Panasonic Color CCTV Camera Wv Cw504 Series Installation Guide

11
Mounting screws
	 •	 The	screws	and	bolts	 must	 be	tightened	
with  an  appropriate  tightening  torque 
according  to  the  material  and  strength  of 
the installation area.
	 •	 Do	 not	use	 an	impact	 driver.	Failure	 to	
observe this may cause overtightening and 
consequently damage to the screws.  
	 •	 When	 a	screw	 is	tightened,	 make	the	
screw  at  a  right  angle  to  the  surface.  After 
tightening  the  screws  or  bolts,  perform 
visual check to ensure tightening is enough 
and...

12
Major operating controls and their functions
q Power cord
* This illustration shows the camera  without the inner dome.
w Video output cable
e Enclosure
r Panning table
!8 ABF operation indicatorOperation
buttons
!7 Heater output connector
o Zoom lock knob i Focus lock knob
t
Tilt adjusting table
y Tilting lock screw  u Panning lock screw
!0 Camera xing screw
!1 Monitor output connector
!9 Inner dome
!2 Right button
     [(RIGHT), FAR]
!3 Left button
     [(LEFT), NEAR]
!4 Up button
     [(UP)]
!5...

13
 q  Power cord
	w  Video output cable
  e  Enclosure
  r  Panning table
    Rotate  this  table  to  adjust  the  panning 
angle of the camera.
  t  Tilt adjusting table
    Adjust the azimuth angle of the image. 
  y  Tilting lock screw 
    Locks the tilt position. 
  u  Panning lock screw
    Fixes the panning table.
  i  Focus lock knob
    Locks the focal point. 
	o  Zoom lock knob
    Locks the zoom point. 
  !0  Camera fixing screw
    Fix the attachment on the camera body. 
  !1  Monitor...

14
Connector
Lens Mounting (WV-CW504FK, WV-CW504SK)
 1.  Before mounting the lens, remove the protection sheet from the camera. 
  2.  Mount the optional lens to the camera by turning the lens clockwise.
Connector
 3.  Insert the connector of lens into the connector of the camera.  

15
Preparations
When  installing  the  camera  on  a  wall  or  a  ceiling,  there  are  two  methods  as  specified  below.  
(+ Next page)
	 •	 Using	a	two-gang	junction	box
	 •	 Using	the	mounting	base	WV-Q115
Refer  to  all  work  related  to  the  installation  of  this  product  to  qualified  service  personnel  or  system 
installer. 
	 •	 The	mounting	 base	WV-Q115	 is	optional	 for	WV-CW504F,	 WV-CW504FK.	 Use	the	screws	 sup-
plied with the camera mount bracket. 
	 •	 The	 mounting	 base...

16
Using a two-gang junction box
	 •	 When	the	camera	 is	installed	 using	the	two-gang	 junction	box,	mount	 the	camera	 attachment	
(accessory) to the embedded box installed on the wall or ceiling as a \
first step.  
Note:
  •  For wall mounting: 
    Installation  shall  be  performed  in  such  a  manner  that  "MTOP"  of  the  camera  attachment  faces 
upward. 
  •  For ceiling mounting: 
    The front side (model number indication face) of the camera shall be aligned in the direction of...

17
z Install the mounting base on the wall/ceiling.
Note:
	 •	 Only	 the	same	 type	of	holes,	 A  or B,  shall  be 
used for mounting. 
    
B B
B
A
A
A
51 mm 
{2}
ø27 mm {1-1/16}
Cable access hole
Center of mounting base
Female thread for conduit
WV-Q115
(For use of the hole A) (For use of the hole B)138 mm {5-7/16}
138 mm
{5-7/16}85 mm {3-11/32}
85 mm
{3-11/32}
(A For use of the hole)
B
B B
B A
A
A
A 

18
x   Previously run the cables from the wall or ceiling through the cable access hole. 
c   Mount the attachment onto the mount bracket. 
    Recommended tightening torque: 0.78 N·m {0.58 lbf·ft}
Camera attachment
FRONTTOP
Note:
  •  For wall mounting: 
    Installation  shall  be  performed  in  such  a  manner  that  "MTOP"  of  the  camera  attachment  faces 
upward. (Except for the case of connecting the conduit from the top. (+ page 29))
  •  For ceiling mounting: 
    The front side...

19
Camera installation
z Mount the camera. 

 q  Connect the power cord and the video output cable. (+ page 30)
  w  Align the "OPEN" mark of the camera with the protrusion of the camera attachment. 
  e  Engage  the  attachment  mounting  screw  of  the  camera  with  the  camera  mounting  hole  of  the 
camera attachment and rotate the camera in the direction of the arrow to the "LOCK" position 
to secure the camera to the camera attachment without any backlash. 
FRONTTOP
OPEN
LOCK...

20

 q  Attach the camera onto the camera attachment 
while  aligning  the  "OPEN"  mark  of  the  camera 
with the projection of the camera attachment.
Important:
	 •	 When	 mounting	the	camera	 body,	cables	 shall	
be  run  between  the  camera  attachment  and 
mounting base as indicated by the arrow in the 
illustration. 
  * Cable  running  as  indicated  by  the  arrow  is  an 
example.  Cable  running  shall  be  varied  with 
installation environment. 
    
LOCKOPEN
LOCKOPEN
Projection