Panasonic Color CCTV Camera Wv Cw500 WV CW504SE Series Installation Guide

21
 t  Mount  the  supplied  base  cover  on  the 
camera mount bracket.  
Important:
	 •	 To 	prevent 	the 	cables 	from 	being 	caught	
when the base cover is attached, keep the 
cables inside the cable guide. 
  y  Use  the  bit  for  tamperproof  screw  (acces-
sory)  to  tighten  the  fixing  screws  provided 
on both sides of the base cover. 
    (Recommended tightening torque:  
0.78 N·m)
Base cover
Base cover fixing screw 

22
x   Remove the enclosure and inner 
dome from the main body by loos-
ening the three fixing screws. 
    Loosen  the  three  fixing  screws  by  using 
the provided bit for tamperproof screw. 
    Detach  the  inner  dome  while  pushing  the 
parts with the "PUSH" indication. 
Important:
	 •	 Do	 not	hold	 the	inner	 dome	 when	carrying	
the  camera.  Otherwise,  the  camera  part 
may fall and it may damage the camera. 
Note:
	 •	 Perform	 the	same	 procedure	 when	replac-
ing  with  the...

23
Adjust the camera
z
   Be sure to view the monitor for adjustment when the camera angle is adjusted. \
    Connect  the  monitor  for  adjustment  (e.g.  a  small  LCD)  to  the  monitor  output  connector,  and 
adjust the camera angle. 
    When  determining  the  camera  angle,  repeat  fine  follow  the  adjusting  procedure  of  q, w,  and 
e shown below. 
  q Loosen the panning lock screw and rotate the camera head horizontally to adjust panning, 
and tighten the panning lock screw. 
  w Loosen...

24
x Adjusts the focus.
    Focus adjustment shall be performed when camera 
angle adjustment are performed. 
    Adjust  the  focus  by  following  the  adjusting  proce-
dure of q, w, and e shown below. 
  q Loosen  the  zoom  lock  knob  and  move  the 
knob  between  TELE  and  WIDE  to  obtain  the 
appropriate  angle  of  view,  and  then  tighten  the 
zoom lock knob. 
  w Loosen  the  focus  lock  knob,  make  coarse 
adjustment  of  the  focus,  and  then  tighten  the 
focus lock knob. 
  e...

25
v   To perform fine adjustment of the back focus after the ABF operation indi\
cator 
goes off and automatic back focus is adjusted, use the right or left button. 
Note:
	 •	 No	operation	for	10	seconds	or	more	automatically	clears	the	focus	position	indicator.	
	 •	 To	 change	 the	angle	 of	view	 by	moving	 the	zoom	 adjustment	 ring,	also	move	 the	focus	 lock	
knob to adjust the focus. 
	 •	 The	 originally	 adjusted	focus	may	be	slightly	 off	depending	 on	the	 iris	state	 resulting	 from	the...

26
b   Mount the enclosure and inner 
dome.
    Tighten  the  screws  that  have  been  loos-
ened  in  Step  2  in  page  22  using  the  sup-
plied driver bit.
    (Recommended tightening torque:  
0.78 N·m)
Important:
	 •	 Attach	 the	inner	 dome	 in	accordance	 with	
the lens direction to not to change the lens 
direction. 
	 •	 Check 	if 	the 	tabs 	of 	the 	inner 	dome 	are	
firmly fit. 
	 •	 Remove 	the 	cushioning 	(pink 	sheet) 	from	
the  inside  of  the  dome  and  the  protection 
sheet from...

27
Waterproof treatment for the cable joint sections
Adequate waterproof treatment is required for the cables when the camera with exposed cables is 
installed by means of the camera mount bracket or it is installed under the eaves. The camera body 
is waterproof, but the cable ends are not waterproof. 
Be sure to use the supplied butyl tape at the connection parts of the power cord and video output 
cable  to  apply  waterproof  treatment  in  the  following  procedure.  Failure  to  observe  this  may...

28
Important:
	 •	 If	 open	wiring	 is	conducted,	 be	sure	 to	use	 conduits	 and	run	the	cables	 inside	the	tubes	 to	pro-
tect the cables from direct sunlight. 
	 •	 When	 the	conduit	 is	connected	 at	the	 lateral	 or	bottom	 position,	 either	of	the	 arrow	 marks	 on	
the bracket shall be the top position.
	 •	 When	 the	conduit	 is	connected	 from	the	top,	 the	arrow	 mark	on	the	 attachment	 shall	be	either	
of the right or left position. 
    
    
	 •	 For	 installation	 on	the	 wall,	 do	not...

29
Make a connection
Cautions:
	 •	 ONLY	CONNECT 	WV-CW504 	TO 	24 	V 	AC 	OR 	12 	V 	DC 	CLASS 	2 	POWER 	SUPPLY.	  
(WV-CW504)
	 •	 Be	sure	to	connect	the	grounding	lead	to	the	GND	terminal.
* When using 12 V DC power supply, the optional heater unit is unavailable. To 220 V to 240 V AC
power supply (WV-CW500)
To 24 V AC/12 V DC*
power supply (WV-CW504)
Video output cable
(approx. 16 cm) Brown (Live)
Blue (Neutral)
Green/Y
ellow (GND)
To GND**
BNC connector BNC connector BNC connectorTo VIDEO IN
Power...

30
	 •	 Shrinking	the	cable-entry	 seal	is	a	onetime	
procedure.  Do  not  shrink  the  cable-entry 
seal  until  it  has  been  ascertained  that  unit 
is functioning. 
    ONLY  CONNECT  THIS  TO  24  V  AC  or  12 
V DC CLASS 2 POWER SUPPLY. 
• Cord length and wire gauge
24 V AC
The  recommended  cord  length  and  copper 
wire size are shown in the table for reference. 
The  voltage  supplied  to  the  camera  should  be 
between 19.5 V AC and 28 V AC. 
Recommended wire gauge for 24 V AC line....