.
Also, by holding down a button, you can  confirm the selected mode (mode button will flash) in the dark.
 When EJECT is pressed, the tape is ejected from Cassette Compartment.
If EJECT is pressed during recording, the unit will not respond to the command.
EJECTEjects tape.
POWERTurn on or off the unit.
FM/TVReceives FM radio signal.
MUTEMutes the sound instantly.
CHANNEL UP/DOWNSelects a channel.SELECT UP/DOWNControl navigation around
on-screen menu.
ACTIONDisplays Main Menu.
NUMBER KeysSelects a channel directly.
PLAYBegins playback.
REWIND/SEARCHRewinds tape, and searches
reverse scene.
PAUSE/SLOWPauses and slow motion
and frame advance picture.
SLEEPTurns off the unit automatically.
AUDIO (For model PV-C2062 only)Selects the desired auio mode.
CM SKIP/ZERO SEARCHIn Stop mode, goes to the
counter “0:00:00.“ In Play mode,
skips over 1 to 3 minutes of tape.
NITEColor and picture intensity level are
adjusted during night time use.
SPEEDSelects recording speed.
STOPStops recording or playback.
COMBOReturns to COMBO mode.
LIGHTSee below.
DSS/CABLESets the remote to control some
basic DDS or Cable box
functions.
RAPID TUNEDisplays the last channel
you were watching.
VOLUME UP/DOWNAdjusts volume.SET/BACK SPACESets a selected menu, or goes
back to correct.
PROGRAMDisplays SET PROGRAM screen.
You can set Timer Program and
On-Timer.
TRACKING UP/DOWNReduces picture noise during
Playback and Slow Motion.
ADD/DELETEAdds or deletes a channel.
FAST FORWARDS/
SEARCH
Fast forwards tape, and searches
forward scene.
DISPLAY/ENTERDisplays the VCR status and
clock.
In DSS or CABLE mode, it may be
necessary after channel selection.
TAPE POSITIONFinds out present tape position
and amount of tape remaining.
RECRecords the program.
SEARCHGoes directly to the desired
recording. Locates end point of
recording.
COUNTER RESETResets to “0:00:00” at
the desired position.Notes
Model PV-C2062
remote shown.
LSQT0582A_P01-09.p6512/14/2001, 1:05 PM 6 
						

							7
Built-In Speaker
AUDIO VIDEO  IN  Jack
For dubbing.
POWERSee previous page.
VOLUME UP/DOWN
SET/BACK SPACE
See previous page.
CHANNEL UP/DOWN
TRACKING UP/DOWN
SELECT UP/DOWN
See previous page.
STOP/EJECTSee previous page.ACTIONPress together with REW.
REWIND/SEARCHSee previous page.ACTIONPress together with STOP.
PLAYSee previous page.REPEATRepeats a recording.
FAST FORWARD/
SEARCH
See previous page.
RECSee previous page.
PHONES JackConnect an
earphone or
headphones.
PROG  TIMER
Indicator
Lights when the
unit is set for
Timer Recording.
ON TIMER
Indicator
Lights when the
On-Timer is set.
REC IndicatorLights during
recording.
Remote SensorSee above.See
previous page.TIMER/FMSets a timer alarm up 60 min.
Enables FM Radio.
VIDEO IN AUDIO INPOWER VOL CHSTOP/EJECT REW/
PLAY/REPEATFF/ REC TIMER/FM
ACTIONR E C ON TIMERVIDEO IN AUDIO INPOWER VOL CHSTOP/EJECT REW/
PLAY/REPEATFF/ REC TIMER/FM
ACTIONR E C ON TIMERPROG TIMERPROG TIMER
VHF/UHF
Front View of the Unit and Indicators
Rear View of the Unit
AC Power PlugWhen plugged into an AC outlet, the unit
consumes 2.5 W of electric power in
OFF condition.VHF/UHF Antenna Input TerminalIn from your Antenna or Cable.
Page 8
LSQT0582A_P01-09.p6512/14/2001, 1:05 PM 7 
						

							8For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Connections/ Initial Setup (Ready to Play)
How to Connect
VHF/UHFV
H
F
/
U
H
F
UNIT
IN from
ANT./CABLE
VHF/UHF
VHF/UHF
V
H
F
/
U
H
F
Cable TV
Converter Box
IN from
ANT./CABLE
 2 /  6 / 2002   WED 12 : 00PMDST : ON
A
UTO  CLOCK   SET
CO
MPLETED
SETT I NG : CH 1 0
If AUTO CLOCK SET IS
INCOMPLETE screen
appears, set the clock using
MANUAL CLOCK SET
procedure as below.
SET             :        START         :  ACT I ON  SET  
CLOCK
DST : ON
SESET COMPLETEDCOMPLETED
2 /   6/2 /   6/:20022002WEDWED12120000PMPM
Initial Setup (Ready to Play)
1
Plug the unit power cord into an
AC wall outlet.
Press Power* on the remote or
unit. The unit comes on and auto
channel and clock set starts.
 If you use a cable box, turn it on and set it to the
Public Broadcasting Service (PBS) channel in
your time zone. If you use a DSS reciever, it
must be turned off.
Settings are made
automatically. When setup is
done, this screen appears.
For ANT./Cable
Connect the cable from
Antenna/Cable to the VHF/UHF
terminal on the unit.
For DSS/Cable Box
Connect the OUT jack on your
cable box to the VHF/UHF
terminal on the unit with a RF
cable.
WARNING:
Overtightening Nut type RF coaxial cables
may damage jacks. Finger tighten only.
Please make all cable or antenna connections before powering on.
CH AUTO SET PROCEEDING
             PROCEEDING
         AUTO CLOCK SET 
CANCEL : PRESS STOP KEY
3
Connecting
2
Press Combo on the remote for Combo
mode.
LSQT0582A_P01-09.p6512/14/2001, 1:05 PM 8 
						

							9
Initial Setup
VIDEO IN AUDIO INPOWER VOL CHSTOP/EJECT REW/
PLAY/REPEATFF/ REC TIMER/FMACTIONREC ON TIMERVIDEO IN AUDIO INPOWER VOL CHSTOP/EJECT REW/
PLAY/REPEATFF/ REC TIMER/FMACTIONR E C ON TIMERPROG TIMERPROG TIMER
Reset all unit Memory Functions
When moving unit to a new location, or if a
mistake was made in the Initial Setup section.
 Make sure a tape is not inserted in the unit.
Manual Clock Set
If AUTO CLOCK SET was incomplete, manually
set the clock as follows.
SET          :       SELECT  :            
END          :  ACT I ON  SET  
CLOCK
DST
 : ONSESELE CT    MONTHTH
1 /     /:
1
2
Press ACTION on the Remote to
display SET CLOCK Menu screen.
Press 
  to select the month
and press 
 to set. In the same
manner, select and set the date,
year, time, and DST. (Daylight
Saving Time)
SET             :        START         :  ACT I ON  SET  
CLOCK
DST : ONSESET COMPLETEDCOMPLETED
2 /   6/2 /   6/:20022002WEDWED12120000PMPM
3
Press ACTION twice to start
CLOCK and exit.
3 1
2Do “Initial Setup” on page 8.
ady to Play)
POWER
ACTION
SELECT/SET :CH UP :CH DOWN :VOL UP :VOL DOWNNote to CABLE System InstallerThis reminder is provided to call the
CABLE (Cable TV) System Installers
attention to Article 820-40 of the NEC
that provides guidelines for proper
grounding and, in particular, specifies
that the cable ground shall be
connected to the grounding system of
the building, as close to the point of
cable entry as practical.
Turn the unit
Power on.
Press and hold both PLAY and
FF on the unit for more than 5
seconds.
 The power will shut off.
 Please ignore “NO CASSETTE” warning. *Important: If a remote control button does not work when pressed, press the COMBO button
on the remote and try the button again.
Model PV-C2062 remote shown.
LSQT0582A_P01-09.p6512/14/2001, 1:05 PM 9 
						

							10For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Reset Language, Channels, Clock,         Time 
4)Press  and
press 
  to select
and set the month,
date, year, time,
and DST (Daylight
Saving Time).
5) Press ACTION
twice to 
start the
clock and exit this
mode. 3) Press 
 to select
“ANTENNA,” then
press 
 to set your
antenna system
 (“TV” or “CABLE”).
4) Press 
 to select
“AUTO SET,” then
press 
.
 After Channel Auto Set is
finished, Clock Auto Set
will be performed. (If  clock
is set manually, Clock
Auto Set will not be
performed.)(“TIME ZONE ADJUST”
appears only when auto
clock is set.)
M A I N  MENU
T VVCRLANGUAGE
SET          : ACT I ON   SELECT  :                               
T V
EX I T
CLOCKC H
T VVCRIDIOMAT V
MENU  PR I NC I PAL
CANALREL OJ SAL I R H
O L A 
F I JAR   : ACT I ONELEG I R : 
BONJOUR
 LAN
GUE
  MENU
T
 ELEMAGNET .
SORT I EHORLOGE CANAL
REGLER : ACT I ONSEL.       : 
1)Press   to
select language
icon.
2)Press ACTION
repeatedly.
For English
M A I N  MENU
T VVCR
HELLO
LANGUAGE
SET          : ACT I ON   SELECT  :                               
T V
EX I T
CLOCKC H
For Spanish
For French
Language
M A I N  MENU
T VVCR
EX I T
CLOCKC H
LANGUAGE
SET          : ACT I ON SELECT  :                              
ChannelsClock
Press ACTION*
to display MAIN MENU.
3)Press   to
select “EXIT.”
Press ACTION to
exit.1)Press 
  to
select “CH.”
M A I N  MENU
CLOCKC H
SET          : ACT I ON  SELECT  :                             
VCRT V
EX I TLANGUAGE
ANTANTENNENNA  :   :   CABLEABLEAUTO   SETCHANNEL   CAPT I ONWEAK  S I GNAL   D I SPLAY : OFF
SELECT :          SET       : SETEND       : ACT I ON  
           SET  UP  CHANNEL 
2)Press ACTION.
M A I N  MENU
VCR
CLOCKC H
SET          : ACT I ON   SELECT  :                               
T V
EX I T
C H
LANGUAGE
1)Press   to
select “CLOCK.”
AUTO  CLOCK  SETMANUNUALALT I ME  ZONE  ADJUST   : 0
SELECT :          SET       :      
END       : ACT I ON      
         SET  CLOCK 
2)Press ACTION.
1
2
3)Press  to select
“MANUAL” or
“AUTO CLOCK
SET” and press 
.
 For Auto Clock Set,
select “AUTO CLOCK
SET,” then press “SET”.
SET          :        START      :  ACT I ON  SET  
CLOCK
DST : ON2 /   6/2 /   6/:20022002WEDWED12120000PMPM
SESELE CT    HOURHOUR
SELECT  :            
LSQT0582A_P10-21.p6512/14/2001, 2:04 PM 10