Panasonic Color CCTV Camera Wv Cw500 WV CW504 Series Operating Instructions

21
Camera system setting [SYSTEM SETUP]
Performs the settings relating to the camera system such as synchronization, alarm input/output terminal, and privacy zone. 
The following settings can be configured on the "SYSTEM SETUP" screen displayed from the top screen. Refer to page 5 for how to 
call up the screen. 
10. Synchronization method selection [SYNC]
This unit supports the following 3 types of synchronization methods, and one of the following is selected. 
 (1)  Multiplexed vertical drive...

22
Step 1
Set "SYNC" to "LL" and press the setting button. 
  →  The "SYNC" screen appears. 
Step 2
Connect the video output signal and external synchronizing input signal of the camera to a 2-input oscilloscope, and move the cursor 
to "COARSE". 
Step 3
Adjust the oscilloscope to the vertical rate, and extend the vertical sy\
nchronizing part of the oscilloscope. 
Move the cursor horizontally with use of the right or left button to roughly adjust the vertical phase. 
The...

23
Step 3
Move the cursor to "POSITION" and press the setting button. 
Step 4
Use the up, down, right, and left buttons to determine the left upper po\
sition of the zone to be set and press the setting button. 
Step 5
Use the up, down, right, and left buttons to determine the lower right p\
osition of the zone to be set and press the setting button. 
  →  The asterisk mark "*" will be displayed after the number and the zone se\
tting will be saved. 
Note:
	 •	 To	delete	a	zone,	select...

24
14. Electronic zoom setting [EL-ZOOM]
Select "On" or "Off" to determine whether or not to use the electronic zoom. 
When "ON" is selected, the zoom factor and the panning/tilting settings \
can be configured. 
ON: Uses the electronic zoom. 
OFF (default): Does not use the electronic zoom. 
Follow the procedure below. Step 1
Move the cursor to "EL-ZOOM", select "ON" and press the setting button. 
  →  The "EL-ZOOM" screen will be displayed. 
Step 2
Move...

25
Back focus setting [BACK-FOCUS SETUP]
Selects  the  back  focus  setting  type  and  performs  fine  adjustment.  The  following  setting  can  be  configured  on  the  "BACK-FOCUS 
SETUP" screen displayed from the top screen. Refer to page 5 for how to call up the screen. 
The lens adjustment (+ Installation Guide) shall be performed before the back focus adjustment. 

The back focus adjustment is performed by changing the distance between \
the lens and focal point. 
Follow the procedure...

26
Step 3
Move the cursor to "C/L ← → B/W" and select the back focus adjustment type from the following: 
AUTO  (default):  Adjusts  the  back  focus  function  automatically  and  corrects  out  of  focus  when  switching  between  color  and  black- and-white images. 
PRESET:  Performs  the  preset  movement  to  each  specified  back  focus  position  when  switching  between  color  and  black-and-white  images.  The  preset  position  is  the  back  focus  position  specified  last  time,...

27
Special menu setting [SPECIAL SETUP]
The special menu setup is performed including the setting of the camera image quality and the communication configuration when a 
receiver is used. The following settings are to be configured on the "SPECIAL SETUP" screen displayed from the top screen. Refer to 
page 5 for how to call up the screen. 
Chroma level adjustment [CHROMA GAIN]
Use	the	right	 or	left	 button	 to	adjust	 the	color	 density	 of	the	 camera	 image.	When	the	level	 indicator	 moves	in...

28
Flaw compensation [PIX OFF]
Flaws in the displayed camera image are corrected. Up to 16 points can be corrected. 
Follow the procedure below. Step 1
Move the cursor to "PIX OFF" and press the setting button. 
  →  The "PIX OFF" screen appears. 
Step 2
Select a number (1 to 16) with which a pixel compensation point is registered and press the setting button. 
  →  The pixel compensation positioning screen appears. 
Step 3
Use the up, down, right, and left buttons to move the crosshair...

29
Language selection [LANGUAGE SETUP]
A  language  for  the  setup  menu  is  selected  from  the  following:  The  language  selection  can  be  made  on  the  "LANGUAGE  SETUP" 
screen displayed from the top screen. Refer to page 5 for how to call up the screen. 
JAPANESE/ENGLISH (default)/FRANÇAIS/ESPAÑOL/DEUTSCH/ITALIANO/êìëëäàâ
To change the language to be used, use the right or left button to select\
 the target language, move the cursor to "SET", and press the 
setting button....

30
Shortcut operation
Use  of  a  system  controller  with  the  "camera  function"  button  allows  users  to  perform  the  shortcut  settings  with  use  of  the  numeric 
keypad and camera function button. The available shortcut operations wit\
h this unit are shown as follows:
System controller operationSetting contents
[8]	+	[3]	+	[Camera	function] Super Dynamic ON (i-VMD)
[8]	+	[4]	+	[Camera	function] Super Dynamic ON
[8]	+	[5]	+	[Camera	function] Super Dynamic OFF
[9]	+	[0]	+	[Camera...