Panasonic Color CCTV Camera Wv Cw504 Series Installation Guide

31
• Cord length and wire gauge
24 V AC
The  recommended  cord  length  and  copper 
wire size are shown in the table for reference. 
The  voltage  supplied  to  the  camera  should  be 
between 19.5 V AC and 28 V AC. 
Recommended wire gauge for 24 V AC line. 
Copper  wire 
size (AWG)#24 
(0.22 mm2) #22 
(0.33 mm2) #20 
(0.52 mm2) #18 
(0.83 mm2)Length of 
cable 
(approx.) m 20 30 45 75
ft 66 100 150 250
12 V DC
The  recommended  resisance  and  copper  wire 
size are shown in the table for reference....

32
Optional Heater Unit WV-CW5H (option)
Installing  the  heater  unit  enables  the  camera  to  operate  in  a  low-temperature  environment  below 
–30 °C {–22 °F}. The heater turns on automatically when the temperature inside the camera drops 
below +10 °C {50 °F} and turns off when the temperature rises. A small fan inside the unit will mini-
mize  condensation  on  the  surface  of  the  enclosure  caused  by  changes  in  ambient  temperature 
unless temperatures change too rapidly.  Important:...

33
About the setup menus
Performing  each  setting  item  in  the  setup  menu  should  be  completed  in  advance  to  use  this  unit. 
Perform the settings for each item in accordance with the conditions of the camera shooting area. 
Refer to the operating instructions (PDF) for further information. 
Setup menu list
Setup itemDescription
CAMERA ID This item specifies the camera title. The camera title that indicates th\
e 
camera location and other information about the camera is created 
with...

34
Setup itemDescription
SPECIAL CHROMA GAIN Adjusts the chroma level. 
AP GAIN Adjusts the aperture level. 
PEDESTAL Adjusts the pedestal (brightness) level. 
HUE Adjusts the chroma phase (hue) level. 
PIX OFF Corrects image defects such as flaws. 
CAMERA RESET Restores the settings in the setup menu to the default settings. 
SER.NO. Displays the serial number of this unit. 
LANGUAGE Selects a language to be used in the setup menu.
     

35
Screenshot 2
The  setup  mode  changes  to  "ENABLE",  and 
the setup menu becomes ready to be set. 
Basic operation
The description below explains how to operate the setup menu basically. 
The operations in the setup menu are performed with the operation buttons (+ page 12) after call-
ing up the setup menu on the connected video monitor.
The operations in the setup menu can also be performed through the system controller (option). 
Screenshot 1
Hold  down  the  setting  button  for  more...

36
Screenshot 3
The  selected  setup  screen  in  the  setup  menu 
appears on the screen. 
Note:
	 •	 If	 the	top	 screen	 of	the	 setup	 menu	 is	
called  up  with  the  operation  buttons  while 
a  camera  image  is  displayed,  the  setup 
mode  is  always  "DISABLE"  to  prevent 
operation  errors.  To  configure  the  settings 
in the setup menu, change the setup mode 
to "ENABLE". 
	 •	 The	cursor	is	a	reversely	highlighted	part.	
    
    **CAMERA SETUP** 
SCENE1
 ALC...

37
Screen transition diagram
 MODEL   WV-CW504
CAMERA ID     OFF
CAMERA   
SYSTEM
BACK-FOCUS   
SPECIAL
LANGUAGE
 
 END   SETUP DISABLE
    **CAMERA SETUP** 
SCENE1
 ALC          ALC    
 SHUTTER      OFF
 AGC          ON(HIGH)
 SENS UP      OFF
 WHITE BAL    ATW1
 DNR          HIGH
 BW MODE      AUTO1
 i-VMD
 RET TOP END
    **SYSTEM SETUP** 
SYNC          INT
LENS          PANASONIC
PRIVACY ZONE  OFF
STABILIZER    OFF
EL-ZOOM       OFF
UPSIDE-DOWN   OFF
 RET TOP END
  **BACK-FOCUS SETUP**  
ABF...

38
Troubleshooting
Before asking for repairs, check the symptoms with the following table. 
Contact your dealer if a problem cannot be solved even after checking and trying the solution in the 
table or a problem is not described below. 
SymptomCause/solutionReference 
pages
No image displayed
•		 Are	the	power	cord	and	coaxial	cable	
connected appropriately?
→   Check whether the connection is 
appropriately established.  30
•		 Is	the	adjusting	monitor	connected	?	
→   Check whether connection is...

39
Specifications
• Basic
Power source: 24 V AC 60 Hz, 12 V DC
Power consumption:  24 V AC:  3.4 W (without heater unit) 
14 W (with heater unit)
    12 V DC: 280 mA*
Ambient operating temperature:  –10 °C to +50 °C {+14 °F to +122 °F}
    –30 °C to +50 °C {–22 °F to +122 °F}**
Ambient operating humidity:  Less than 90 % (no condensation)
Water resistance:    Camera: IEC60529 (IP66)***
Shock resistance:   50J, IEC60068-2-75
Video output:  VBS: 1.0 V [p-p]/75 Ω, NTSC, BNC connector
Dimensions:  WV-CW504F:...

40
   Color Mode:   0.2 lx {0.02 footcandle} at F1.4 WIDE 
0.006 lx {0.0006 footcandle} (sensitivity up x32, 
at F1.4 WIDE)*
    BW mode:   0.02 lx {0.002 footcandle} at F1.4 WIDE 
0.0006 lx {0.00006 footcandle} (sensitivity up 
x32, at F1.4 WIDE)*
    * Converted value
Signal-to-noise ratio:   50 dB (AGC Off)
Dynamic range:  52 dB typ. (Super Dynamic 5 ON)
Monitor output:  VBS: 1.0 V [p-p]/75 Ω, NTSC, RCA jack
Functions:
  Camera title:  Up to 16 characters (alphanumeric characters, marks)
  Light...