Panasonic Color CCTV Camera Wv Cw500 WV CW504 Series Operating Instructions

11
Step 2
Mask bright areas. 
Use  the  up,  down,  right,  and  left  buttons  to  select  an  area  to  be  masked  and  press  the  setting  button.  When  the  selected  area  is 
masked,  the  masked  area  will  start  blinking  (between  stripes  and  white  screen).  When  selecting  another  area  after  masking,  the 
masked area will be edisplayed in white. Repeat the above procedure to mask other areas as necessary. 
Note:
	 •	 To	cancel	the	masking,	select	the	masked	area	to	be	canceled,	and...

12
4. Gain control setting [AGC]
Select a gain control setting from the following. 
ON (HIGH) (default)/ON (MID)/ON (LOW): Automatically increases the gain to make the screen brighter when the illuminance of the subject becomes darker. 
    HIGH, MID and LOW indicate the gain level. 
OFF: Does not increase the gain. 
Note: 
	 •	 When	"SENS	UP"	is	set	to	the	AUTO	mode,	“AGC”	cannot	be	set	to	“OFF”.		
5. Electronic sensitivity enhancement setting [SENS UP]
Use  of  the  electronic  sensitivity...

13
When "AWC" is selected, follow the steps below to adjust the white balance. Step 1
Set "WHITE BAL" to "AWC" and press the left button to change to "AWC → PUSH SW". 
Step 2
Press the setting button and adjust the white balance. 
"PUSH  SW"  is  reversely  highlighted  during  adjustment.  When  the  reversely  highlighted  display  is  restored,  the  white  balance  adjust-
ment is completed. 
Step 3
Press the right button to select "AWC". 
Refer to the...

14
7. Digital noise reduction function setting [DNR]
The digital noise reduction function reduces noise automatically under the condition of low illuminance. 
The effect level of the noise reduction function is selectable from the following: 
LOW: Low level of noise reduction (small residual image)
HIGH (default): High level of noise reduction (large residual image)
8. Black-and-white mode setting [BW MODE]
The settings relating to the black-and-white mode can be configured. Follow the procedure below....

15
Step 4
Move the cursor to "DURATION TIME" and select a time for switching between color and black-and-white images from the following: 
(default: 10 seconds)
2 sec. - 10 sec. - 30 sec. - 60 sec.
  (S)  (L)
Step 5
Move the cursor to "BURST (BW)", and decide whether or not to provide a burst signal output in the black-and-white mode. 
ON (default): Provides a burst signal output. 
OFF: Does not provide any burst signal output. 
Note:
	 •	 Images	 may	not	be	displayed	 appropriately...

16
Perform the settings relating to the motion detection
Perform the settings relating to the motion detection as follows. It is possible to detect only objects that moves to the direction speci-
fied in advance or objects that keeps on moving for a certain duration. \
Up to 4 motions can be simultaneously detected. 
Follow the procedure below. Step 1
Move the cursor to "i-VMD" and press the setting button. 
  →  The "i-VMD SETUP" screen appears. 
Step 2
Move the cursor to "MOTION...

17
Step 6
Set the detection sensitivity and the minimum size of objects detected. Perform the setup while viewing the detection result displayed 
on the screen. 
Set the detection sensitivity
Move the cursor to "SENSITIVITY" and select one of the following options\
 for the detection sensitivity:
LOW (default)/MID/HIGH
Set the minimum size of objects detected
Move the cursor to "MIN SIZE" and select the minimum size of objects detected from the following: The size options will be...

18
Step 4
Move  the  cursor  to  "AREA"  and  select  the  area  for  which  the  detection  of  appearance/disappearance  of  stationary  objects  is  to  be 
set. 
ALL (default): All areas will be set as the detection area. 
SETUP:  When  the  setting  button  is  pressed  after  selecting  "SETUP",  up  to  2  areas  can  be  set  as  the  detection  area.  Refer  to  the   description below for how to configure the settings. 
Step 5
Move the cursor to "SENSITIVITY" and press...

19
Step 4
Use the up, down, right, and left buttons to determine the left upper po\
sition of the area to be set and press the setting button. 
Note:
	 •	 The	 area	corresponding	 to	the	 selected	 number	will	be	displayed	 in	a	green	 frame,	 while	the	other	 set	areas	 are	shown	 in	a	white	
frame. 
Step 5
Use the up, down, right, and left buttons to determine the right lower p\
osition of the area to be set and press the setting button. 
  →  The asterisk mark "*" will be displayed after the...

20
Configure frame display
Follow the procedure below. Step 1
Move the cursor to "i-VMD" and press the setting button. 
  →  The "i-VMD SETUP" screen appears. 
Step 2
Move the cursor to "INDICATOR" and determine whether or not to display a frame around the screen from the following. 
OFF (default): Does not display a frame. 
ON(ALL): Displays a frame. 
ON(OBJ): Display the appearance/disappearance frame only.  
Configure alarm notification
Follow the procedure below. 
Step 1
Move...